. LEADTEK Wireless GPS Receiver User’s Manual GPS 9537 Version 1.
. Contents 1. INTRODUCTION ...........................................................................................................................1 1.1. 1.2. 2. OVERVIEW .................................................................................................................................1 M AIN FEATURES ........................................................................................................................1 TECHNICAL SPECIFICATIONS.........................................
. ii
. 1. Introduction 1.1. Overview The Leadtek 9537 Wireless GPS receiver is a Global Position System Receiver with Bluetooth wireless technology. This wireless GPS receiver allows you to receive GPS data on mobile handheld wirelessly. By sending GPS position data over Bluetooth, you can position the receiver for the best possible reception all without wires. The advent of wireless GPS receiver will become the next level of GPS receivers.
. C/A code Channels Antenna Type 1.023 MHz chip rate 12 channel all-in-view tracking Built-in Ceramic patch antenna (External antenna optional) 2.1.2 Accuracy Position Velocity Time 10 meters, 2D RMS 0.1 meters/second 1 microsecond synchronized to GPS time 2.1.3 Datum Default WGS-84 2.1.4 Acquisition Rate (Open sky, stationary requirement) Reacquisition Snap start Hot start Warm start Cold start 0.1 sec., average 2 sec., average 8 sec., average 38 sec., average 45 sec., average 2.1.
. Continuous mode 95~105 mA Current consumption Remark Trickle-power mode 15--5sec -->65mA 65--1sec-->15mA 98~108mA 65~75mA 1. Battery is not charging state. 2. The current consumption of active antenna is 21mA Typical Operation Typical use 6- 8 hours GPS and Bluetooth fully active 4.5 - 6 hours 2.1.7 Main Interface Connection: Protocol messages Communication via Bluetooth Serial Port Profile(SPP) NMEA-0183 Version 2.
. AC plugs provided for US, UK and Europe. 2.5. Regulatory Standards Operational Safety Electrical BQB CE FCC Class B, ICES-003 Class B, E-Mark 3. Applications Leadtek GPS 9537 Bluetooth GPS receiver is a high performance, low power consumption product. The product applications are as follow. u Vehicle Tracking & Location-based Services u Personal/Portable Navigation u Car Navigation u Marine Navigation 4. Operation 4.1.
. The Bluetooth GPS has two LED light which each has two colors. One is GPS & Charge status LED, that is named LED 2, and the other is Bluetooth & low power status LED, that is named LED 1.
. 4.2. Turn on/off Turn on Turn off To turn on the receiver, press the power button on the topside briefly (0.5 seconds). The left LED(LED 2) indicator will flash briefly. The right LED (LED 1) indicator will start flashing. To turn off the receiver, press the power button on the topside for 3 seconds. The LED indicator will flash briefly before switching off the receiver. 4.3. Charging Low Power Charging The right LED(LED 1) indicator will turn RED (normally BLUE) when battery power becomes low.
. u The Leadtek BT GPS receiver u A power supply u Three adapters for the power supply u A power supply of CLA(cigarette lighter adapter) 6. Notices 6.1. Global Positioning System The Global Positioning System (GPS) is operated and maintained by the Government of the United States of America who are responsible for the availability and the accuracy of the system. Changes in the operation, availability and accuracy may affect the operation of your GPS receiver. 6.2.
. 6.4. Important The information in this document is subject to change without notice. No liability shall be assumed for technical or editorial errors or omissions contained herein; nor for incidental or consequential damages resulting from the performance or use of this material. This document contains information protected by copyright. 6.5 Battery This product uses a Lithium-Ion battery. Please charge fully before first use.
. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Appendix A Software Install iPAQ Bluetooth Setup with Pocket PC software These steps apply to the PDA with Bluetooth function, for example iPAQ 3870 or 3970 PDA The operation system of iPAQ Pocket PC is Chinese Window CE version and shows as follow. The English version should be similar with Chinese.
. <2> Click the Bluetooth RF icon and select Bluetooth manager. <3> Click tool and select setup the device.
. <4> Select the serial port panel and you can see the output serial port which should be used by application for specified Bluetooth device.
. Connections are initiated from the client: <1> Click search to find available device. <2> Select the device which you want to establish connection to and then click save button. Another window will popup and you can choose at least one place to save the selected device. After that, click OK. <3> Click the device you want to establish connection to. The device information will show and at the same time iPAQ Bluetooth will search for available service in the selected device for a short time.
. any service found you can click action and select connect to the found service. Appendix B Installing WinFast Navigator for Pocket PC Note : Microsoft ActiveSync has to be installed on your computer when you install WinFast Navigator. The application interface is shown in the figure to the right. Step 1. Insert the software CD in your CD-ROM drive. The setup screen appears as shown in the figure to the right. If the setup screen does not appear automatically, run install.exe on the CD.
. initialize the installation. Step 2. The Add/Remove Programs dialog box appears. An information box on top of it tells you the application is Retrieving application data from the mobile device. Step 3. The application will next determine the destination location. A dialog box appears asking if you want to install the application at the default location, which is Main Memory on your PDA/pocket PC. Click Yes to install WinFast Navigator at that location.
. one as desired and then click OK. Step 4. A dialog box appears showing the progress of installation.
. Step 5. When the installation is completed, a dialog box tells you to check your mobile device screen to see if additional steps are necessary to complete this installation. Click OK.
. Appendix C Test Reference for Only PC Bluetooth Setup with Widcomm BTW This software does belong to copyright reserved of Widcomm company - 17 -
. and you have to get the authorized software to use it. The follow method is only for reference. The Bluetooth Serial Port service allows two Bluetooth devices to establish a wireless connection through virtual communications ports and then use that connection as if it were a hardwired serial cable between the devices.
. <2> In the right pane of Entire Bluetooth Neighborhood, right-click anywhere except on a device name and select Refresh from the pop-up menu.
. <3> In the Folders pane of My Bluetooth Places, right-click the server you want to establish a connection with and select Discover Available Services from the popup menu to update the available services list. The available services will be displayed in the right pane of My Bluetooth Places. <4> In the right pane of My Bluetooth Places, double-click Bluetooth Serial Port. A dialog box appears that contains the communications port number assigned to this connection by the client.
. To close a Bluetooth serial port connection Connections are normally closed from the client: l On the client, in the Folders pane of My Bluetooth Places, select (highlight) the device that is providing the Bluetooth Serial Port service. l In the right pane of My Bluetooth Places, right-click Bluetooth Serial Port and then select Disconnect Bluetooth Serial Port from the pop-up menu.
. Leadtek Research Inc.: Leadtek U.S.A.: Leadtek Research Europe B.V.： 18F, 166, Chien-Yi Rd., Chung Ho, Taipei Hsien, Taiwan (235) Phone: +886-(0)2 8226 5800 Fax: +886-(0)2 8226 5801 46721 Fremont Blvd., Fremont, CA94538, U.S.A. Phone: +510 490 8076 Fax: +510 490 7759 Antennestraat 16 1322 AB, Almere – The Netherlands Tel:+31(0)36 536 55 78 Fax:+31(0)36 536 22 15 E-mail: service@leadtek.com.tw Home Page: www.leadtek.com.
