User's Manual

Operation: RadioPopper PX Transmitter - QUICK REFERENCE
Power On / O - Press and hold the Power Button for one second. Green LED on indicates “power on”, Green LED o
indicates “power o”.
Enter Menu Mode - Tap the “X” button one time to enter Menu Mode. Once in Menu Mode, you will move to the
next menu each time the “P” button is pressed, and you will adjust the setting of the current menu by pressing the “X”
button.
IMPORTANT NOTE!!! When in Menu Mode, the radio will NOT be active for normal operation. If you attempt to
activate the system by taking a shot on your camera while in Menu Mode, the PX Transmitter will not send any radio
signals. Similarly, the PX Receiver will not receive or respond to any radio signals while in Menu Mode. To exit Menu
Mode and resume normal operation, press the “P” button repeatedly until the Digital Display goes dark. You should
also observe the Link LED strobe momentarily which indicates the radio has been reset and is in normal operating
mode.
“b” - Battery Level - A full set of batteries reads “b9”, a dead set reads “b1”. Level will decrement as battery power is
used. You may quickly exit the Battery Level screen and imediately return to normal operating mode by tapping the
“X” button once while viewing the battery level. This makes quickly checking the battery level easy by simply tapping
the “X” button twice - once to view the level, and once again to quickly resume normal transmitting operation.
“L1, L2, L3” - Remote power level setting. In this mode you may tick the power level settings of up to three groups
of remote slave devices up and down in steps from 01 to 32. Setting of “00” will cause the remote ash to not re. Tap
the “X” button to increment. While pressing the “X” button, tap the “P” button to decrement.
“Ch” Radio Channel - Shows the current radio channel between 01 and 16. Tap the “X” button once to view the
current channel without changing it. Each successive tap of the “X” button will increase the channel, with 16 looping
back to channel 01. When the desired channel is set, press the “P” button to lock in the channel and move to the next
menu item.
Operation: RadioPopper PX Receiver - QUICK REFERENCE
Power On / O - Press and hold the Power Button for one second. Green LED on indicates “power on”, Green LED o
indicates “power o”.
Enter Menu Mode - Tap the “X” button one time to enter Menu Mode. Once in Menu Mode, you will move to the
next menu each time the “P” button is pressed, and you will adjust the setting of the current menu by pressing the “X”
button.
Operation: Detailed PX Transmitter Operating Instructions
Power On / O - Press and hold the Power Button for one second. Green LED on indicates “power on”, Green LED o
indicates “power o”.
Enter Menu Mode - Tap the “X” button one time to enter Menu Mode. Once in Menu Mode, you will move to the
next menu each time the “P” button is pressed, and you will adjust the setting of the current menu by pressing the “X”
button.
IMPORTANT NOTE!!! When in Menu Mode, the radio will NOT be active for normal operation. If you attempt to
activate the system by taking a shot on your camera while in Menu Mode, the PX Transmitter will not send any radio
signals. Similarly, the PX Receiver will not receive or respond to any radio signals while in Menu Mode. To exit Menu
Mode and resume normal operation, press the “P” button repeatedly until the Digital Display goes dark. You should
also observe the Link LED strobe momentarily which indicates the radio has been reset and is in normal operating
mode.
“b” - Battery Level - A full set of batteries reads “b9”, a dead set reads “b1”. Level will decrement as battery power is
used. You may quickly exit the Battery Level screen and imediately return to normal operating mode by tapping the
“X” button once while viewing the battery level. This makes quickly checking the battery level easy by simply tapping
the “X” button twice - once to view the level, and once again to quickly resume normal transmitting operation.
“L1, L2, L3” - Remote power level setting. In this mode you may tick the power level settings of up to three groups
of remote slave devices up and down in steps from 01 to 32. Setting of “00” will cause the remote ash to not re. Tap
the “X” button to increment. While pressing the “X” button, tap the “P” button to decrement.
“Ch” Radio Channel - Shows the current radio channel between 01 and 16. Tap the “X” button once to view the
current channel without changing it. Each successive tap of the “X” button will increase the channel, with 16 looping
back to channel 01. When the desired channel is set, press the “P” button to lock in the channel and move to the next
menu item.
NOTE: It may take several seconds for sleeping PX Receivers to come out of sleep and re-aquire the signal.
Timer Reset - Take a shot (activate the ash) or tap the Link Button to reset the 7 minute sleep timer. Link LED will
strobe momentarily indicating button press.
RadioPopper PX Radio Wireless System
Page 16
Operating Instructions
Page 17