I. Product Summarize 1. Product constitute 1. LED-WiFi Controller 2. Wireless remote controller 3. CD It is the core of product, responsible for receive control signal and control LED equipment. In the condition of not use the mobile phone as remote control, you can choose RF remote control to control LED. Include IOS operating system and Android operating system mobile soft. 2.
II. Technical Parameters 1. Remote control technical parameters 1：Working temperature：-20-60° C 2：Power supply method：AAA*3 3：Supply voltage：1.5V*3 4：Standby power：0.015mW 5：Standby current：3uA 6：Working current：200uA 7：Emission current：10mA 8：Remote control distance：about 20m 9：Standby time：6 month 2. Software technical parameters 1：Name：Magic Color 1.
3. Controller technical parameters 1：Working voltage: DC5--24V 2：Output control: can flexible control 3 channel, 2 channel, 1 channel LED lamps. 3：Output current: 4A*3 4：Connect mode: common anode 5：Packing dimension: L215*W165*H55(mm) 6：External dimension: L107*W65*H30（mm） 7：Net weight: 340g 8：Gross weight: 480g 9：Receiving sensitivity: 802.11b DSSS(-5dBm)，802.11b CCK (-10dBm)，802.11g OFDM (-15dBm) III. Magic Color Instruction 1.
5) Open application 1. On Off key 2. color disk 3. mode key 4. speed/brightness bar 5. RGB mode LED control window 6. Cold white and warm white mode LED control window 7. Dimmer mode LED control brightness window 8. Magic Color software setting window Following is control color temperature and brightness two mode page: CT mode page DIM mode page (cold warm white mixed mode) (dimmer mode) www.ledxon.
1. IOS version install method: (not escape or escape all can suit) can enter "app store" search Magic Color. Then it can find our software (below scheme just limit after escape) or open itunes, make our installation package Dragged into itunes, as picture Installation complete click click to install. , open application (same with Android version). www.ledxon.
2. Connect WiFi network If you open Magic Color 1.0 show like below picture: prompt to choose "OK", jump to WiFi setting interface connect WiFi LED controller. Or choose "cancel" don't jump,then setting SIMULATION is ON, it will change to do not connect controller node, diagram form as below: choose proceed wifi setting window Finished setting, if popup below window: indicate connect succeed open wifi connect setting prompt connect correct wifi equipment 3.
5. Color disk instruction Color disk under 3 mode page, the function is entirely different: under CD mode page is used for adjust color, under CT mode page is used for adjust color temperature, under DIM mode page is used for adjust brightness. 6. CD mode page control function CD mode page is used for control LED product which consist of red, green, blue, under this mode page, every time after touch the mode key "M", the lighten way will change."M" is used for setting LED dynamic effect.
IV. LED-WiFi Controller Function Instruction 1. Working state instruction Indicator light Power Wifi Link RF Function table Power indicator light, long-time bright shows power supply normally Free time long-time bright, have wifi data enter flicker, configuration wifi Ssid off Receive the date, become flicker Have correct wifi date enter flicker, free time die out, have remote then control flicker 2.
3. Connect LED, Power supply port LED port under CD mode page need to connect RGB 3 channel LED equipment, under CT mode page need to connect cold white and warm white 2 channel LED equipment group, under DIM mode page need to connect single color LED equipment. 4.
Touch remote panel have 64 touch button (point), each button function as below: 1、on/off key, any state, can turn on or turn off controller output; 2、pause key, under dynamic mode, can make the controller stop current state; 3、this key have 2 function: ①mode add key, so when the current control mode is pulley mode(color), if it need to realize the mode(color) in controller, can press this button.
This key have 2 function: ① pulley static color choose button, so when the current control mode is M key mode(color), if need to realize the static color on pulley, can press this button. ② pulley color switch key: can switch from 55 static color (pulley shows color).
2. The mode form of color temperature control: Mode number function 1 CW 2 80%CW 3 60%CW 4 40%CW 5 20%CW 6 PW(pure white) 7 20%WW 8 40%WW 9 60%WW 10 80%WW 11 WW remark Brightness adjustable 3. The mode form of dimming Control: Mode number function 1 1% 2 10% 3 20% 4 30% 5 40% 6 50% 7 60% 8 70% 9 80% 10 90% 11 100% remark Brightness proportion www.ledxon.
V. Explain installed hardware 1. Install ANT ANT's installation drawing: clockwise install WIFI antenna and anticlockwise take down the antenna. 2. Install power supply and LED equipment This connector structure belong to drawer structure, the device interface of power supply and LED is together, four interface one the left side （3、2、1、V+）is connect led equipment, the fifth interface is connect the anode V+ of power supply, the sixth interface is connect the cathode V_ of power supply.
3. Connect three channels LED instruction When connect three channels LED, you should put the Dream Color software switch to CD mode to use,only under this mode,you can control the LED's color,brightness and speed. Color disk adjust the color(Adjust process can be seen in the upper left corner R, G, B numerical with change),speed/brightness item adjust speed and bright("M"set the LED dynamic effect,"M"adjust the LED dynamic change. 4.
5. Connect one channel LED instruction When connect three channels LED, you should put the Dream Color software switch to CD mode to use,under this mode,use color disk control the LED's brightness,Adjust process can be seen in the upper left corner NM numerical with change. VI. FAQ 1. Magic Color can`t open (error and breakdown), how to do? Answer: If it is happened, just need to open again then you can solve.
