Datasheet

141www.lemo.com
®
®
2.5 24 2.9 2.5
3.0 24 3.4 3.0
3.5 24 3.9 3.5
4.0 24 4.4 4.0
4.5 24 5.2 4.5
4.0 36 4.5 4.0
4.5 36 5.0 4.5
5.0 36 5.5 5.0
6.0 36 6.5 6.0
7.0 36 7.7 7.0
7.8 36 8.8 7.8
4.5 42 5.2 4.5
6.0 42 6.9 6.0
7.0 42 7.9 7.0
8.0 42 8.9 8.0
9.0 42 10.0 9.0
2.5 30 2.9 2.5
3.0 30 3.4 3.0
3.5 30 3.9 3.5
4.0 30 4.4 4.0
4.5 30 4.9 4.5
5.4 30 6.0 5.4
6.5 30 7.0 6.5
1.2 22 1.4 1.1
1.8 22 2.1 1.8
2.5 22 2.8 2.5
2.8 22 3.1 2.8
3.2 22 3.5 3.2
2.5 22 2.8 2.5
2.8 22 3.1 2.8
3.2 22 3.5 3.2
The «GMD» are thin bend reliefs (for very flexible cables)
00
8.0 60 9.0 8.0
10.0 60 10.9 10.0
11.0 60 11.9 11.0
12.0 60 13.0 12.0
13.5 60 14.5 13.5
0B
0S FFM.0S.130.LC
0E-0K-0L FFM.0E.130.LC
2B
2S FFM.2S.130.LC
2E-2K-2L FFM.2E.130.LC
2C-2G FFM.2C.130.LC
3S FFM.3S.130.LC
3B FFM.3B.130.LC
3E-3K FFM.3E.130.LC
4S FFM.4S.130.LC
1B-1D
1S FFM.1S.130.LC
1E-1K-1L FFM.1E.130.LC
4S FFM.4S.130.LC
4B FFM.4B.130.LC
4E-4K FFM.4E.130.LC
1)
For use only with connectors from series 2B equipped with cable
fixing type M and where a bend relief from series 0B is used.
FFM.1B.130.LC
1)
For use only with connectors from series 3B equipped with cable
FFM.3B.131.LC
1)
fixing type M and where a bend relief from series 1B is used.
1)
For use only with connectors from series 4B equipped with cable
fixing type M and where a bend relief from series 2B is used.
FFM.00.130.LC
1) 1)
For unipole connectors
FFM.00.131.LC
2) 2)
For multipole connectors
Part number
GMA.00.012.DG
GMA.00.018.DG
GMB.00.025.DG
GMB.00.028.DG
GMB.00.032.DG
GMD.00.025.DG
GMD.00.028.DG
GMD.00.032.DG
Dimensions (mm)
Bend relief Cable ø
A L max. min.
Series Note
Part number
of nut for fitting
the bend relief
GMA.0B.025.DG
GMA.0B.030.DG
GMA.0B.035.DG
GMA.0B.040.DG
GMA.0B.045.DG
GMA.2B.040.DG
GMA.2B.045.DG
GMA.2B.050.DG
GMA.2B.060.DG
GMA.2B.070.DG
GMA.2B.080.DG
GMA.3B.050.DG
GMA.3B.060.DG
GMA.3B.070.DG
GMA.3B.080.DG
GMA.3B.090.DG
GMA.4B.080.DG
GMA.4B.010.DG
GMA.4B.011.DG
GMA.4B.012.DG
GMA.4B.013.DG
A bend relief made from thermoplastic polyurethane elas-
tomer (Desmopan 786) can be fitted over LEMO plugs and
sockets that are supplied with nut for fitting such bend relief.
They are available in nine different colours that match with
the GRA insulating washers (see page 144).
Use the part numbers shown below to order this acces-
sory separately.
Bend relief (Polyurethane)GM●
Note: the last letter «G» of the part number indicates the grey colour of the bend relief. For ordering a bend relief with another colour, see table on page
142 and replace the letter «G» by the letter of the required colour.
See also detailed information for each series: B series on page 54: K series on page 54; S series on page 107; E series on page 107.
GMA.1B.025.DG
GMA.1B.030.DG
GMA.1B.035.DG
GMA.1B.040.DG
GMA.1B.045.DG
GMA.1B.054.DG
GMA.1B.065.DG
L
ø A
Main characteristics
● Material: Polyurethane elastomer
● Temperature range in dry atmosphere: -40°C +80°C
FFM.0B.130.LC
FFM.2B.132.LC
1)
FFM.2B.130.LC
FFM.4K.132.LC
1)