User manual

Littfinski DatenTechnik (LDT)
Operating Instruction
Connection Cable (2m)
for the s88-feedback bus and the PC-light control
Light@Night
from the Digital-Professional-Series!
Kabel s88 2m Part-No.: 000101
Kabel Light@Night 2m Part-No.: 000101
The interference protected twisted connection cable
of 2 meter length can be used for:
⇒ extending the installation distance of all LDT s88
components or directly to the command station /
interface or to each other (for RM-88-N, RM-88-N-O,
RM-GB-8-N only).
⇒ connecting s88 feedback module from Märklin /
Viessmann directly together at a distance of 2
meter or extend the installation at 2 meter distance
each.
⇒ connecting the Display and Power Module of the
PC-Light control Light@Night to each other.
This product is not a toy! Not suitable for children under 14 years of age! The kit
contains small parts, which should be kept away from children under 3 years of
age! Improper use will imply danger of injuring due to sharp edges and tips!
Please store this instruction carefully.
CE Part-No.:
24 00 09
Introduction / Safety Information:
You have purchased a connection cable for your digital model
railway.
The connection cable is a high quality product which is supplied
within the assortment of Littfinski DatenTechnik (LDT).
We are wishing you having a good time using this product.
The connection cable comes with 24 month warranty.
• Please read the following instructions carefully. Warranty will
expire due to damages caused by disregarding the operating
instructions. LDT will also not be liable for any consequential
damage caused by improper use or installation.
• Attention: Please switch off your model railway by
disconnecting the transformers from AC-current before
starting any installation.
Description for Kabel s88:
The s88 connection cable consists of a 2 meter twisted bus
cable with two original s88 pin-socket connectors. At one socket
is a pin-pin plug inserted.
2 m
Stiftleiste
pin plug
rosa
pink
rosa
pink
If you want to use the s88 connection cable for connection of
the feedback module RM-88-N, RM-88-N-O or RM-GB-8-N you
have to remove at first the pin-pin plug.
Attach now one socket in that position onto the 6-poles pin bar
of the feedback module that the single white wire
corresponds with white marking at the pin bar.
Please attend to the marking at the pin bar “OUT” and “IN” in
accordance to the operation instruction of the feedback module.
8-fach Rueckmeldemodul
mit Gleisbesetztmeldern
8-fold feedback module
with occupancy detectors
RM-GB-8-N
Rev. 1.0
BU1
BU2
s88-N
OUT
IN
s88-N
weiß
ST1
OUT IN
ST2
Attach the second pin-socket of the bus-cable directly to the
command station or to the interface respectively to an other
feedback module within the feedback line.
If you want to use the
s88 connection cable
for connecting two
Märklin or Viessmann
feedback module
together please
remove first the pin-
plug.
Insert the pin-socket
connectors of the
connection cable into
the feedback module
that the cable is
directed to the bottom.
To assure a constant
orientation has the
white single wire to be
located into the
direction to the middle
of the feedback
module.
weiss
white
weiss
white
8 7 6 5 4 3 2 1
9 10 11 12 13 14 15 16
märklin
digital
decoder s 88
8 7 6 5 4 3 2 1
9 10 11 12 13 14 15 16
märklin
digital
decoder s 88
2 m
Verbindungskabel
connection cable
The following draft shows an assembled s88 connection cable
shown from the left side.
rosa
pink
rosa
pink
decoder s88
If you want to extend the
s88 bus-connection of
LDT feedback module
RM-DEC-88(-O) or RM-
GB-8 by 2 meters please
leave the pin-pin plug bar
inserted at the plug
connector.
The draft shown at the
right indicates how to
extend a 75cm s88 bus-
cable of a feedback
module RM-DEC-88 by 2
meters.
Attend to the correct
orientation of the bus
connectors to assure that
the cable colors of the
single wires correspond
exactly.
Stiftleiste 6 pol.
pin-pin plug 6 poles
weiss
white
weiss
white
Verbindungskabel
connection cable
L ittfinski D aten T echnik
D-25492 Heist
www.ldt-infocenter.com
10
9
11
8 7 6 5 4 3 2 1
12 13 14 15 16
Peter Littfinski DatenTechnik
Rueckmeldedecoder RM-DEC-88
16-channel feedback modul
Rev. 3.0
rosa gelb
gruen
braun weiss grau
INOUT
ST1
ST2
Digital-Profi werden!
16 Rückmeldeeingänge für den
s88-Rückmeldebus.
Rückmeldemodul
RM-DEC-88