66cm (26”) LED TV with DVD & DVBT Model No.: DVL-2690 For information and support, www.lenco.
Contents 1-3 SAFETY INFORMATION 4 Product Introduction 4 Front View 5 6-7 8 Connecting external devices Remote Control Basic Operation 9-16 9 11 12 13 14 15 16 OSD Menu 17-19 20-22 23-24 Multimedia Operation Recording Operation Simple Troubleshooting 25-32 DVD Operation 33 34 Channel menu Picture menu Sound menu Time menu Option menu Lock menu Hotel menu TROUBLE SHOOTING GUIDE TECHNICAL SPECIFICATIONS
SAFETY INFORMATION IMPORTANT SAFETY INSTRUCTIONS - READ CAREFULLY BEFORE USE. Take note of the following safety information which appears on the back of the TV. CAUTION TO PREVENT ELECTRICAL SHOCK, DO NOT REMOVE ANY COVER SCREWS, NO USER SERVICEABLE PARTS INSIDE, REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. This symbol indicates that there are important operating maintenance instructions in the literature accompanying this unit.
IMPORTANT SAFETY INFORMATION (Continued) This unit has been produced according to all current safety regulations. The following safety tips should safeguard users against careless use and the dangers connected with such use. Although this appliance has been carefully manufactured and rigorously checked prior leaving the factory, as with all electrical appliances it is possible for problems to develop.
IMPORTANT SAFETY INFORMATION (continued) Liquids spilt into the unit can cause serious damage. Switch the set OFF and disconnect the mains power supply, then consult a qualified service person before attempting to use the unit again. Do NOT remove the safety covers. There are no useable or serviceable parts inside. You may invalidate the warranty. Qualified personnel must only service this apperatus. Do NOT tap or shake the screen, you may damage the internal circuits.
Product Introduction Front View INPUT LED Indicator Remote Control Window (keep clear) (IR) Infrared Receiver: Receives IR signals from the remote control. (Power on/Standby) LED indicator: Press POWER to turn on and off. Indicator on(Blue) Standby mode Indicator on(Off) Power on mode The effective receiving range for the signal is 5-8 metres from the front of the remote control window, and 300 to the left or right side and 200 above or below the control window. INPUT: Display the input source menu.
R-in RF Coax HDMI3 Connecting external devices (continued) USB HDMI1 HDMI2 SCART VGA PC-IN YPbPr Video L-in AC POWER IN AC POWER IN: 100-240V ~ 50/60Hz. USB: USB jack for Multi-Media playback and PVR.(Do not use USB extension cable to connect any USB device.) HDMI1/2/3: Connect it to the HDMI of DVD or other equipment. SCART: Connect them to the SCART video output terminal of DVD.(used in component source) PC-IN: Connect it to the audio output terminal of PC. VGA: For PC display.
Remote control The remote control is using Infra-Red(IR). Point it towards the front of the TV. The remote control may not work correctly if it is operated out of range or out of angle. POWER REC LIST MUTE EPG REP CH/LIST SUBTITLE PVR/DVD REC POWER: Turn the TV on/standby. MUTE: Press to mute the sound, press again or press VOL+ to unmute. REC LIST: Record List. CH/LIST: Display the programs list. SUBTITLE: Turn on/off the subtitle display in DTV mode and DVD mode.
Remote control (continued) POWER REC LIST MUTE EPG REP CH/LIST SUBTITLE PVR/DVD REC DISPLAY INPUT OK MENU EXIT 1 2 3 4 5 6 7 8 9 0 FAV PICTURE NICAM/A2 VOL SOUND CH / : Scan through channels. VOL / : Adjust the volume. PICTURE: Select the picture mode. NICAM/A2: TV Nicam/A2 select. SOUND: Select the sound mode. SLEEP: Standby timer. SCREEN: Turn on/off the screen. TV/TXT: Turn off/on the Teletext display. CANCEL: Cancel the Teletext display. REVEAL: Reveal any hidden text.
Basic Operation Basic Operation Power on/off 1. Connect to the power supply with the power code. 2. -To turn on the TV Press POWER button on the TV or remote control. -To turn off the TV Press POWER button on the TV or remote control.
OSD Menu OSD Menu 1. CHANNEL menu Description Auto Scan Press OK button to enter the hint menu, and select the Country and Tune Type mode for the TV, then press OK button to start auto tuning. DTV Manual Tuning Press OK button to enter the DTV Manual Tuning menu, select a DTV channel, and press OK button to start searching. ATV Manual Tuning Press OK button to enter the ATV Manual Tuning menu. Storage To: Select a position for storing the program. System: Select a TV system for searching.
OSD Menu OSD Menu Program Edit Press OK button to enter the Program Edit menu as the following picture. Rename Delete: Select a channel and press RED button, “Delete” will appear on the right of the program edit menu next to the channel you have chosen, then press RED button again, the program will be deleted. However if you decide not to continue to delete press the menu button to quit.
OSD Menu OSD Menu 2. PICTURE menu Description Picture Mode: Choose from Standard, Dynamic, User and Mild. Note: Contrast, Brightness, Color and sharpness are only available and can be adjusted in the User mode option in the Picture Mode Settings. Contrast: Controls the difference between the brightest and darkest regions of the picture. Brightness: Controls the overall brightness of the picture. Color: Control the color.
OSD Menu OSD Menu 3. SOUND menu SPDIF MODE PCM Description Sound Mode: Allows you to select among: Standard, Music, Movie, Sports and User. Treble(Could be adjusted when the sound mode is User): Controls the relative intensity of higher pitched sounds. Bass (Can be adjusted when the sound mode is set to User): Controls the relative intensity of lower pitched sounds. Balance: To adjust the balance of the left and right sound track, or turn off the volume of the left and right sound track.
OSD Menu OSD Menu 4. TIME menu Description Clock: Use the and buttons to select the position, and use the and buttons to set the time. Note: User can not change time manually during DTV mode, for time is from signal source directly. Off Time: Press OK button to enter the submenu, you could set the time when the TV set will be turned off automatically, you could also set the frequency.
OSD Menu OSD Menu 5. OPTION menu OSD Duration Description Language: Allows you to select menu language. Audio Language 1st/2nd (can be selected in DTV mode): Allows you to select first and second audio language. Subtitle Language 1st/2nd (can be selected in DTV mode): Allows you to select first and second subtitle language. OSD Duration: Allows you to setup the time of the menu display on the screen among: 5s, 10s, 15s, 20s, 25s, 30s, 35s, 40s.
OSD Menu OSD Menu 6. LOCK menu Hotel model Description Lock System: Turn on/off the Lock System function. Note: You should enter the code to operate the menu.(original code is 0000) Set Password: Set pin code. If the Pin code has been changed you must enter the present code. New : Enter the new password. Confirm: Enter the new password. Block Program: Lock the channel, you have to enter the code to view the channel.
OSD Menu OSD Menu 7.
Multimedia Operation Multimedia Operation Basic Operation 1). Press the INPUT button on the remote control to display the input source menu, select USB source by the / buttons, and press OK button to enter the Multimedia menu seen below. Input Source DTV ATV CADTV SCART YPBPR DVD PC HDMI1 HDMI2 HDMI3 AV USB Select 2). Insert USB device, you will find the name of the device display on the screen.
Multimedia Operation Multimedia Operation 1. Photo Play the photo Press / button to select the option on the table, and press OK button to change. Repeat: Select the repeat mode from Repeat All, Repeat 1, Repeat None. Music: Play/pause the music program (you can only play or pause the music you have programed). Playlist: Display the playlist on the screen, and you can select the photo by / button, and press OK button to program. Press / button to return to the options table.
Multimedia Operation Multimedia Operation 3. Movie Play the movie Goto Timer Press / button to select the option on the table, and press OK button to change. Repeat: Select the repeat mode from Repeat All, Repeat 1, Repeat None. Set A-B: Select and play the preferable paragraph of the program by seting A and B at the beginning and end, and there will be a sign on the left screen, press OK button again to cancel. Playlist: Display the playlist on the screen. Info: Display the information of the movie.
Recording Operation Recording Operation PVR settings Press the MENU button, and select CHANNEL menu. Record Timer 1). Recorded List Channel Recording list: Display the Recorder List menu. INFO: Display the information of the program you recorded. RED button: Delete the program you select. 2). Recorded Mode Set the recorded mode The TV will record the program automatically according to your settings. TITLE: Display the name of the recording program. MODE: Select the record mode.
Recording Operation Recording Operation 3). Schedule List Display the recorder shedule Note: a. Could’t add shedules which have existent on the list; b. Could’t add shedules when the list is full, you have to delete some schedules; c. You could delete a schedules by RED button on the remote control. 4). PVR File System Setup the PVR File system before you start recording. Select Disk: Select the device for the Record files. Check PVR File System USB Disc: Display the USB state.
Recording Operation Recording Operation 5) Record Start When you finish the settings above, you could start recording by select Start Recording in the menu and press OK button in DTV mode. (You can also start recording by press the REC button on the remote control) Record buttons REC(Recording): Press to enter the recording mode. PAUSE: Press to enter the timeshift mode. Recording list: Press to display the recording list. Stop: Press to stop recording.
Simple Troubleshooting Simple Troubleshooting If the display fails or performance dramatically deteriorates check the Display in accordance with the following instructions.Remember to check the peripherals topinpiont the source of the failure. If the display still fails to perform as expected,connect your helpline for assistance. No power - Check all connections to the TV. - Press either the power button or the Standby button on the Remote control.
24
DVD Operation DVD Operation Press the Power button on the TV or the remote control, then press the TV/AV button to select DVD mode. If there is no disc in the DVD player the screen will show "NO DISC". Insert Disc according to picture next to disc slot. Do not touch the playing surface. Hold the disc around the outside with your fingers and place the disc into the slot. The player will automatically draw the disc into the player.
DVD Operation DVD Operation 26
DVD Operation DVD Operation 27
DVD Operation DVD Operation Spdif Setup 28
DVD Operation DVD Operation or NO disc 29
DVD Operation DVD Operation 30
DVD Operation DVD Operation 31
DVD Operation DVD Operation 32
USER GUIDE TROUBLE SHOOTING GUIDE To assist in locating possible faults use the help guide below. SYMPTOM TROUBLESHOOTING No Picture, no sound Check that the TV is correctly plugged in. Check that the TV is connected to a suitable power source. Check the electrical supply is turned on. Ensure that the TV is powered on. Check that the cables are fitted securely. Ensure the aerial and/or external sources are connected. Press the INPUT button to change the source. Turn the TV on or off.
TECHNICAL SPECIFICATIONS Specifications of the TV that you have just purchased may vary from the information in this table due to technical innovations.
