OVERHEAD PATIO HEATER ITE LIM D 5 Y W YEAR AR NT RA UP TO 8 HRS RUN TIME WEIGHTED BASE AUTOMATIC ELECTRONIC IGNITION TILT SWITCH AUTO-SHUTOFF OWNER'S MANUAL PROPANE POWERED P D WWW.LAVAHEAT.
Sorr ento WARNING If you smell gas: 1. Shut off gas to the appliance. 2. Extinguish any open flame. 3. If odor continues, keep away from the appliance and immediately call you gas supplier or fire department. OVERHEAD PATIO HEATER WARNING Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.
WARNINGS AND CAUTIONS DANGER CARBON MONOXIDE HAZARD This appliance can produce carbon monoxide which has no odor. Using it in an enclosed space can kill you. Never use this appliance in an enclosed space such as a camper, tent or home. WARNING: Improper installation, adjustment, alteration, service or maintenance can cause property damage, injury or death. Read the installation, operating and maintenance instructions thoroughly before installing or servicing this equipment.
WARNINGS AND CAUTIONS NOTE:PLEASE READ THE FOLLOWING SAFETY RULES WARNING: The installation must conform with local codes or, in the absence of local codes, with the National Fuel Gas Code, ANSI Z223.1/NFPA 54, NFPA58 Natural Gas and Propane Installation Code, CSA B149.1, or Propane Storage and Handling Code, B149.
WARNINGS AND CAUTIONS NOTE:PLEASE READ THE FOLLOWING SAFETY RULES WARNING: Within a partial enclosure which includes an overhead cover and three side walls, as long as 30 percent or more of the horizontal periphery of the enclosure is permanently open. The pressure regulator and hose assembly supplied with the appliance must be used, replacement pressure regulators and hose assemblies must be those specified by the appliance manufacturer. This appliance requires 9kg(20lb) LP-gas supply cylinder.
WARNINGS AND CAUTIONS NOTE: PLEASE READ THE FOLLOWING SAFETY RULES: PRECAUTIONS Perform a leak test with a soapy solution: 1. To check gas connections. 2. After connecting a new cylinder. 3. Upon re-assembly after disassembly. This heater is designed to operate with a standard 20 Ib propane cylinder with Approved Cylinder Connection. PREPARATION Before beginning assembly of product, make sure all parts are present. If any part is missing or damaged, do not attempt to assemble the product.
EXPLODED VIEW Please check the contents of the packaging as to whether anything is missing! AA BB 1 CC 2 DD 3 4 11 5 6 7 10 8 9 EE 6
PARTS LIST Part # Description Qty 1 Cover 1 2 Head assembly 1 3 Cover fixed plate 1 4 Transom control assembly 1 5 Transom mounting plate 1 6 Pole 1 7 Decorative cover 1 8 Base assembly 1 9 Wheel kit 1 10 Cylinder fixing hook 1 11 1.
ASSEMBLY INSTRUCTIONS STEP 1 Attach wheel kit (9) to base assembly (8) with 2pcs M6 x 20 bolts with 6mm washers and 6mm spring washers (EE). 8 9 Hardware Used EE M 6 x 20 bolt with 6mm washer and 6mm spring washer 2 EE STEP 2 Open the door of base assembly (8). Half-loosen 2pcs M6 x 20 bolts on pole fixing sleeve and insert the pole (6) into the pole fixing sleeve, make sure the shoulder screw on pole sit into the slot on pole fixing sleeve. Then tighten 2pcs M6 x 20 bolts on pole fixing sleeve.
ASSEMBLY INSTRUCTIONS STEP 3 4 Attach cover fixed plate (3) to transom control assembly (4) with 2pcs M4 x 10 bolts (AA). 3 Hardware Used AA M4 x 10 bolt 2pcs AA STEP 4 Attach head assembly (2) to transom control assembly (4) with 4pcs M6 x 14 bolts (CC) at sides first, next 2pcs M6 x 14 bolts (CC) on the top. Caution: Don't fully tighten hardware until entire step is completed. Attach nozzle fixing plate to induct pipe with 2pcs M6 x 14 bolts (CC) and 2pcs M6 nuts (DD) .
ASSEMBLY INSTRUCTIONS STEP 5 Connect the terminals of wires to the terminals of thermocouple, and connect the electrode pin wire to electrode pin as illustration. Caution: no terminal loose after connection. Electrode pin wire Female terminal Male terminal Thermocouple cables female terminals Electrode pin Thermocouple cables male terminals STEP 6 Fix cover (1) to head assembly (2) with 4pcs M4 x 10 bolts (AA) and 4pcs 4mm washers (BB).
ASSEMBLY INSTRUCTIONS STEP 7 Unscrew and take out 1pc M8 x 85 bolt and 1pc M8 cap nut on transom assembly (4) as illustration. 4 M8 x 85 bolt M8 cap nut STEP 8 Half-loosen other 3pcs M8 cap nuts on transom assembly (4).
ASSEMBLY INSTRUCTIONS STEP 9 Make sure the reflector is at the same side as wheels. Insert the hose and regulator through the pole (6) and place the transom assembly (4) on the pole (6). Insert M8 x 85 bolt through the holes of transom assembly (4) and pole (6) and secure them with M8 cap nut. Finally tighten other 3pcs M8 cap nuts. Note: It is recommended that two people perform this step with extra caution.
ASSEMBLY INSTRUCTIONS STEP 11 Insert cylinder fixing hook (10) into holes on base assembly (8). Place the gas cylinder (not included) into the base assembly (8) and fix it with cylinder fixing hook (10). Attach the regulator to the cylinder and turn clockwise to securely tighten the valve. Close and latch the door. Note: Make sure to check for leaks after attaching the cylinder. (For instructions, refer to the “check for leaks" section of this manual.
888.779.
SAFETY CHECK WARNING: ONLY AN AUTHORIZED GAS TECHNICIAN SHOULD INSTALL THIS PRODUCT. battery compartment cover 4pcs M4 x 10 bolts. inlet pipe fitting and metal hose fitting. Battery compartment cover e. If no bubbles appear, the connection is safe. f. If bubbles appear, there is a leak. Shut off the LP gas cylinder valve, loosen and then re-tighten this connection. M4 x 10 bolts 4pcs Inlet pipe fitting line. Do not attempt to use the heater. i.
1) Turn LP Cylinder gas valve to fully open position and press “ ” button on the control panel. If the sparks stop and burner does not stay lit, press the button “ ” again to ignite after 10 seconds. ” or “ ” to desired 2) When the burner is lit, press “ heat output between High and Low. 3) To shut off heater, press “ ”again, then turn LP cylinder gas valve to closed position. If you want to relight the heater, wait 5 minutes, and then repeat the Steps 1 to 2.
15 press the control knob to the “ press 18 ”
LOCATING HEADER FOR USE CAUTION: WHEN CERTAIN MATERIALS OR ITEMS ARE LEFT, ABOVE, BESIDE OR UNDER THIS HEATER WHILE IN USE, THEY WILL BE SUBJECT TO RADIANT HEAT AND COULD BE SERIOUSLY DAMAGED. This heater is primarily used for the heating of outdoor patios, decks, spas, pools and open working areas. Always make sure that adequate fresh air ventilation is provided. Follow the spacing tolerances shown in the following figure right at all times. This heater must be placed on level, firm ground.
MAINTENANCE/STORAGE CLEANING AND MAINTENANCE : To enjoy years of outstanding performance from your heater make sure you perform the following maintenance activities on a regular basis: Keep exterior surfaces clean. Use warm soapy water for cleaning. Never use flammable of corrosive cleaning agents. WARNING: FOR YOUR SAFETY ; DO NOT touch or move heater for at least 45 minutes after use. Allow all burner elements to cool before touching.
MAINTENANCE/STORAGE Spiders and insects can nest in burner or orifices. This dangerous condition can damage heater and render it unsafe for use. Clean burner holes by using a heavy-duty pipe cleaner. Compressed air may help clear away smaller particles. Carbon deposits may create a fire hazard. Clean dome with warm soapy water if any carbon deposits develop. STORAGE: Between uses: Turn LP cylinder to "OFF" position.
22
FIVE-YEAR LIMITED WARRANTY The appliance has been manufactured under the highest standards of quality and workmanship. We warrant to the original consumer purchaser that all aspects of this product will be free of defects in material and workmanship for five (5) year from the date of purchase. A replacement for any defective part will be supplied free of charge for installation by the consumer. Defects or damage caused by the use of other than genuine parts are not covered by this warranty.
LAVA 2G LAVA LITE LAVA LITE KD OPUS EMBER WALL-E LAVA LITE MINI SORRENTO PUB TABLE ALTO QUATTRO DIABLO
ITE LIM D 5 Y W YEAR AR NT RA
