LH670/675 1
CONTENTS Understanding your... Headset controls 4 Charging base 5 Indicator lights 6 Audio signals 7 How to...
UNDERSTANDING YOUR HEADSET CONTROLS A Speaker Volume Up & Mute B Speaker Volume Down & Mute A C D C FocusLight D Headset ON/OFF E Battery F Battery Door B E F WHAT’S IN THE BOX 4 Battery Door Headset 8.
UNDERSTANDING YOUR CHARGING BASE 1 Battery Indicator 2 Computer Mode Button 3 Bluetooth Mode Button 4 Telephone Mode Button 2 1 5 Bluetooth Connection Light 6 Charging Cradle 7 USB Connector Port 8 Power Port ９ EHS and Handset Lifter Port 10 Telephone Connector Port 11 Handset Connector Port 12 Microphone Volume Up/Down 13 Accessory Selection Switch 14 Compatibility Switch 7 8 3 4 5 ９ 10 11 6 13 12 14 5
UNDERSTANDING THE INDICATOR LIGHTS Device Lights Telephone mode Batter y Lights % Bluetooth ode 4 solid lights = 100% charge 3 solid / 1 flashing lights = 75% charge 2 solid / 2 flashing lights = 50% charge 1 solid / 3 flashing lights = 25% charge 4 flashing lights = less than 25% charge Computer mode Bluetooth connection light 6
UNDERSTANDING THE AUDIO SIGNALS SOUND WHAT IT MEANS 2 quick beeps (60 sec repeat) Low battery 2 beeps Nearly out of range 2 pitch tone Out of range 2 rapid beeps Back in range 1 beep Receiver volume up/down 2 pitch tone (8 sec repeat) Mute is on 1 beep Mute off/on When you walk out of range of the base, you will hear warning beeps in the headset. If the headset disconnects due to being out of range, the call will not drop. The headset will automatically reconnect when you are back in range.
HOW TO SET UP YOUR HEADSET 1 Plug the power adaptor into the charging base. The power light on the base will light up. We recommend charging your headset for at least 4 hours before use. 2a CONNECTING TO A TELEPHONE WITH A HEADSET JACK Use the included connector cord to connect the telephone port on the base to the headset port on your desk phone. You may need to adjust the compatibility switch on the bottom of the base to find the correct setting for your phone model. Most phones use 1.
3 CONNECTING TO A LEITNER HANDSET LIFTER (OPTIONAL) Connect your headset to your desk phone as shown in Step 2b. Attach the handset lifter to your desk phone and connect it to the AUX port on the charging base. Set the accessory selection switch on the bottom of the base to RHL. See the included user guide or go to headsets.com/LifterSetup for more help.
5 CONNECTING TO YOUR COMPUTER Use the included USB cable to connect the charging base to an available USB port on your computer. If your computer doesn’t recognize the device after a minute, go to your sound settings and select “Leitner Headset” as both your default microphone and default speakers. USB port 6 CONNECTING TO BLUETOOTH With your headset turned off, hold down the Bluetooth button ( １ ) for three seconds until the light starts flashing.
HOW TO MAKE A CALL 1 Make sure the base is in the mode that you want to make the call on Computer ( 1 ), Bluetooth ( 2 ), or Telephone ( ３ ) 1 2 ３ 2 Press the ON/OFF button ( 4 ). 3 Place your call on the device you are calling from. 4 Dial the number you’re calling. 5 To end the call: Place the headset on the charging base or press the ON/OFF button ( 4 ). If you have a handset lifter or an EHS cable, the call will disconnect automatically from your landline phone.
HOW TO ANSWER A CALL For incoming landline call: 1 Press the ON/OFF button ( 1 ) and make sure your base is in telephone mode ( 2 ). 2 Press the headset button on your 1 phone. If your phone doesn't have a headset button, simply lift the handset to activate the call.* If you have a handset lifter or EHS cable connected to the charging base, the line will be connected automatically. For incoming Bluetooth call: 1 Press the ON/OFF button ( 1 ) and your call will connect automatically.
HOW TO USE UNIBASE ® UniBase Technology allows you to conference calls between any two devices. Have a call on your cell phone and one on your landline? Conference them together with UniBase! 1 Begin a call on your first device. 2 Hold the mode button for the second device you want to add: Computer ( Bluetooth ( 2 ) or Telephone ( ３ ). 1 ), 3 After a few seconds, the mode button lights for the two selected devices will light up.
HOW TO CONTROL YOUR VOLUME To adjust the headset listening volume: While the headset is on, use the control buttons on the headset raise ( 1 ) or lower ( 2 ) the volume. The headset will beep each time the volume is adjusted. To mute the headset microphone: Press and hold either volume control button ( 1 or 2 ) for 2 seconds. While in mute mode, the FocusLight will turn purple on both the headset and base and the headset will beep every 60 seconds.
HOW TO ACTIVATE AUTO-ON Turn this feature on if you’d like your headset to turn on automatically when you pick up your headset off the charging base. To turn this feature on: With your headset turned off, hold the + and – buttons on your headset together for three seconds. Once auto-on is activated, the light on your headset will flash slowly. To turn this feature off: Follow the same steps again. This time the light on your headset will quickly flash.
HOW TO CONNECT A SECONDARY HEADSET FOR 1 Turn on the primary headset. 2 With the secondary headset turned off, place the secondary headset on the charging base.* 3 After a moment, the secondary headset’s FocusLight ( 2 ) will turn on and the charging base’s FocusLight ( 3 ) will flash to show that the headset is registering with the base. 4 Once the registering has completed, the base’s FocusLight ( 3 ) will stop flashing and the headset’s FocusLight ( 2 ) will begin flashing.
TRAINING OR CONFERENCE CALLS 5 If the secondary headset has Auto-On enabled, it will automatically connect when you lift it from the base. If it has Auto-On disabled, press the ON/OFF button ( 1 ) on the headset to connect. NOTE: The secondary headset will remain registered to the base until the primary headset is turned off or if either headset is returned to its original base. It takes about ten seconds for the secondary headset to re-register to its original base.
HOW TO REGISTER A NEW PRIMARY HEADSET In the event that you need to replace your headset, you’ll need to register it to your charging base 1 Set the headset into the charging cradle of the base. 2 The FocusLight on headset and the base will both flash purple when the headset goes into registration mode 3 Once the registration completes the FocusLight on the headset will turn off and the base light will turn solid blue 4 The headset will now be registered to the base.
TROUBLESHOOTING Q. I don’t have any battery lights on my headsets base and its been charging for more than 4 hours A. Check the battery orientation inside of your headset. The arrow on the battery should be pointing into your headset and the Leitner Logo facing the buttons of the headset. Q. My headset is charged and turned on but I can’t hear anything A. If you set up your headset through the headset jack, make sure your telephone’s headset button is on.
TROUBLESHOOTING Q. I can hear people on the phone but they can’t hear me. A. Try adjusting the microphone volume from the controls underneath the charging base. Call us at 1-800-432-3738 and we’ll make sure you sound perfect! Q. I can’t get my headset to work with my computer. A. Make sure the USB cord is connected between your charging base and computer.
HEALTH AND SAFETY It might seem a bit silly, but we’re required to tell you these safety instructions about your Leitner headset. Please keep these instructions for your reference. When using this product, these basic safety precautions and warnings should be followed to reduce the risk of fire, electrical shock, injury to persons, and damage to property. Operating, charging and storage temperatures are 32 °F to 104 °F (0 °C to 40 °C).
• Discontinue use of product if the product overheats, has a damaged cord or plug, if the product has been dropped or damaged, or if the product has come into contact with liquids. • This product should never be placed over or near a heat source and should not be placed in locations which do not have proper ventilation. • If you experience skin irritation after using this product, discontinue use. Charging Warnings • Use only the charger provided with your headset to charge the product.
Headset Battery Warnings • The headset is equipped with a replaceable battery. To reduce the risk of fire or injury to persons read and follow these instructions. • Do not dispose of the battery in a fire. The battery may explode. Check your local laws for disposal instructions. • Do not open or mutilate the battery. There may be corrosive materials which can cause damage to eyes or skin and may be toxic if swallowed.
For live product suppor t 1- 800 -432 - 3738 Mon - Fri 9am -7pm Eastern Time w w w.leitnerheadsets.
