Leica CS30 User Manual Version 0.
Introduction Congratulations on the purchase of the Leica CS30. Purchase This manual contains important safety directions as well as instructions for setting up the product and operating it. Refer to 1 Safety Directions for further information. Read carefully through the User Manual before you switch on the product. ☞ The content of this document is subject to change without prior notice. Ensure that the product is used in accordance with the latest version of this document.
Refer to the following resources for all CS30 documentation/software: the Leica USB documentation card • https://myworld.leica-geosystems.com • Leica Geosystems address book On the last page of this manual, you can find the address of Leica Geosystems headquarters. For a list of regional contacts, please visit http://leica-geosystems.com/contact-us/sales_support. myWorld@Leica Geosystems (https://myworld.leica-geosystems.com) offers a wide range of services, information and training material.
Table of Contents 1 Safety Directions 1.1 1.2 1.3 1.4 1.5 1.6 1.7 1.8 2 4 16 16 16 16 16 16 17 19 7 Overview Terminology System Concept 2.3.1 Power Concept 2.3.2 Data Storage Concept Container Contents CS Components User Interface 21 3.1 3.2 3.3 21 21 22 Operating Principles Home Screen LED Indicators on CS30 Operation 24 4.1 24 24 25 26 27 27 28 28 29 29 29 30 4.3 4.4 6 5 5 6 6 7 12 14 15 Description of the System 4.2 5 5 2.1 2.2 2.3 2.4 2.
1 Safety Directions 1.1 General Introduction Description The following directions enable the person responsible for the product, and the person who actually uses the equipment, to anticipate and avoid operational hazards. The person responsible for the product must ensure that all users understand these directions and adhere to them. About warning messages Warning messages are an essential part of the safety concept of the instrument. They appear wherever hazards or hazardous situations can occur.
Reasonably foreseeable misuse • • • • • • • • • • • Use of the product without instruction Use outside of the intended use and limits Disabling safety systems Removal of hazard notices Opening the product using tools, for example screwdriver, unless this is permitted for certain functions Modification or conversion of the product Use after misappropriation Use of products with recognisable damage or defects Use with accessories from other manufacturers without the prior explicit approval of Leica Geosyste
Person responsible for the product The person responsible for the product has the following duties: To understand the safety instructions on the product and the instructions • in the User Manual To ensure that it is used in accordance with the instructions • To be familiar with local regulations relating to safety and accident pre• vention To inform Leica Geosystems immediately if the product and the applica• tion become unsafe To ensure that the national laws, regulations and conditions for the oper• atio
WARNING Inadequate securing of the working site This can lead to dangerous situations, for example in traffic, on building sites and at industrial installations. Precautions: ▶ Always ensure that the working site is adequately secured. ▶ Adhere to the regulations governing safety, accident prevention and road traffic.
DANGER Risk of being struck by lightning If the product is used with accessories, for example on masts, staffs, poles, you may increase the risk of being struck by lightning. Danger from high voltages also exists near power lines. Lightning, voltage peaks, or the touching of power lines can cause damage, injury and death. Precautions: ▶ Do not use the product in a thunderstorm as you can increase the risk of being struck by lightning. ▶ Be sure to remain at a safe distance from electrical installations.
WARNING Short circuit of battery terminals If battery terminals are short circuited e.g. by coming in contact with jewellery, keys, metallised paper or other metals, the battery can overheat and cause injury or fire, for example by storing or transporting in pockets. Precautions: ▶ Make sure that the battery terminals do not come into contact with metallic objects. For the AC power supply: WARNING If unit is not connected to ground, death or serious injury can occur.
WARNING Improper disposal If the product is improperly disposed of, the following can happen: If polymer parts are burnt, poisonous gases are produced which may • impair health. If batteries are damaged or are heated strongly, they can explode and • cause poisoning, burning, corrosion or environmental contamination.
该环保使用期限是指在本指南所述的正常使用条件下,终端(不含电 池) 及其附件产品含有的有害物质或元素不会外泄,以及电子信息产 品用户 使用该产品时不会对环境造成严重污染或对其人身、财产造成 严重损害 的期限。 The environmental protection service life refers to the period during which the harmful substances or elements contained in the terminal (excluding battery) and its accessory products will not leak out under the normal use conditions described in this guide, and the users of electronic information products will not cause serious pollution to the environment or cause serious damage to their personal and p
CAUTION Intense electromagnetic radiation. For example, near radio transmitters, transponders, two-way radios or diesel generators Although the product meets the strict regulations and standards which are in force in this respect, Leica Geosystems cannot completely exclude the possibility that function of the product may be disturbed in such an electromagnetic environment. Precautions: ▶ Check the plausibility of results obtained under these conditions.
1.7 FCC Statement, Applicable in U.S. WARNING This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Exposure to radio frequency (RF) signals The wireless device is a radio transmitter and receiver. It is designed and manufactured not to exceed the emission limit for exposure to radio frequency (RF) energy set by the OET Bulletin 65 Supplement C / Ministry of Health (Canada), Safety Code 6. These limits are part of comprehensive guidelines and established permitted levels of RF energy for the general population.
2 Description of the System 2.1 Overview System components CS30 0021682_001 2.2 Terminology CS general description CS is a collective term describing the various models of the multi-purpose field controller which is used with GNSS and TS instruments. 2.3 System Concept 2.3.1 Power Concept General Use the batteries, chargers and accessories recommended by Leica Geosystems to ensure the correct functionality of the instrument.
☞ Removing the SD card or USB stick while the field controller is turned on can cause loss of data. Only remove the SD card or USB stick or unplug connecting cables when the field controller is switched off. Transfer data Data can be transferred in various ways. ☞ SD cards can directly be used in an OMNI drive as supplied by Leica Geosystems. Other PC card drives can require an adaptor. 2.
Container for GS instrument and accessories 2/2 f a b g c h d i e j 0014961_002 a b c d e f g h i j 18 GHT36 base for telescopic rod Antenna arm GFU RTK modem GAD32 telescopic rod GAT1 or GAT2 radio antennas GEB212, GEB260 (spare battery for CS30) or GEB331 batteries GRT146 or GRT247 carrier GAD33 arm GHT58 tripod bracket for GFU External battery Description of the System
Container for GS instrument and accessories a h i b j c d k e f l g 0014955_002 a b c d e f g h i j k l 2.
Underside of CS30 a b c d 0021685_001 e f g h i j k a b c d e f g h i j k Battery LED indicator Battery Camera LED flash nanoSIM card slot microSD card slot Card holder Docking contact pins Card slot Battery lock Speaker a b c d e Power key P1, function key 1 P2, function key 2 Kensington lock DC Jack Left side of CS30 a b c d e 0021686_001 Keys 20 Key Function Power key Power on. If the field controller is already on: Activate sleep mode when held for 2 s.