Full Product Manual
AUGER
Somehow,
we
need
to
keep
this with
the
Shear
Pins
section.
This
is
probably
the
most important
section
for
people
to
read,
as
it
is
something they will
need
to
do
semi-frequently
))
When engaged, the augers rotate
and
pull snow
into
the auger housing.
DISCHARGE
CHUTE
))
Snow drawn into the auger housing
is
discharged
out
the discharge chute.
CHUTE
CLEAN-OUT
TOOL
Never
use
your
hands
to clear a
clogged
discharge
chute . Shut
off
engine
and remain behind handles
until all
moving
parts
have
stopped
before
unclogging.
The chute clean-out tool
is
conveniently fastened
to
the rear
of
the
auger housing
with
a mounting clip.
))
Should snow and ice become lodged in the discharge
chute during operation, proceed
as
follows
to
safely
clean the discharge chute
and
chute opening:
1.
Release
the auger clutch lever
and
shut
off
the engine.
2.
Remove
the
clean-out
tool
from
the
clip
which
secures
it
to
the rear
of
the auger housing.
3.
Grasp
the tool firmly by the
handle
and
push
and
twist the
tool into the
discharge
chute
to
dislodge the
blockage.
4. Refasten the clean-out
tool
to
the
mounting clip on
the rear
of
the auger housing.
5.
Make sure
the
discharge chute
is
pointed in a safe
direction
(no vehicles, buildings, people,
or
other
objects are in
the
direction
of
discharge). Restart
the engine. While standing in the operator's position
(behind the snow blower), engage the auger control
for
a
few
seconds
to
clear any remaining snow and ice
from the auger housing
and
the discharge chute.
HEADLIGHT
The
headlight
provides added safety in
))
low-visibility conditions. Turn the headlight
switch
to
the ON position
to
activate.
HEATED
HAND
GRIPS
))
To
activate
the
heated grips, move
the
switch into ON position.
It
is
recommended
that
you
wear
gloves
when
using
the
heated
grip.
FUEL
SHUTOFF
VALVE
Always operate the snow blower with the fuel shut-off
))
valve
in
the
OPEN
position.
Close
the valve when
you
do
not
use
the
machine.
CHOKE
CONTROL
The choke
control
is used
to
choke
the
carburetor
\.\. and assist in
starting
the
engine. The choke control
//
switches
between
the
CHOKE
CLOSED
l'-1
and
CHOKE OPEN
I f I positions.
&
Never
use
choke
to
stop
engine.
PRIMER
Press
the
primer
to
pump additional fuel
from
the
))
carburetor
to
the cylinder
for
improved cold weather
starting. Do not push primer more than 3 times when
starting engine cold.
RECOIL
STARTER
HANDLE
))
The handle
is
used
to
start the engine.
SAFETY
IGNITION
SWITCH
\.\. Insert the safety ignition key
for
engine
to
start
and
//
run.
To
stop the engine, remove the
key.
RUN/STOP
SWITCH
Used
to
stop
the
engine.
Move
switch
to
STOP
))
position
to
stop engine.
Place
switch in
RUN
position
for
engine
to
start
and
run.
ELECTRIC
STARTER
&START
BUTION
The electric
starter
will
start
a properly choked and
))
primed engine when start button (120V
AC)
is
pushed.
To
start
the
machine, connect the electric
starter
to
))
an
electric power source
with
an
approved extension
cord
and
press the start button.
Thoroughly inspect the electrical cord before
using the machine.
If
the cord
is
damaged,
do
not operate the
machine.
Replace
or repair the
damaged
cord
immediately.
Connect extension cord to the electric starter
plug-in
(rrst
and
then
to a
power
outlet;
disconnect
the
extension
cord
from
the
power
outlet (rrst
and
then
from
the
machine.
To
prevent damaging the electric starter,
do
not
run
it
more
than
5
continuous
seconds
each
time
you
try to start. Wait 10
seconds
between
each
attempt.
Know
Your
Machine I
14