Instruction Manual

1.
•
•
•
•
**
2.
•
MADE IN CHINA
INSTRUCTIONS:
Wireless Charging Function:
Remove the 3-in-1 charging cable(3) out
from the cable storage compartment of the
wireless charging pad.
Once removed, connect the USB input
tip(4) to the appropriate power source and
the 2-in-1 charging tip(5) to the Micro-USB
input port(8) of the wireless charging pad.
Once connected, the LED indicator will glow
WHITE, then light off to indicate in standby
mode and is ready to begin charging.
Place the wireless charging supported
device on the charging surface(1),the
device will begin to charge automatically.
(LED will glow WHITE when device is
charging).
Note: When wireless charging, if the LED
is either NOT a wireless charging device
or there is an object between the device
and charging surface interfering with the
charging process.
Wireless Charging Pad - Phone Stand:
As shown below the wireless charging pad
is able to be fold open to be used as a
wireless charging phone stand.
Roche Multifunctional
Wireless Charging Stand
Instruction Manual
7141-73
1 x Wireless Charging Stand
1 x Instruction Manual
1 x 3-in-1 Charging Cable
Input power: 5V/2A
Micro-USB input: 5V/1A
Wireless Charging Output: 5V/1A
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
•
•
•
Wireless Charging Surface
Foldable Phone Stand
3-in-1 Charging Cable
USB Input Tip
2-in-1 Charging Tip
Type-C Charging Tip
LED Indicator
Micro-USB Input Port
Charging Cable Storage Compartment
LED Flashlight
What’s included:
Features:
This device complies with Part 15 of the
FCC Rules. Operation is subject to the
following two conditions:
This device may not cause harmful
interference, and
This device must accept any interference
received, including interference that may
cause undesired operation.
Warning:
approved by the party responsible for
compliance could void the user’s authority
to operate the equipment.
(1)
(2)
*
FCC Statement:
phone before charging on this device.
WARNING-When using this product, basic
precautions should always be followed:
Read all the instructions before use.
Never store or use this product in
temperatures below 32°F (0°C) or above
115°F (45°C).
Do not overcharge your phone. The
unit may become hot under excessive
use. Remove your phone once it is fully
charged. Never charge your phone for
more than 7 hours at a time.
To reduce the risk of injury, close
supervision is required when the product is
used near children.
Do not expose the device to moisture.
Do not use the device in excess of its
output rating. Overload outputs above the
Do not use the device if damaged or
explosion or risk of injury.
Do not disassemble the device. For
professional. Incorrect reassembly may
or temperatures above 104°F (40°C) may
result in explosion.
To ensure product safety, ensure that
identical replacement parts.
Attachments on the back of your phone
wireless charger, and lead to overheating.
Please remove attachments from the
•
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
SAFETY PRECAUTIONS:
11
10
FCC
Warning Statement
The distance between user and products should be no less than 20cm
Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate
the equipment. This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This
equipment generates uses and can radiate radio frequency energy and,
if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or
more of the following measures:
‐ Reorient or relocate the receiving antenna.
‐ Increase the separation between the equipment and receiver.
‐ Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
‐ Consult the dealer or an experienced radio/TV technician for help.