Instructions for Use Leica IP S Printer for slides Leica IP S, V 1.
Leica IP S Printer for slides Instructions for Use Leica IP S Order No. 14 0601 85101 RevD V 1.9 RevD, English - 05/2013 Always keep this manual with the instrument. Read carefully before working with the instrument.
NOTE The information, numerical data, notes and value judgments contained in this manual represent the current state of scientific knowledge and state-of-the-art technology as we understand it following thorough investigation in this field. We are under no obligation to update the present manual according to the latest technical developments, nor to provide our customers with additional copies, updates etc. of this manual. For erroneous statements, drawings, technical illustrations etc.
Table of contents 1. Important Information................................................................................................................ 6 1.1 1.1.1 1.2 1.3 1.4 Symbols in the text and their meanings..................................................................................... 6 Symbols on the transport packaging and their meanings...................................................... 7 Qualification of personnel....................................................................
Table of contents 6. 7. 8. Cleaning and Maintenance..................................................................................................... 51 6.1 6.2 6.3 6.4 Cleaning the instrument............................................................................................................. 51 Clean print head........................................................................................................................... 53 General maintenance.....................................
1. Important Information 1.1 Symbols in the text and their meanings Warnings appear in a gray box and are marked by a warning triangle . Notes i.e. important user information appear in a gray box and are marked by an information symbol . Inflammable solvent and reagents are marked with this symbol. Instrument surfaces which become hot during operation are marked with this symbol. Avoid direct contact with these surfaces - they may cause burns. Warning – Dangerous electrical voltage.
1. Important Information 1.1.1 Symbols on the transport packaging and their meanings The package contents are fragile and must be handled with care. Indicates the correct upright position of the package. The package must be kept in a dry environment. Example of labeling in accordance with IPPC • IPPC symbol • Country code in accordance with ISO 3166, e.g. DE for Germany • Regional identifier, e.g.
1. Important Information 1.2 Qualification of personnel 1.4 Instrument type • The Leica IP S may be operated by trained laboratory personnel only. • All laboratory personnel designated to operate this instrument must read these Instructions for Use carefully and must be familiar with all technical features of the instrument before attempting to operate it. All information provided in these Instructions for Use applies only to the instrument type indicated on the cover page.
2. Safety Make sure to comply with the safety instructions and warnings in this chapter. Make sure to read these instructions, even if you are already familiar with the operation and use of other products. 2.1 Safety instructions These Instructions for Use include important instructions and information related to the operating safety and maintenance of the instrument.
2. Safety 2.2 Warnings The safety devices installed in this instrument by the manufacturer only constitute the basis for accident prevention. Primarily responsible for accident-free operation is above all the institution which owns the instrument and, in addition, the designated personnel who operates, services or repairs the instrument. To ensure trouble-free operation of the instrument, make sure to comply with the following instructions and warnings.
2. Safety Warnings—Instrument operation • The instrument may be operated by trained laboratory personnel only. It must only be operated for the purpose of its designated use and according to the instructions contained in these Instructions for Use. • The instrument is de-energized after disconnection of the power supply through the power cable (power supply circuit breaker) - in emergencies, disconnect the power plug. • Do not touch the chute during operation. Risk of injury.
3. Instrument Components and Specifications 3.1 Overview—instrument 2 1 2.1 3 4 5 6 1 2 2.1 3 4 5 6 - 12 Basic instrument Slide Magazines Magazine no. 1 Control panel Lid Cover—cartridge slot Unload station (manual) Fig. 2 Instructions for Use V 1.
3. Instrument Components and Specifications Front view without lid Rear panel and electrical connections 12 2.1 -2.3 7 8 10 11 3 2 1 13 9 17 15 14 16 21 Fig. 3 2.1-2.3 - Magazine receptacles nos.
3. Instrument Components and Specifications 3.2 Technical data General Approvals: The instrument-specific approval marks are located at the rear panel of the instrument, next to the name plate. Nominal supply voltages: 100 to 120 V ~ +/- 10 % 200 to 240 V ~ +/- 10 % Nominal frequency: 50 to 60 Hz Power fuse: 2x T 3.15 A L250 V Maximum power draw at 100 - 120 V: 4.0 A Maximum power draw at 200 - 240 V: 2.8 A Leakage current at 240 V/50 Hz: ca. 2.
3.
3. Instrument Components and Specifications 3.3 Print specifications Only standard specimen slides with imprintable colored edges (23) can be imprinted in the Leica IP S (see Fig. 5). Printing directly onto the glass is not possible. Specimen slides with the following dimensions can be processed: 76 x 26 mm, max. 1.2 mm thick. Specimen slides with a white printed surface should be checked for print quality and ink resistance before purchase.
3. Instrument Components and Specifications Tested and recommended print media for the Leica IP S ink jet printer Important! The use of other print media may result in unsatisfactory print quality and/or jamming of slides/ cassettes during the printing process! If the specimen slides you are currently using are not listed above, please contact your local Leica Biosystems representative.
3. Instrument Components and Specifications 3.3.2 Print specifications Print resolution 24 Fig. 6 Printing area The printing area parameters listed in the table below are defined in the printer driver. Width Format Dots mm Slide 360 25.4 Print quality 18 The print head of the instrument has a preset resolution of 360 dpi in both directions (vertical and horizontal). Each printed line has a maximum height of 128 dots. This corresponds to a value of 9.03 mm.
3. Instrument Components and Specifications 3.3.3 Printing bar code Printer technology Creating bar codes Printing readable bar code depends on various factors that need to be taken into consideration in order to achieve results suitable for reliable and durable archiving.
3.
3. Instrument Components and Specifications 3.3.4 Resistance against reagents Caution! All laboratories must perform their own tests to ensure that the ink is resistant against the various reagents the slides will subsequently be exposed to. A wide range of factors beyond Leica's control can have negative effects on the results. The test conditions stated below can therefore only serve as an outline for individual laboratory test specifications.
4. Instrument Setup 4.1 Site requirements The instrument must not be operated in areas at risk of explosion. To ensure proper function of the instrument, it must be set up while maintaining a minimum distance of 10 cm from walls and furniture. - The instrument requires an installation area of approx. 650 x 550 mm. Relative humidity 80 % maximum - non-condensing Room temperature consistently between +15 °C and +35 °C Elevation: up to max. 2000 m NN The instrument is designed for indoor use only.
4. Instrument Setup • Unscrew the 8 screws (2, Fig. 8) on the sides of the wooden box and loosen the cover. • Remove the accessory box (7, Fig. 9) including accessories and packaging material) - directly under the lid. • Unscrew the 8 screws (3, Fig. 8) on the floor of the wooden box on the exterior. • Remove the interior carton around the instrument. • Carefully remove the wooden box from the baseplate. • The printer is secured with 4 plates (5) on the wooden floor of the outside box.
4. Instrument Setup 4.3 Installing the printer When unpacking the printer, at least two people (one person on each side of the printer) are required to lift the printer out of the box and place it onto the laboratory bench. 27 Fig. 12 Carefully pull out the transport anchor (27) of foam that protects the print head by pulling it to the right. Carefully remove any adhesive tape remnants. 24 • Check instrument for damage (do not switch on in the case of damage!).
4. Instrument Setup 4.
4. Instrument Setup 4.5 Installing the manual unload station 4 30 31 28 31 The enlarged detail shows the correct location of the collar screw once the unload station has been locked in place correctly. 26 32 27 The unload station supplied consists of: 26 - Unload station 27 - Screening plate 28 - Collar screws (3 pcs.) 29 - Slotted screws with washers (2 pcs.) Install as follows (Fig. 13): • Open lid (4). • There are 5 tapped holes (2 x item no. 30 and 3 x item no.
4. Instrument Setup 4.6 Automated unload station (optional) Optionally available for the printer is an automated multi-level cassette unload station, where the imprinted specimen slides are collected on individually removable and stackable trays (40) in the order in which they were printed. The multi-cassette unload station comes complete with 10 trays, all of which can be inserted simultaneously. Each tray holds up to 11 slides.
4. Instrument Setup 4.7 Installing/exchanging the flash bulb 41 49 42 Removing the old flash bulb Switch the instrument off and unplug it from power supply. Allow the flash tube to cool before removing it. Do not handle the flash tube with bare hands. Use a glove or tissue. • Open the lid (4, Fig. 2) to gain access to the reflector. • Remove screw (49) (use screwdriver supplied as part of tool set). Mind the washer (42). Fig. 15 Caution! To insert/remove, hold the flash bulb as shown in Fig.
4. Instrument Setup Inserting the new flash bulb 86 44 46 85 86 47 Fig. 19 48 47 Fig. 21 45 Fig. 20 • Insert the shielding glass (85) in the two holders (86). • Insert the new flash bulb into socket (46) (Fig. 21); then push it carefully inwards as far as it will go (Fig. 22) (the polarity marker (+) must not be visible any longer). If necessary, move flash bulb gently up and down.
4. Instrument Setup 4.8 Filling and inserting the magazines 48 51 50 49 52 Fig. 23 Fig. 24 Fig. 25 • Fill one of the magazines (48) with slides (49). While doing so, ensure that the surface to be imprinted (50) is on the left and facing upwards (Fig. 23). Fig. 26 • So that the specimen slides are ejected correctly, ensure that the specimen slides are inserted into the magazine accurately aligned above each other (Fig. 26) and at a right angle to the aperture (Fig. 27).
4. Instrument Setup Filling and inserting the magazines (continued) Filling capacities: Each magazine can hold up to 150 slides (depending on individual slide thickness). The maximum filling height of a magazine is indicated by the "max." mark (74) and may not be exceeded (Fig. 28). 48 74 Positively charged slides cling to each other so much that they require special handling to ensure reliable mechanical handling of this type of specimen slide by the printer.
4. Instrument Setup 4.9 Electrical connection The instrument must be connected to a grounded power socket. Of the set of power cords supplied, be sure to use only the one that is appropriate for the local power supply (plug must fit on-site wall outlet). Connecting to power supply • Make sure the printer is switched OFF, power supply switch (62) in position "0" = OFF. • Insert the correct power cord into the power input socket (63). • Switch on power switch (switch to position "I"= ON).
4. Instrument Setup 4.10 Exchanging the cartridge 4 5 85 64 Fig. 31 The printer is supplied with a cleaning cartridge (64) inserted. To be able to print, the cleaning cartridge must be exchanged for an ink cartridge. To do so, proceed as follows: • Open the cover plate (5) on the left side of the instrument (pressing its top left corner). • Unscrew the red cap (85) of the cleaning cartridge (64) by one turn (Fig. 31), then switch on the printer using the main switch on the rear side (item (62) in Fig.
4. Instrument Setup Exchanging the cartridge (continued) ð The last 30 seconds before the head closes are counted down. Fig. 34 85 Caution! If no key is pressed, the print head will close automatically 150 seconds after opening to prevent it from drying out. An acoustic signal (5 beeps) will sound after 120 seconds, after which the final 30 seconds will be counted down on the display. • Push the safety catch (86) forwards/to the right (open), so that the cleaning cartridge can be removed (Fig. 35).
4. Instrument Setup Exchanging the cartridge (continued) 66 Fig. 37 87 Fig. 38 65 Fig. 39 • Remove the ink cartridge (66) from the delivery carton and shake it a few times, then remove the protective foil. • The ink cartridge must be replaced after 60,000 printouts or 3.5 months. Record the installation date on the white surface (65) on the front (Fig. 39). • Insert the cartridge into the slot. Loosen the red screw-on cap one full turn but do not remove it yet.
4. Instrument Setup Exchanging the cartridge (continued) • The sensor in the cartridge slot recognizes the presence of a new cartridge. ð • The indicator LED "Ink Empty" goes out, code "88" appears in the display. At this point, the instrument has to be "told" which type of cartridge has been inserted. There are three options: 1. New ink cartridge: Press LOADED; the printer sets the ink level meter to 'full'. 2.
4. Instrument Setup 4.11 Installing the printer driver This printer driver only runs under the operating systems Microsoft Windows NT 4.0, Windows 2000 and Windows XP. Installation described is for Windows 2000. Any steps that need to be carried out in a different way when installing under other Windows versions are also explained below. "Microsoft", "Windows NT", "Windows 2000", “Windows XP” and “Windows 7 (32 bit and 64 bit)” are registered trademarks of Microsoft Corporation.
4. Instrument Setup 6. In the selection window, select PRINTERS IP-S (blue mark). If no (or other) selectable options are displayed, click on "HAVE DISK..." to return to the previous dialog box and repeat insertion of the path. 7. If the message shown on the left is displayed, the driver has already been installed on your PC on a previous occasion (e.g. interrupted installation or update). In this case, be sure to select REPLACE EXISTING DRIVER. 8.
4. Instrument Setup Configuring the serial port: 1. Open the printer folder: START --> SETTINGS --> PRINTERS 2. If you right-click on the icon of the newly installed printer, a quick menu opens up. Click on PROPERTIES.... 3. The PROPERTIES window contains several tabs; select the PORTS tab. Caution! Windows 2000 and XP do not contain the PORTS page. Fig. 41 4. The port selected during installation (COM 2 in the example here) must be highlighted. Enable the button ENABLE BIDIRECTIONAL SUPPORT. 5.
5. Operation 5.1 Control panel functions The control panel • consists of a membrane keyboard with six pressure-sensitive keys (four of them with an LED, two LED displays and a two-figure sevensegment display. • controls the printer functions and the print jobs that are defined via the control software. • indicates current printer status and processes in progress. • indicates errors and / or error messages. • controls the (optional) automated multilevel cassette unload station. MAG.
5. Operation POWER POWER Switching from POWER ON to STANDBY mode and back LED illuminated – POWER ON mode • Power is supplied to all printer systems. • The flash power supply is continuously being recharged. • The printer is ready to print immediately. LED flashes – STANDBY mode • All power absorbers of the printer are switched off, with the exception of those related directly to the processor (power saving mode). • The printer performs a print head clean at regular intervals (e.g. 4 times a day).
5. Operation ONLINE ERROR 42 Interrupting a print job in progress. LED on: Printer is ready and waiting for a new print job. LED flashing: A data transmission is in progress or a print job is being carried out. • Pressing ONLINE while a print job is in progress interrupts printing. The current print job, however, is completed. The online LED goes out. At that point the printer can be accessed e.g. to remove a half-empty magazine and refill it).
5. Operation CLEAN Cleaning the print head and carrying out a print test Pressing CLEAN briefly While a print job is in progress: • The print job is interrupted. "00" will appear in the display for about 2 s. • A print head clean is carried out and subsequently the print job is resumed. If no print job is in progress: • A print head clean is performed immediately after "00" has been displayed.
5. Operation TRAY LOAD If your printer is not equipped with an automated unload station, no function is assigned to this button! Controls the movement of the lifting table of the automated unload station (optional) Place a stack of trays (37) onto the lifting table of the unload station (Fig. 43). Any number of trays between 1 and 10 can be inserted, as the printer counts the trays when they are inserted. Once the lifting table has reached its highest position, the LED in the button starts blinking.
5. Operation 5.2 Display indications Display indication Magazine empty (in combination with "Mag. Empty" LED) 1 - Magazine no. 1 empty 2 - Magazine no. 2 empty 3 - Magazine no. 3 empty If "MANUAL FEED" has been selected in the printer driver settings, "0" will appear in the display after the print job has been sent. The printer will wait for an individual specimen slide to be placed in the feeding chute for printing. Display Status messages 00 Ink print head cleaning in progress.
5. Operation Status messages (continued) Display 14 Prompt requesting maintenance If this message is displayed, the instrument will be due for maintenance within the next few weeks. Confirm the prompt pressing ERROR. After about 3 weeks the message will be displayed again and will not disappear from the screen when pressing ERROR. You can still continue printing but maintenance must be carried out urgently.
5. Operation 5.3 Alarm functions The Leica IP S is equipped with two different alarm functions: Instrument alarm The printer has a beeper that emits acoustic signals indicating important instrument states and functions. • Upon pressing the button: 1 short beeping sound • Magazine empty/tray stack full: 2 short beeping sounds • In case of error: 5 short beeping sounds • When ending the head cleaning: 5 short beeping sounds Back panel of instrument ð Remote alarm 60 56 Fig.
5. Operation 5.4 Printer driver settings With the Leica IP S slide printer you can print slides from any Windows application allowing the user to individually configure the printing parameters. The description below refers to Microsoft Wordpad, a program that is part of any Windows installation and therefore available on all PCs supported by the printer driver.
5. Operation Selectable options in the PAPER --> SOURCE dialog box When clicking on the Source input field, an alphabetical list of all cassette supply options from all 6 magazines opens up. • MANUAL FEED means that individual slides will be placed onto the chute (12 in Fig. 3) and imprinted. The printer will not start printing until the sensor (13 in Fig. 3) reacts. • Further options are magazines 1 through 6.
5. Operation "ADVANCED OPTIONS" menu Clicking onto the individual menu items opens up a pull-down menu to their right, where you can select the desired parameters. Any menu items not described here are of no importance for the printer. Therefore, the standard settings of all menu items not described here should remain unchanged. • In the PAPER SIZE menu you select the size of the imprintable zone of the slide. Slide must be selected in this menu, otherwise printing will not be possible.
6. Cleaning and Maintenance 6.1 Cleaning the instrument Prior to cleaning the instrument, always switch off power supply and unplug the power cord! When handling cleaning detergents, follow the instructions of the manufacturer and make sure all laboratory regulations in force in your country are complied with. To clean the exterior surfaces, use a mild and ph-neutral commercial household cleaner.
6. Cleaning and Maintenance Slide guiding mechanisms • Drying station (Fig. 51) The chute must be clean. Caution! Sensitive electronics components are located in this area. Use no liquid in this area! Fig. 51 Drawer for broken glass 77 78 5 • The drawer for broken glass (77) is located above the slot for the ink cartridge, behind the left cover (5). It prevents glass dust and broken glass from falling into the interior of the instrument.
6. Cleaning and Maintenance 6.2 Clean print head Preparing the printer Once a week or if message "15" is displayed, the print head must be cleaned manually. 72 + • Open the printer lid and then press buttons CLEAN and LOADED simultaneously. • The print head (72) moves upward to a position approx. 1 cm away from the sealing lip (Fig. 53). Fig. 53 • Push the lever (69) upwards, then remove the red location plate (70) with the sealing lip (Fig. 54).
6. Cleaning and Maintenance Location plate 71 70 • Reinsert the location plate (70). Caution! The location plate must be completely dry. • When the cleaning process is finished, press any key of the control panel to confirm. • The print head moves back to parking position—message "15" disappears from the display. The printer is once again ready for printing. ð Fig. 56 • Also clean the location plate (70) and sealing lip with (clean) alcohol.
6. Cleaning and Maintenance 6.4 Storing the printer If the printer is not used for a long period of time (up to three months), the following instructions are to be followed. Important! • If the instrument remains connected to the power supply with the power on, the ink cartridge can remain in the printer up to its expiration date. • The print head drying out is prevented, because the printer regularly rinses the print head.
6. Cleaning and Maintenance Instructions for storage (continued) • Push a (new) cleaning cartridge as far as it will go into the shaft (Fig. 58). 64 • Unscrew the red cap (85) one turn and slide the cartridge fully home. • Push the security latch (86, Fig. 57) back in front of the cartridge. 85 Fig. 58 ð • The "Ink Empty" LED will go out and "88" will appear on the display. ð • Press CLEAN to rinse the print head; "00" will appear on the display.
6. Cleaning and Maintenance • Then pull out the location plate (70), (Fig. 60). Instructions for storage (continued) • Clean the print head with a foam swab, as described in Chap. 6.2, "Cleaning the print head" (see also Fig. 61). 70 Always use the cleaning swab for the print head once only. Never rotate the swab—this can damage the nozzle plate of the print head. Fig. 60 89 73 • After cleaning the print head, insert a new transport plate (73). • Push the small lever (69, Fig.
6. Cleaning and Maintenance Instructions for storage (continued) • Likewise, clean the removed removable disk (70) with the sealing lip with (clean) alcohol and a cleaning swab (89) (Fig. 62). 70 71 • The sealing lip (71) must be completely free of ink residue. Check the sealing lip for damage. Do not reuse a replacement plate with a damaged sealing lip. 89 Fig. 62 • Clean the instrument completely, as described in Chap. 6.1.
7. Troubleshooting 7.1 Malfunctions If the printer malfunctions during printing, a corresponding error code is displayed and simultaneously the LED in the ERROR button starts flashing. + How to eliminate the problem: • Determine the cause of the error—see error list (Chapter 7.3). • Remove obstruction(s); open lid if required.
7. Troubleshooting 7.2 Status messages (For additional information, refer also to Chap. 5.2) Display code "Mag. empty flashing" The printer is waiting for an individual cassette to be placed in the feeding chute for printing. "Mag. empty flashing" Magazine No. 1 empty "Mag. empty flashing" Magazine No. 2 empty "Mag. empty flashing" Magazine No. 3 empty – Ink print head cleaning is in progress. – Temperature in the flash power supply is too high.
7. Troubleshooting 7.3 Error messages Display code Source of error Troubleshooting solution Magazine output mechanically blocked. Remove the cause of the blockage. Faulty ejection of a slide. Magazine output blocked. Remove the slide. Transfer of a slide from the chute to the specimen Remove the slide. slide carrier failed. Horizontal motor either incorrectly positioned or mechanically blocked. Slide is stuck in the feeding chute. Remove the slide. Horizontal drive is mechanically blocked.
7. Troubleshooting Error messages (continued) Display code Source of error Cover (4 in Fig. 2) not closed properly. Safety switch triggered. Troubleshooting solution Ensure that the cover is not blocked, e.g. by the manual unload station. Close cover completely. Flash standby state not reached within the prescribed Call Leica Technical Service. time. Charging electronics defective. No flash or flash duration too short. Flash bulb dirty or defective.
7. Troubleshooting Error messages (continued) Display code Source of error Troubleshooting solution Faulty control data received (program bug) Carry out a RESET on the printer. Settings for the serial interface incorrect or the instru- Check cable connection to the PC. ment configuration conflicts with the PC configuration. Check configuration of serial port of the PC and reboot the PC.
7. Troubleshooting 7.4 Changing the flash bulb Code 13 is displayed when the flash bulb has reached its maximum serviceable life. When code 13 is issued, the bulb has to be changed. For details on how to insert / replace the flash bulb, please refer to Chapter 4.7. Before replacing the flash bulb, switch off the printer and unplug the instrument from power supply. 10 s After changing the bulb, switch the printer back on.
7. Troubleshooting 7.6 Replacing the fuses Before replacing a fuse, always switch the instrument off and unplug from power supply. Defective fuses may be replaced only with the replacement fuses supplied together with the instrument. Replacing the fuses 92 90 90 91 Fig. 65 Fig. 66 • Insert a screwdriver (91) into the slot in fuse holder (90); push slightly inwards and at the same time rotate the screwdriver 1/4 turn to the left. • The fuse holder is released and can be removed.
8. Warranty and Service Warranty Leica Biosystems Nussloch GmbH guarantees that the contractual product delivered has been subjected to a comprehensive quality control procedure based on the Leica in-house testing standards, and that the product is faultless and complies with all technical specifications and/or agreed characteristics warranted. The scope of the warranty is based on the content of the concluded agreement.
www.LeicaBiosystems.com Leica Biosystems Nussloch GmbH Heidelberger Straße 17-19 D- 69226 Nussloch Tel.: +49 - (0) 6224 - 143 0 Fax: +49 - (0) 6224 - 143 268 Web: www.LeicaBiosystems.
