Owner's Manual OUTDOOR FIRE PIT TABLE MODEL MO.:WELLFP-S-CA2(5)/CDFP-S-CA/CDFP-S-CA HB /CDFP-S-Camocha/CSFP-S-CAwood /vc-CDFP-S-Camocha/vc-CDFP-S-Cawood /v-CDFP-S-CA/CDFP-S-CA5 ANS Z21.97-2010, Outdoor Decorative Gas Appliances CGA CR 97-003 Outdoor Gas Fireplaces INSISTS ON THE HIGHEST STANDARD OF QUALITY IN MANUFACTURING. IN CASE OF ANY ISSUES DO NOT RETURN TO STORE. CALL 1-800-379-2185 OR E-MAIL US AT info@calell.com WITH QUESTIONS OR WARRANTY ISSUES.
SAFETY INFORMATION Before you assemble or operate this unit, please carefully read this entire manual. Failure to do so WARNING • The installation of this unit must adhere to local codes or either the National Fuel Gas Code, ANSI Z223. 1/NFPA54, OR CAN/CGA-B149.1, National Gas and Propane Installation Code. • THIS UNIT IS INTENDED FOR OUTDOOR USE ONLY! This product shall be used outdoors, in a ventilated space and shall not be used in any enclosed area.
SAFETY INFORMATION • Combustible material should not be within 72 inches of the top of the unit, or within 48 inches around the entire unit. • vapors and liquids. • • Do not add water into the unit. • Do not operate unit if any part has been under water. Call a service technician to replace any damaged parts should this occur. • Do not disconnect any part while unit is in use. • Do not store a spare propane tank on or near this unit.
SAFETY INFORMATION NOTE: You must follow all steps to properly assemble this heating item. Make sure the gas valve is turned “OFF” before assembling. Do NOT attempt to assemble without proper tools. Min. Clearance 48 in. (121.9 cm) Min. Clearance 48 in. (121.9 cm) Min. Clearance 48 in. (121.9 cm) Combustible materials should not be within 72 inches of the top of the unit, or within 48 inches around the entire unit. Min. Clearance 48 in. (121.
HARDWARE AA BB CC DD EE FF GG HH II Item Description Qty AA M6 x 20 Bolt 8 BB M6 Washer 8 CC M6 x 30 Bolt 4 DD M8 x 16 Screw 4 EE M8 Washer 4 FF Propane Tank Strap 2 GG Touch Up Paint 1 HH Allen Wrench 1 II Wrench 1 Before beginning assembly of this product be sure all parts are present. Compare parts with package contents list and hardware contents list.
CONTENTS K A I L B J E C D F G M H O N Item Description Qty A Lid 1 B Firebowl 1 C Back Panel 1 D Table Top 1 E Left Side Panel 1 F Right Side Panel 1 G Bottom Plate 1 H Door Panel 1 I Burner (preassembled) 1 J Guard (preassembled) 1 K Control Knob (preassembled) 1 L Igniter (preassembled) 1 M Battery (AA) 1 N LavaGlass™ 2 bags O Protective Cover 1 6
ASSEMBLY INSTRUCTIONS 1. Align the back panel (C) to the left side panel (E). Then attach by placing a M6 x 20 bolt (AA) through a M6 washer (BB), put the bolt and washer through the aligned bolt slots and loosely tighten with allen wrench (HH). (You will use two bolts and two washers for this step.) Be sure not to over tighten - you may need to adjust the panels later on to ensure proper alignment. E 2. Align the door panel (H) to the right side panel (F).
ASSEMBLY INSTRUCTIONS 4. Attach two propane tank straps (FF) to the bottom plate (G) in two cross corners as shown. FF G FF 5. Rotate the door knob to unlock; open the door on the door panel (H). Place the bottom plate (G) into the front of the panel assembly as shown. Secure the bottom plate (G) to the panels by using four M6 x 30 bolts (CC). Tighten with wrench (II). G 6. Remove the preassembled screws and washers from the corners of the burner assembly (B).
ASSEMBLY INSTRUCTIONS 7. Attach the table top (D) to the panel construction by aligning the holes at the bottom of the table top (D) to the holes in the top of the panel construction and securing with four M8 x 16 bolts (DD) and four M8 washers (EE); tighten with wrench (II). Be sure to position the control panel to be over the door panel (H). D adjusting and tightening to ensure the structure is sturdy. 8.
ASSEMBLY INSTRUCTIONS 10. Place a 20 lb. propane gas tank (not included) into the round stand on bottom plate (G). Insert one propane tank strap (F) through the handle holes on the collar of the 20 lb. propane gas tank. Connect with the other propane tank strap (F) by attaching the buckles together. Tighten to secure. G F 11. Turn the cylinder valve on the tank clockwise to close the propane tank.
OPERATION Before performing a leak test, be sure that no sparks can occur and you are in a spacious outdoor area. Connect the propane gas tank to the regulator and turn the valve on the unit to the “off” position. Brush a soap and water mixture on all connections. Turn the gas supply on; if bubbles occur on any connection there may be a leak. If you smell gas or a leak is discovered turn the gas valve off, disconnect propane gas tank and do not use the appliance until the leak is repaired.
TROUBLESHOOTING Problem Heating unit won’t light Burner won’t light while using a match Cause Solution Igniter pin and burner are wet Dry off with a soft cloth Igniter battery is incorrectly inserted Check which direction the battery is inserted Igniter pin is broken Contact Bond Manufacturing for a replacement part Electrode wire is loose or disconnected Reconnect wire to the igniter box located inside the table behind the igniter box Electrode wire is shorting between valve and igniter pin C
