User's Manual

IDENTIFICATION OF CONTROLS
1 STANDBY BUTTON
• Toggle this button to set the VISO 1 AP to standby mode or switch
ON the VISO 1 AP from standby mode.
• The VISO 1 AP can also be switched ON from standby mode by
pressing any of the panel keys S, M, + or - .
• When VISO 1 AP is switched ON from standby mode, the last Source
used will be selected.
NOTE
The Standby (ON/OFF) button will not shut down the VISO 1 AP.
Disconnect the mains power plug from the mains power source to
completely shut down the VISO 1 AP.
2 USB
• Allow direct connection and charging of Apple’s iPhone, iPad and
iPod touch using applicable connector (not supplied).
• VISO 1 AP may need a software update to be in step with the latest
technology trends. Connect to this input a USB memory stick
containing the software update.
• Only authorized NAD distributors or service centers are allowed to
implement a software update.
• Check with your authorized NAD distributors for future software
updates.
3 LAN
LAN connection must be setup for wired connection to be established.
Set up a Wired Ethernet broadband router with broadband internet
connection. Your router or home network should have a built-in DHCP
server to consummate the connection.
• Connect the VISO 1 AP to a network by directly connecting one
end of an Ethernet cable to the LAN port of your wired Ethernet
broadband router and the other end to VISO 1 AP’s LAN port. Use a
standard straight-through Ethernet cable (not supplied).
NOTE
AirPlay lets you stream music from your AirPlay-enabled device to the
VISO 1 AP. The AirPlay-enabled device and the VISO 1 AP must be in the
same network to send and receive streaming audio with AirPlay.
4 OPTICAL (S/PDIF) IN
• Connect OPTICAL IN of VISO 1 AP to the corresponding optical
digital output of sources such as CD, DVD or BD players, digital cable
box, digital tuners and other applicable components.
5 AC MAINS INPUT
• The VISO 1 AP comes supplied with a separate detachable mains
power cord. There are 2 supplied power cords – select applicable
type for your usage. Before connecting the plug to the mains
powers source, connect rmly rst the other end to VISO 1 AP’s AC
Mains input socket.
• Always disconnect the mains power plug from the mains power
source rst, before disconnecting the cable from the VISO 1 AP’s AC
Mains input socket.
• Power Rating: 100 - 240V ~50/60Hz 35W.
NOTES
• Disconnectthemainspowerplugfromthemainspowersourceto
completely shut down the VISO 1 AP.
• TheVISO1APwillpoweruptoitslastSourcesettingpriortobeingshut
down.
6 S, M,+/-
• Press “+” to increase the volume level; “ - ” to lower it.
• Toggle “M” to temporarily mute audio level or restore audio from
mute mode. “S” will continuously ash at mute mode.
• Pressing “+” or “ - ” will restore audio from mute mode.
• “S” indicator ashes whenever a remote control command is
received.
• Toggle “S” button to sequentially select through the following
source modes
a AirPlay/iOS/iPod nano device
b Bluetooth device
c Optical (S/PDIF) source
Below is a description of the various color modes of the S-indicator light.
S-INDICATOR LIGHT COLOR FUNCTION/DESCRIPTION
Alternately ashing in red and green
Ready to be congured
Factory default setting
Flashing green Access point/setup mode
Solid green AirPlay/iOS/iPod nano device source mode
Solid blue Bluetooth device source mode
Solid amber Optical (S/PDIF) source mode
O (no color) Standby mode
1
2
6
3
4
5
5
ENGLISHFRANÇAISESPAÑOLITALIANODEUTSCHNEDERLANDSSVENSKAРУССКИЙ