OPERATOR’S INSTRUCTION MANUAL DIGITAL CLAMP METER MODEL: DT2015A WARNING READ AND UNDERSTAND THIS MANUAL BEFORE USING THE INSTRUMENT.
1. INTRODUCTION This manual provides all safety information, operation instruction, specifications and maintenance for the meter, which is compact, handheld, and battery operated. This instrument performs AC/DC voltage, AC Current, Resistance, Audible Continuity, Diode and Temperature measurements ect.. It is a 3 5/6 digits, 6000 counts auto ranging digital clamp multimeter.
magnetic field. The performance of the Meter may deteriorate after dampened. When using the test leads, keep your fingers behind the finger guards. Disconnect circuit power and discharge all high-voltage capacitors before testing resistance, continuity or diodes. Replace the battery as soon as the battery indicator appears. With a low battery, the Meter might produce false readings that can lead to electric shock and personal injury.
Range select Operation Temperature Storage Temperature Battery Type Dimension(H×W×D) Weight : auto or manual : 0°C to 40°C, less than 80%RH : -10°C to 50°C, less than 85%RH : 1.5V x 3, AAA size : 216×75×35mm : Approx 235g with battery 3. ELECTRICAL SYMBOLS DC (Direct Current). AC (Alternating Current). DC or AC Important safety information. Refer to the manual. Dangerous voltage maybe present. Earth ground.
4.
1. Transformer Jaws Pick up the AC Current flowing through the conductor. 2. Electric torch Illuminate an area of work when it is on. 3. Alarm indicator The indicator is lit when the meter is closer the alive wire. 4. Trigger Press the level to open the transformer jaws when the finger press on the level is released the jaws will close again. 5. Function/ rotary Switch This switch can be used to select desired function and range. 6. Back light button Press the button, backlight is on.
addition. 14. NCV sonsor Can sense the strong electric field, lights the NCV indicator LED. 5. SPECIFICATIONS Accuracy is guarantied for 1 year 23°C±5°C less than 80%RH 5-1. DC VOLTAGE (Auto ranging) Range Resolution Accuracy 600mV 0.1mV ±(0.8% of rdg + 5dgts) 6V 1mV ±(0.8% of rdg + 3dgts) 60V 10mV 600V 100mV ±(1.0% of rdg + 5dgts) Input Impedance: 10MΩ Overload Protection: 600V DC/AC rms Max. Input voltage: 600V DC 5-2.
5-4. RESISTANCE (Auto Ranging) Range Resolution Accuracy 600Ω 0.1Ω 6KΩ 1Ω 60KΩ 10Ω ±(1.5% of rdg + 5dgts) 600KΩ 100Ω 6MΩ 1KΩ 60MΩ 10KΩ Open Circuit Voltage: about 0.25V Overload Protection: 250V DC/AC rms 5-5. Diode and Continuity Range Introduction Remark The approximate forward Open circuit voltage drop will be voltage: about displayed 1.5V The built-in buzzer will Open circuit sound if the resistance is voltage: about less than about 30Ω. 0.
to the “INPUT” jack. Set the function switch to range position. Connect the test leads across the source or load to be measured. 4) Press the SEL button, to select V or V range 5) Read LCD display. The polarity of the RED lead connection will be indicated when making a DC measurement. Note: a. In small range, the meter may display an unstable reading when the test leads have not been connected to the load to be measured. It is normal and will not affect the measurements. b.
6-4. Continuity Test 1) Connect the BLACK test lead to the “COM” jack and the RED to the “INPUT” jack (Note: The polarity of the red test lead is positive “+”). 2) 3) Set the range switch to or range position. Press the “SEL” Button to select continuity measurement mode, and the symbol “ ” will appear as an indicator. 4) Connect the test leads across the load to be measured. 5) If the circuit resistance is lower than about 30Ω, the built-in buzzer will sound. 6-5.
sensor is cut off. c) The limit temperature measured by the thermocouple given together with the instrument is 250°C; 300°C is acceptable within short period. 6-7 NCV test 1. Set the rotary switch to "NCV" position, LCD display "EF ". 2. Close the front end of the clamp to the measured socket. 3. When NCV detects AC voltage between 90v to 10v sound and light alarms at the same time. Distinguish live and neutral wires: Not sound and light alarmed when detecting neutral wire, 4.
8. BATTERY REPLACEMENT If the sign “ ” appear on the display, it indicates battery should be replaced. Remove screws and open the back case, replace the exhausted battery with new batteries (Size AAA, 1.5V x3 or equivalent). 9. ACCESSORIES Owners manual: 1 piece Test leads: 1 pair WARRANTY This Instrument is warranted to be free from defects in material and workmanship for a period of one year.
