Instructions

ManualsBrandsLEE ManualsApp PressLEE PA5413 Deluxe App Press

PA5413

DELUXE APP PRESS

Base Casting

Part # AC4899

Upper Casting

Part # AC4898

Roller Handle # 91629

Case Feed Spring

Part # PR2118

optional Reloading Stand

Product # 90688

Case Feed Magazine

# 90242

Guide & ejector # AC1177

Priming should not be attempted by persons not willing and able to read and fol low instructions exactly. Do not permit distractions

while priming.

Children should not be permitted to prime without strict parental supervision.

Always wear safety glasses and hearing protection when priming and shooting.

Primers, like gasoline and matches, can be dangerous if improperly handled or misused.

CAUTION

WARNING: Handling live primers and spent primers may expose you to lead or other chemicals, which are known to the State of

California to cause reproductive harm and cancer. For more information, go towww.P65Warnings.ca.gov.

WEAR SAFETY GLASSES AND HEARING

PROTECTION WHILE PRIMING

SMOOTH OPERATING TIP

• Lubricate columns and

all pivot points using any

heavy oil.

www.leeprecision.com

WARNING

Primers will explode if they are impacted, shocked or crushed. Wear hearing and eye protection at all times.

Case Inserter

Part # PA4342

Case Risers

Part # PA4384

Folding tray (1 included) # 90606

Bottle

Adapter

# 91151

Deluxe Rail

Part # PA5222

Small, Large, Deprime inserts

# AC5080

Not pictured:

Adapter spring # PT3295

Small pin = # AC2241

Large pin = # AC905

Breech Lock Prime Die

Part # AC2279

Guide

Ejector

Trough # 92041

Primer Feed Spring # PR2118

Primer

Body

# AC5387

Primer escape lever

Rail Detail (see top of page 7 for section view)

Gate

Spring snugger

Primer slider

Primer size button

selector

Trough bottom

Deluxe

App

Rail

We’ve include a shell holder

adapter with your tool. Use

this insert if you intend to

swage primer pockets, bulge

bust or use our bullet sizing

kit. See page 7.

Not pictured:

Part # PA4318 Spring

Part # AC1175 Push Rod

*FREE* AC3993 Decapper

Summary of content (7 pages)

PAGE 1
DELUXE APP PRESS Rail Detail (see top of page 7 for section view) www.leeprecision.com Case Feed Magazine # 90242 Deluxe App Rail Roller Handle # 91629 Primer escape lever Spring snugger Gate Primer slider Primer size button selector Breech Lock Prime Die Trough bottom Part # AC2279 Not pictured: Part # PA4318 Spring Part # AC1175 Push Rod *FREE* AC3993 Decapper Ejector Guide We’ve include a shell holder adapter with your tool.
PAGE 2
MOUNTING DELUXE APP KIT Press fits directly on LEE Steel Base Block included with Reloading Stand # 90688 or Bench Plate # 90251. - OR Mount using three, ¼” (6mm) bolts and nuts. Drill three 17/64” (7mm) holes in your work bench. CONFIGURING DELUXE APP KIT 1 Adapter spring # PT3295 Small pin Large pin # AC2241 # AC4905 2 Slide the primer spring over the correct primer pin and install into the correct priming insert.
PAGE 3
8 A ADJUST JAWS & RISER INSTALLATION B Use a small flat blade screwdriver for the jaw adjustment. With the handle in the down position, screw clockwise to tighten or counterclockwise to loosen. The tips of the jaws should be set slightly smaller than the case you are feeding. Five risers are included, PA4384A-PA4384E. Only A, B, C and E will be used for case feeding. Select the tallest riser that is NOT taller than the case when installed on the case inserter.
PAGE 4
8 BEGIN PRIMING A Insert deprimed case into case inserter. IMPORTANT Verify position of button on rail. Section view left shows small primer position. Button up / above rail = small primers WARNING Wear hearing and eye protection while operating. Glide finger along bottom of rail to verify bottom of primer size selector button is flush. B Raise lever to center case on priming insert, ready to be primed. C Cycle the press lever down to the stop to prime. No feel is required to properly seat primers.
PAGE 5
INSTALL CASE FEED MAGAZINE Works well with most handgun and small rifle cases like the 223. Can be fitted with optional collator bowl # 90667, fills 4 tube feeder with handgun cases in about 10 seconds. TOOLS REQUIRED & SETUP • 7/16” wrench case feeder assembly has a SMALL and a LARGE hole. See the cartridge 1 The setup chart (below, right), find the cartridge you wish to set the case feeder up for. See [FIGURE 1 through 2] to set up feed plate your cartridge calls for. case into jaws of slider base.
PAGE 6
4 Test operation on a few cases. If the cases drop too soon, they may rest on top of feed fingers. Rotate the feed tube support farther away (clockwise) from the press to delay the dropping. Because of the wide range of diameters and rim configurations, you will have to fine tune this position to provide reliable feeding. OPTIONAL CASE COLLATOR product # 90667 Works on most handgun cases, fills in about 10 seconds.
PAGE 7
TROUBLESHOOTING PROBLEM Primer doesn’t feed Primer doesn’t enter case CAUSE REMEDY • Full lever stroke not be made • Primer trough not full • Primer size button selector on rail is in incorrect position. • See page 4, step D. You must push lever from stop to stop to feed the next primer. • Maintain minimum of 6 primers in trough • See section views below, button must in correct position small or large to feed primers.