LTK-1600TN User Manual LEE TECHNOLOGY KOREA CO., LTD. email sales@leetek.org website www.leetekorea.com KOREA HEADQUARTER 3rd Fl. 499-2, Sang3-dong, Wonmi-gu, Bucheon City, US OFFICE 530 Highland Station Drive, Suite 2004, Sewanee, GA 30024, U.S.A.
NOTICE This manual, software and electronic circuitry are copyrighted. All rights reserved. Under the copyright laws, this manual, software and electronic circuitry may not be copied, in whole or in part without written prior consent of Lee Technology. All information provided in this document is carefully prepared and offered in good faith as a guide in the installation, use and servicing of our products.
IMPORTANT SAFETY INFORMATION CAUTION: To comply with FCC RF exposure compliance requirements, a separation distance of at least 20 cm must be maintained between the antenna of this device and all persons. This device must not be colocated or operation in conjunction with any other antenna or transmitter. Any changes or modifications (including the antenna) made to this device that are not expressly approved by the manufacturer may void the user’s authority to operate the equipment.
Tablecall Paging System User Manual TABLE OF CONTENTS 1. SYSTEM INTRODUCTION 1) SYSTEM SUMMARY 2) SPECIFICATION 2. INSTALLATION 1) EQUIPMENT SETUP 2) PLACEMENT 3. NUMBER SETTING (CAPCODE PROGRAMMING) 1) NECESSARY THINGS TO PREPARE CAPCODE PROGRAMMING 2) AVAILABLE OPERATION SYSTEM 3) SEQUENCE TO SET PROGRAMMER SOFTWARE 4. RECEIVER SETTING 1) POWER ON / OFF 2) TABLE SETTING 5. OPERATION 6.
Tablecall Paging System User Manual 1. SYSTEM INTRODUCTION 1) SYSTEM SUMMARY LEETEK’s Tablecall Paging System was designed specifically to help guests immediately page their servers or managers when they need anything, so they can be served whenever they want. With this solution, it is needless guest’s are waiting for their turns for served and servers are more convenient because it is needless to visit guest’s table twice and it will keep servers from duplicating with each other.
Tablecall Paging System User Manual 2. INSTALLATION 1) EQUIPMENT SETUP (1) Transmitter Unwrap all sending unit components. Plug the power supply with the large tip into a standard outlet and plug it into charger base for transmitter. Stack the transmitters on the charger base. The red indicator will be lighted on and it means the transmitters are charged properly. We recommend some type of surge suppressor on the power supply for protection. Power surges are not covered under system warranty.
Tablecall Paging System User Manual 3. RECEIVER SETTING * RECEIVER (Belt Type Pager) Side Button 1) SPEC 12 Segments Display Battery Rechargeable Button Switch (Side Button) Vibe and Beep Alert 2) POWER ON/OFF ON – Press the side button for 5 seconds. OFF – Press the side button for 5 seconds, it will display “Set Table”. Once again, press the side button shortly, it will show “Power Off”.
Tablecall Paging System User Manual ※ Be aware that you have to press the “Waiter” button as soon as you enter the Table Setting Mede at Belt Pager. Otherwise, you will be automatically exited from the Table Setting Mode. (2) Table Cancellation (Belt Pager) Press the Side Button for 5 seconds on the Belt pager. “SET TABLE” will show on the display. Press the side button for 5 seconds, and it will be into the Table Setting Mode (Wireless Programming Mode).
Tablecall Paging System User Manual * RECEIVER (Watch Type Pager) ① Top Button ② Side Button 1) SPEC 12 Segments Display AAA Battery included Two Buttons are available (Top & Side) Vibe and Beep Alert 2) POWER ON/OFF ON – Press the side button for 5 seconds. OFF – Press the side button for 5 seconds 3) TABLE SETTING ※ One pager can be assigned Max. 60 number of transmitters.
Tablecall Paging System User Manual (2) Table Cancellation (Watch Pager) Press the Top Button for 5 seconds on the Belt pager, and it will be into the Table Setting Mode (Wireless Programming Mode). As soon as you enter the Table Setting Mode, press the “Manager” button on the transmitter for 5 seconds (Until you can feel the vibration from the belt pager), and then the table assignment will be canceled from the transmitter.
Tablecall Paging System User Manual 5. HOW TO USE 1) Restaurant, Hotel, Café (1) Direction for Use - For calling staffs (2) Process - A guest can page to waiters by pressing the “WAITER” button on the transmitter, when the guest needs some help to request such as receipts or menu order. - If the guest is not satisfied by the services from waiters, he/she can page to Manager by pressing the “MANAGER” button on the transmitter.
Tablecall Paging System User Manual the guest needs some help. - After serving the services, the waiter can press the “CANCEL” button to complete the guest’s requests. (3) Merits - This paging system can be used in a crowd place where guests are not able to call waiters by voices. - It will also help reduce the number of servers.
