User Manual

ManualsBrandsLED BTF- lighting ManualsEnergy SavingRGB LED Strip SMD5050, WS2811 (black, with controls, IP67, 12 V, 60 LEDs/m, 5 m)

WS2811

Signal line 256 Gray level 3 channal

Constant current LED drive IC

http://www.world-semi.com

Feature

l Output port compression 12V .

l Built in stabilivolt, Only add a resistance to IC

VDD feet when under 24V power supply.

l Gray level 256 can be adjusted and scan freque

ncy not less than 400Hz/s.

l Built in signal reshaping circuit,after wave resha-

ping to the next driver, ensure wave-form distor-

tion not accumulate.

l Built-in electric reset circuit and power lost reset

circuit.

l Cascading port transmission signal by single lin-

l Any two point the distance more than 10m tran-

smission signal without any increasecircuit.

l When the refresh rate is 30fps, low speedmodelc

ascade number are not less than 512 points, hig-

h speed mode not less than1024 points.

l Send data at speeds of up to 400 Kbps and 800

Kbps two patterns.

Applications

l LED decorative lighting.

l Indoor/outdoor LED video or irregular screen.

General description

The WS2811 is 3 output channels special for LED driver circuit. It internal include intelligent digital port

data latch and signal reshaping amplification drive circuit.Also include a precision internal oscillator and a 12V

voltage programmable constant current output drive. In the purpose of reduce power supply ripple, the 3 outp-

ut channels designed to delay turn-on function.

IC use single NZR communication mode.After the chip power-on reset, the DIN port receivedata from con

troller, the first IC collect initial 24bit data then sent to the internal data latch, theother data which reshaping

by the internal signal reshaping amplification circuit sent to the next cascade IC through the DO port. After

transmission for each chip,the signal to reduce 24bit. IC adopt auto reshaping transmit technology, making the

chip cascade number is not limited the signal transmission, only depend on the speed of signal transmission.

The data latch of IC depend on the received 24bit data produce different duty ratio signal at OUTR,

OUTG, OUTB port. All chip synchronous send the received data to each segment when the DIN port input a

reset signal. It will receive new data again After the reset signal finished. Before a new reset signal received,

the control signal of OUTR ,OUTG , OUTB port unchanged. IC sent PWM data that received justly to OUTR,

OUTG , OUTB port, after receive a low voltage reset signal the time retain over 50us. We offer two package

SOP8 and DIP8.

Summary of content (7 pages)

PAGE 1
WS2811 Signal line 256 Gray level 3 channal Constant current LED drive IC Feature Applications l l l l l l l l l l l Output port compression 12V. Built in stabilivolt, Only add a resistance to IC VDD feet when under 24V power supply. Gray level 256 can be adjusted and scan freque ncy not less than 400Hz/s. Built in signal reshaping circuit,after wave reshaping to the next driver, ensure wave-form distortion not accumulate. Built-in electric reset circuit and power lost reset circuit.
PAGE 2
WS2811 Signal line 256 Gray level 3 channal Constant current LED drive IC PIN configuration PIN function NO.
PAGE 3
WS2811 Signal line 256 Gray level 3 channal Constant current LED drive IC Electrical Characteristics（TA=-20～+70℃，VDD=4.5～5.5V,VSS=0V,unless otherwise specified） Prameter Smybol conditions Min Tpy Max Unit Low voltage output current IOL ROUT —— 18.5 —— mA Idout Vo=0.4V，DOUT 10 —— —— mA Input current II VI=VDD/VSS —— —— ±1 µA VIH DIN，SET 0.7VDD —— —— V VIL DIN，SET —— —— 0.3 VDD V VH DIN，SET —— 0.
PAGE 4
WS2811 Signal line 256 Gray level 3 channal Constant current LED drive IC D1 Sequence chart: 0 co d e T0 L T0H D2 DIN DO DIN DO IC 1 IC 2 D3 D4 DIN DO IC 3 T1L 1 cod e T1 H Treset R ET co d e Cascade method: reset code >=50us Data refresh cycle 1 D1 first 2 4 b it Data refresh cycle 2 seco n d 2 4 b it th ird 2 4 b it seco n d 2 4 b it D2 reset code first 2 4 b it th ird 2 4 b it seco n d 2 4 b it th ird 2 4 b it seco n d 2 4 b it th ird 2 4 b it th ird 2 4 b it D3 th ird 2 4
PAGE 5
WS2811 Signal line 256 Gray level 3 channal Constant current LED drive IC Typical application circuit: 1.power supply is 5V with 1 LED and constant current (18.
PAGE 6
WS2811 Signal line 256 Gray level 3 channal Constant current LED drive IC Package imformation: DIP-8 Package: Symbo l Dimensions In Millmeters Min Nom Max Min Nom Max A — — 4.31 — — 0.170 A1 0.38 — — 0.015 — — A2 3.15 3.40 3.65 0.124 0.134 0.144 B 0.38 0.46 0.51 0.015 0.018 0.020 B1 1.27 1.52 1.77 0.050 0.060 0.070 C 0.20 0.25 0.30 0.008 0.010 0.012 D 8.95 9.20 9.45 0.352 0.362 0.372 E 6.15 6.45 6.65 0.242 0.252 0.262 E1 — 7.62 — — 0.
PAGE 7
WS2811 Signal line 256 Gray level 3 channal Constant current LED drive IC SOP-8 Package: Symbol Dimensions In Millmeters Dimensions In Inches Min Max Min Max A 1.350 1.750 0.053 0.069 A1 0.100 0.250 0.004 0.010 A2 1.350 1.550 0.053 0.061 b 0.330 0.510 0.013 0.020 c 0.170 0.250 0.006 0.010 D 4.700 5.100 0.185 0.200 E 3.800 4.000 0.150 0.157 E1 5.800 6.200 0.228 0.244 e 1.270 0.050 L 0.400 1.270 0.016 0.050 θ 0º 8º 0º 8º http://www.world-semi.