Instruction Manual

ManualsBrandsLEDALITE ManualsLinear LightLEDALITE ID-23 Drywall Trim PoE TruGroove Recessed Micro Linear Light

Rev C. www.ledalite.compage6/9/2022 1

Linear

ID-23 Drywall Trim PoE

TruGroove Recessed Micro

System Overview

These instructions review how to install drywall trim versions of TruGroove recessed micro fixtures for power over ethernet application.

Please refer to layout drawings supplied by Philips Ledalite in conjunction with these installation instructions. The graphic below shows

the components required to install a run of TruGroove recessed micro fixtures in drywall ceilings.

ATTENTION: Install in accordance with local and national building and electric codes.

Suspension Cable

Mounting Kit 390ZA01

Tools: Phillips screwdriver, 5/16” Nut Driver

Joint Kit

Brackets

• Joiner Aligners (x2)

• Joining Brackets (x2)

• Hex Bolts (x4)

• Screw(s)

( x1 symmetric, x2 for asymmetric )

• LED pan connectors (x1)

NOTE: Image shown is a symmetric

connector. Asymmetric has two pieces.

NOTE: One (1) kit required for each module

joint in continuous runs

Exterior lens kits

- variable lengths

Module 2

Module 1

Summary of content (8 pages)

PAGE 1
Linear TruGroove Recessed Micro ID-23 Drywall Trim PoE System Overview These instructions review how to install drywall trim versions of TruGroove recessed micro fixtures for power over ethernet application. Please refer to layout drawings supplied by Philips Ledalite in conjunction with these installation instructions. The graphic below shows the components required to install a run of TruGroove recessed micro fixtures in drywall ceilings.
PAGE 2
ID-23 TruGroove Drywall Trim Installation Instructions This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interreference when the equipment is operated in a commercial environment.
PAGE 3
ID-23 TruGroove Drywall Trim Installation Instructions Prepare Ceiling: Continuous Runs 2 • Determine Locations B Ceiling Cut-out Details Determine fixture location and fixture type. Refer to figure B for mount locations and cut-out length. Install mount brackets and suspension cables as shown below. • FIXTURE LENGTH Min Determine power feed location(s) refer to layout drawings. Install power feeds as required and drop below installed ceiling height.
PAGE 4
ID-23 TruGroove Drywall Trim Installation Instructions Install fixtures 6 Prepare Fixtures 7 Insert Aircraft Cable 8 Arrange boxed fixtures on floor in specified mounting locations, based on supplied layout drawings. Match up each fixture based on the spec tag and ID number labelled on each fixture box for the specified run. 9 Install CAT6 Cable Raise Fixture 12” 12” Suspend each module by inserting the aircraft cables through the grippers on top of the housing.
PAGE 5
ID-23 TruGroove Drywall Trim Installation Instructions NOTE: For Standalone fixtures skip to step 15 12 Join Individual Modules Gently slide housing modules together, ensuring joiner aligners are engaged inside the trim in the adjacent module. Important: Joiner aligners must be fully inserted to provide proper section alignment. 15 Raise Fixture(s) into Ceiling Cut-out 13 Open Slots for Joiner Bracket Snap off the safety cover on joiner bracket slots with a flat head screwdriver.
PAGE 6
ID-23 17a TruGroove Drywall Trim Installation Instructions Led Pan Joiner - Symmetric Mount the LED pan connector with the supplied screw in the joiner kit. 18 17b Led Pan Joiner - Asymmetric Mount the LED pan connector with the supplied screw in the joiner kit. There are two pieces for the asymmetric fixture Install Lens Lens Removal for maintenance: To remove snap-in lens for maintenance purposes, insert a flat, smooth edged object between lens and housing.
PAGE 7
ID-23 TruGroove Drywall Trim Installation Instructions Sensors in Rows Single Sensor Controlling Whole Row 1. Purple & brown (or purple & grey/pink) control wires MUST be connected between fixtures. Note: • A maximum of 8 drivers can be wired to one sensor; confirm fixture driver count with factory. 1 Integral Sensor Alternate Remote Sensor Bottom view of fixtures 4ft 8ft Multiple Sensors Controlling Separate Zones in a Row 2.
PAGE 8
ID-23 TruGroove Drywall Trim Installation Instructions Occupancy Sensor Coverage: Note: Longer dimension of detection area (Y1, Y2) is parallel to longer dimension of the luminaire. The detection area for the movement sensor can be roughly divided into two parts: • Minor movement (person moving ≤3ft/s or 0.9m/s). • Major movement (person moving ≥3ft/s or 0.9m/s).