User's Manual

ManualsBrandsLectrosonics ManualsPro AudioSRc5P Dual-Channel Slot-Mount ENG Receivers

UHF Digital Hybrid Wireless

Rio Rancho, NM

Menu Item Descriptions

LEVEL

This setup screen displays the audio output level of the

receiver in dBu when the transmitter is fully modulated.

Press the MENU/SEL button to toggle between receiver

1 and receiver 2. Use the UP or DOWN buttons to

change the level. Range is from -50 to +5 dBu in 1 dB

steps. Press the BACK button to leave this screen.

The output levels at the two jacks may be set indepen-

dently, regardless of the diversity mode setting.

DEFAULT

Restores the factory default settings.

LOCALE (Band C2 units only)

The LOCALE setup screen has two settings, “--” and

“JA”. If “JA” is selected, C2 band coverage stops at

713.9 MHz. If “--” is selected, C2 band coverage goes

all the way to 716.775 MHz.

SMARTUNE

See the section entitled Finding Clear Frequencies

with SmartTune

IR SYNC

Navigate to this menu item to manually initiate the IR

sync transfer. Hold the IR ports on the transmitter and

receiver facing each other a foot or two apart and press

the UP arrow for channel 1 or the DOWN arrow for

channel 2. Watch for a conﬁrmation on the transmitter

LCD to verify the settings were correctly transferred. If

one or both settings could not be enabled on the trans-

mitter, an error message will appear on its screen.

SCAN

See the section entitled Finding Clear Frequencies

with Manual Scanning.

DIVMODE

The SWITCH diversity mode (dual channel mode) al-

lows the two internal receivers to operate independently

on different frequencies and settings with two different

transmitters. Diversity reception uses an antenna phase

switching technique on each receiver. When this mode

is selected, the setup screens will prompt you to select

the receiver to be adjusted.

The RATIO mode combines the two internal receiv-

ers to pick up the same transmitter and mix their audio

outputs in a ratio panning mode. In this mode, the setup

screen for frequency will prompt you for a single value

which will automatically be set for both receivers.

TALKBACK

This is a special function that re-directs the audio output

of the transmitter in use to the channel 2 output when

a button is pressed on the transmitter. The normal use

is to provide a “com” channel so the person using the

transmitter can have a direct line to the crew or produc-

tion staff that is not sent to the program output. The

HHa hand held transmitter provides a programmable

switch on the housing that can be conﬁgured for this

function.

Button

(none)

Mute

Ta lkBk

Programmable button

As long as the button

is held in, the audio

will appear at the

channel 2 output.

When the button is

released, the audio

output will switch

back to channel 1.

To enable this mode,

simply select Talk-

back in the menu and use the UP and DOWN arrow

buttons to turn the function on. The mode must also be

enabled on the transmitter.

Talkback works the same way in either the SWITCHED

or RATIO diversity modes, but ONLY works in the HY-

BRID compatibility modes.

NOTE: When Talkback is enabled, only receiver 1 and

a blinking TB will appear in the Main Window.

COMPAT

Compatibility modes adjust the FM deviation and audio

processing (companding) to match other Lectrosonics

models and some models from other manufacturers.

NA HYBR North American Digital Hybrid Wireless

NU HYBR ETSI compliant Nu Digital Hybrid Wireless®

MODE 3 Other manufacturer*

200 SER 200 Series transmitters

100 SER 100 Series transmitters

JA MODE3 Japan Other manufacturer*

JA HYBR Japan Digital Hybrid Wireless

MODE E Other manufacturer*

EU HYBR European Digital Hybrid Wireless

300 SER 300 Series transmitters (European)

MODE 7 Other manufacturer*

MODE 6 Other manufacturer*

IFB SER Standard IFB mode

NOTE: Make certain the COMPAT mode is set to

match the mode in the transmitter for optimum audio

quality. If the modes are not matched, the audio will be

distorted or noisy, or there may be no audio at all.