Model (PEHU Outdoor Flame Heater Owner’s Manual Read these instructions before lighting this appliance. DANGER If you smell gas: 1. Shut off gas to the appliance. 2. Extinguish any open flame. 3. If odor continues, keep away from the appliance and immediately call your gas supplier or fire department. WARNING Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.
WARNINGS AND CAUTIONS DANGER CARBON MONOXIDE HAZARD This appliance can produce carbon monoxide which has no odor. Using it in an enclosed space can kill you. Never use this appliance in an enclosed space such as a camper, tent or home. WARNING: Improper installation, adjustment, alteration, service or maintenance can cause injury, death or property damage. Read the installation, operating and maintenance instructions thoroughly before installing or servicing this equipment.
WARNINGS AND CAUTIONS NOTE:PLEASE READ THE FOLLOWING SAFETY RULES WARNING: The installation must conform with local codes or, in the absence of local codes, with the National Fuel Gas Code, ANSI Z223.1/NFPA 54, NFPA58 Natural Gas and Propane Installation Code, CSA B149.1, or Propane Storage and Handling Code, B149.2 Any guard or other protective device removed for servicing the heater must be replaced prior to operating the heater. Installation and repair should be done by a qualified service person.
WARNINGS AND CAUTIONS NOTE:PLEASE READ THE FOLLOWING SAFETY RULES WARNING: Within a partial enclosure which includes an overhead cover and three side walls, as long as 30 percent or more of the horizontal periphery of the enclosure is permanently open. The pressure regulator and hose assembly supplied with the appliance must be used, replacement pressure regulators and hose assemblies must be those specified by the appliance manufacturer. This appliance requires 9kg(20lb) LP-gas supply cylinder.
WARNINGS AND CAUTIONS NOTE: PLEASE READ THE FOLLOWING SAFETY RULES: Perform a leak test with a soapy solution: 1. To check gas connections. 2. After connecting a new cylinder. 3. Upon re-assembly after disassembly. This heater is designed to operate with a standard 20 Ib propane cylinder with Approved Cylinder Connection. PREPARATION Before beginning assembly of product, make sure all parts are present. If any part is missing or damaged, do not attempt to assemble the product.
PARTS CONTENTS Please check the contents of the packaging as to whether anything is missing! Chimney cover Weather resistant dome prevents water from entering the combustion zone and reflects heat down. Safety guard protects the full height of the heat exchanger tube. Heat exchange tube has a large heat-radiating surface. Gas control with electronic igniter is centrally positioned for easy access. A hinged metal door is provided for easy access to the LP gas cylinder.
ASSEMBLY INSTRUCTIONS Warning:This appliance requires installation by a competent person. Proper assembly is the responsibility of the installer. Step 1 Step1: To assemble unit-partially open gas chamber door.Carefully lift dome until entire heat exchange tube is exposed. Step 2: After heat exchange tube is fully extended, rotate counter-clockwise until stopped.
ASSEMBLY INSTRUCTIONS Warning:This appliance requires installation by a competentperson. Proper assembly is the responsibility of theinstaller. Step 3 Step3: Insert M6x35 thumb screw into hole A, and M6x12 thumb screw into hole B. Lock the screws. A B Step4: Fully open gas chamber door. Remove knob from door and place on control stem.
ASSEMBLY INSTRUCTIONS Warning:This appliance requires installation by a competent person. Proper assembly is the responsibility of the installer. AA Step 5 + Step5: Place battery incompartment below control panel. AA Battery(1.5V) (not included) Step6: Place the gas cylinder (not included) into the base assembly , and fix it with fixing chain. Attach the regulator to the cylinder, turn clockwise to tighten it securely, and then close the door.
SAFETY CHECK WARNING : ONLY AN AUTHORIZED GAS TECHNICIAN SHOULD INSTALL THIS PRODUCT. Check for leaks All connection on the patio heater have been checked for leakage at the factory. Follow these steps to check the gas hose/regulator/cylinder connections: 1) Make leakage solution by mixing 1 part liquid dish soap and 3 parts water. brush 2) Spoon or brush several drops (or use squirt bottle) of the solution onto hose connection, regulator & cylinder connection. 3) Turn on gas cylinder valve.
OPERATION 1. Ensure control knob is in OFF position. 2. Depress control knob and turn counter clockwise to IGNITE. 3. Continue to depress knob for 30 seconds, listen to ignition pulse. 4. Then, release knob and turn to adjust heat intensit 5. If pilot does not light, turn knob to OFF and wait 5 minutes for gas vapors to dissipate, then repeat steps 2 to 4.
OPERATION Note: The burner may be noisy when initially turned on. To eliminate excessive noise from the burner, turn the control knob to the Minimum position. Then, turn the knob to the level of heat desired. If you experience any ignition problem consult the following “Troubleshooting”. These lighting instructions must be followed. An unsafe condition can occur if they are not followed correctly.
OPERATION 13
LOCATING HEADER FOR USE CAUTION: WHEN CERTAIN MATERIALS OR ITEMS ARE LEFT, ABOVE, BESIDE OR UNDER THIS HEATER WHILE IN USE, THEY WILL BE SUBJECT TO RADIANT HEAT AND COULD BE SERIOUSLY DAMAGED. This heater is primarily used for the heating of outdoor patios, decks, spas, pools and open working areas. Always make sure that adequate fresh air ventilation is provided. Follow the spacing tolerances shown in the following figure right at all times. This heater must be placed on level, firm ground.
MAINTENANCE/STORAGE CLEANING AND MAINTENANCE : To enjoy years of outstanding performance from your heater make sure you perform the following maintenance activities on a regular basis: Keep exterior surfaces clean. Use warm soapy water for cleaning. Never use flammable of corrosive cleaning agents. WARNING: FOR YOUR SAFETY ; DO NOT touch or move heater for at least 45 minutes after use. Allow all burner elements to cool before touching.
MAINTENANCE/STORAGE Spiders and insects can nest in burner or orifices. This dangerous condition can damage heater and render it unsafe for use. Clean burner holes by using a heavy-duty pipe cleaner. Compressed air may help clear away smaller particles. Carbon deposits may create a fire hazard. Clean dome and engine with warm soapy water if any carbon deposits develop. STORAGE: Between uses: Turn the control knob to "OFF" position. Turn LP cylinder to "OFF" position.
TROUBLESHOOTING 17
FIVE-YEAR LIMITED WARRANTY The appliance has been manufactured under the highest standards of quality and workmanship. We warrant to the original consumer purchaser that all aspects of this product will be free of defects in material and workmanship for five (5) year from the date of purchase. A replacement for any defective part will be supplied free of charge for installation by the consumer. Defects or damage caused by the use of other than genuine parts are not covered by this warranty.
