Installation Guide
DSA DMX512-SPI Decoder and RF Controller
User Manual Ver 1.0.9
Page 2
V+
V-
DA
V+
V-
DA
● RGB order: O-1 - O-6 indicate six order (RGB, RBG, GRB, GBR, BRG, BGR).
● Pixel length: Range is 008-900.
● Automatic blank screen: enable ("bon") or disable("boF") automatic blank screen.
● Short press M key, when display 001-999, enter DMX decode mode.
● Press ◀ or ▶ key to change DMX decode start address(001-999),
long press for fast adjustment.
● Long press M key for 2s, prepare for setup decode number and multiple of pixels.
Short press M key to switch two item.
Press ◀ or ▶ key to setup value of each item.
Decode number(display "dno") : DMX decode channel number, range is 003-600(for RGB).
Multiple of pixels(display "Pno") : Each 3 DMX channel control length(for RGB), range is 001- pixel length.
Long press M key for 2s, or timeout 10s, quit setting.
● If there is a DMX signal input, will enter DMX decode mode automatically.
No.
IC type
TM1829
TLS3001,TLS3002
GW6205
MBI6120
TM1814B(RGBW)
SK6812(RGBW)
UCS8904B(RGBW)
LPD6803,LPD1101,D705,UCS6909,UCS6912
LPD8803,LPD8806
WS2801,WS2803
P9813
SK9822
TM1809,TM1804,TM1812,UCS1903,UCS1909,UCS1912,
UCS2903,UCS2909,UCS2912,WS2811,WS2812
TM1803
C11
C12
C13
C14
C15
C18
C21
C22
C23
C24
Output signal
DATA
DATA,CLK
DATA,CLK
DATA,CLK
DATA,CLK
DATA,CLK
DATA
DATA
DATA
DATA
DATA
DATA
DATA
DATA
Dynamic mode list
● Short press M key, when display P01-P32, enter stand-alone mode.
● Press ◀ or ▶ key to change dynamic mode number(P01-P32).
● Each mode can adjust speed and brightness.
Long press M key for 2s, prepare for setup mode speed and brightness.
Short press M key to switch two item.
Press ◀ or ▶ key to setup value of each item.
Mode speed: 1-10 level speed(S-1, S-9, S-F).
Mode brightness: 1-10 level brightness(b-1, b-9, b-F).
Long press M key for 2s, or timeout 10s, quit setting.
● Enter stand-alone mode only when DMX signal is disconnected or lost.
● Long press ◀ and ▶ key, restore factory default parameter, display"RES".
● Factory default parameter: DMX decode mode, DMX decode start address is 1, decode number is 510,
multiple of pixels 1, dynamic mode number is 1, chip type is TM1809, RGB order,
pixel length is 170, disable automatic blank screen, without matched RF remote.
Match: Long press M and ▶ key for 2s, display "RLS",
within 5s, press on/off key of the RGB remote, display "RLO", match is , successful
then use the RF remote to change mode number, adjust speed or brightness.
Delete: Long press M and ▶ key for 5s, until display "RLE", delete all matched RF remote.
DMX decode mode
Stand-alone mode
Speed
(8 level)
Brightness
(10 level,100％)
P01
P02
P03
P04
P05
P06
P07
P08
P09
P10
P11
P12
P13
P14
P15
P16
P17
P18
P19
P20
P21
P22
P23
P24
P25
P26
P27
P28
P29
P30
P31
P32
Red horse race white ground
7 color jump sectionally
7 color strobe sectionally
6 color smooth sectionally
7 color chase
Red Yellow float
Green Cyan float
Blue Purple float
RGBW float
No.
Name
No.
Name
No.
Name
Blue White float
Purple float
Red float
Green float
Blue float
Blue meteor
White meteor
7 color meteor
Purple meteor
RGB chase
Blue White chase
Green Cyan chase
Green horse race white ground
Blue horse race white ground
Yellow horse race blue ground
Cyan horse race blue ground
Purple horse race blue ground
7 color multi horse race
7 color scan close + open
7 color multi-scan close + open
7 color horse race close + open
7 color multi horse race close + open
6 color float
● IC type table:
DMX decode mode
Stand-alone mode
RF mode
Restore factory default parameter
IC type RGB order
Operation
● You must first assure IC type, RGB order and pixel length of the LED strip is correct.
● Long press M and ◀ key, prepare for setup IC type, RGB order, pixel length, automatic blank screen,
Short press M key to switch four item.
Press ◀ or ▶ key to setup value of each item.
Long press M key for 2s, or timeout 10s, quit setting.
IC type, RGB order and pixel length length setting
pixel length disable automatic blank screen
C16
C17
C25
DMX CH
DMX Data
255
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18
0 0 0 255 0 0 0 255 0 0 0255 255 255 255 255 255
DMX data from DMX512 console:
For example, the DMX-SPI decoder connect with RGB strip:
DMX-SPI decoder output (start address: 001, decode channel number: 18, each 3 channel control length: 1):
DMX-SPI decoder output (start address: 001, decode channel number: 18, each 3 channel control length: 3):
C19
C31
DATA
TM1914A
C32
DATA
GS8206,GS8208