Users Manual Part 1

ManualsBrandsLAUREL PRECISION MACHINES ManualsElectronicsNote Sorter

NoteSorter

K4/K8



UserManual

Summary of content (78 pages)

PAGE 1
8 /K K4 / K8 K 4 K4/K8 K 4 8 /K K 4/ K8 K 4 8 /K 8 /K Note Sorter K4/K8 User Manual K 4 / K8 K 4
PAGE 2
Introduction Thank you very much for purchasing the "LAUREL K4/K8 note sorter". This User Manual describes safety instructions, operations, functions, specifications etc. Please read carefully and understand this manual before operating the machine. Keep this User Manual handy for ready reference. Note 1. It is strictly prohibited to use part or this entire manual to other publication without permission of publisher. 2.
PAGE 3
FCC Note This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
PAGE 4
Request from us If you don't use the machine for long, be sure to turn off the power switch. *About the installation of the machine: Avoid high temperature, high humidity, dust, vibration, and direct sunlight. 。。 In case the environment of operation exceeds room temperature (5 C to 34 C) and humidity (35% to 80%), the performance of the machine will deteriorate remarkably. Please use an air-conditioner, a humidifier, etc. in case of above conditions.
PAGE 5
Contents Introduction ............................................................................................. ii Note ..................................................................................................................................ii FCC Caution ...................................................................................................................ii FCC Note ...................................................................................................................
PAGE 6
Chapter 2 DESCRIPTION OF OPERATION 23 Starting-up and Closing-down of the Unit.................................. 24 Count ....................................................................................................... 26 Setting of Sorting Modes and Sorting Pattern........................ 29 Setting of Preset Number................................................................ 31 Total Function ......................................................................................
PAGE 7
Chapter 4 INSTALLATION, SPECIFICATIONS AND OTHERS 81 Installation ............................................................................................. 82 Condition of installation ...........................................................................................82 Installation and Transfer .........................................................................................82 Speciﬁcations ......................................................................................
PAGE 8
Before Operation This manual is used to follow symbols to make you cautious in order to use the machine safely and to prevent you from a risk of an injury or from losing your property. It describes contents of danger and/or how to prevent the danger together with marking which indicates contents of the danger near the symbols. Please read through this manual to understand the meanings of symbols and markings before use.
PAGE 9
Safety Caution WARNING PULL OUT PLUG PULL OUT PLUG ELECTRIC SHOCK If smoking, abnormal smell, noise is detected from the machine, stop the operation and pull out the plugs from outlet. Then contact A regional distributor of LAUREL. Without respect to this caution, there is risk of failure, an electric shock or a ﬁre. If a liquid is spilled over the machine or metal, burnable material are dropped inside of the machine, do not use the machine.
PAGE 10
CAUTION RISK OF INJURY DISMOUNT PLUG Do not lean over, sit, step on or place heavy material on the machine. Otherwise, there is a risk of injure due to fall down the machine. When removing the plug, be sure to hold the plug itself. If the plug is removed by holding the cable, it may cause physical failure, an electric shock or a ﬁre. Be sure to connect the earth wire to the proper grounding. Otherwise, there is a risk of electric shock.
PAGE 11
CAUTION Do not remove warning mark that describes caution for safety. Do not use the power cable which is not for the machine.There is a risk of failure, an electric shock or a ﬁre. About instantaneous voltage drop This machine may have a problem due to instantaneous voltage drop by thunderbolt etc. We recommend employing UPS etc for countermeasure. About Maintenance Service This machine requires proper maintenance service.
PAGE 12
Description of This Manual STEP-3 It describes operation procedure. K4/K8 STEP-3 Chapter 2 DESCRIPTION OF OPERATION Align the notes and put the notes onto the Hopper. ▷ The count starts automatically. ▷ If the count does not start automatically, press START/STOP ▷ Supplemental remarks about operation. Switch to start count. ▷ It is possible to put additional notes to the Hopper. ▷ When the count starts, MainDisplay indicates count result in value or quantity.
PAGE 13
Chapter 1 OVERALL DESCRIPTIONS 1
PAGE 14
Chapter 1 OVERALL DESCRIPTIONS K4/K8 Description of Each Part Overall Unit Only for K4 2. Status LED 1. Pocket LED 3. Sub-Display 4. Pocket 1 15. Reject Pocket 5. Pocket 2 16. Reject Pocket LED 6. Pocket 3 17. Note Press 7. Pocket 4 18. Note Guide 12. Operation Panel 13. START/STOP SW 14. Note Press SW 2 Description of Each Part 19. Main SW 20. Hopper 21.
PAGE 15
K4/K8 Chapter 1 OVERALL DESCRIPTIONS Only for K8 2. Status LED 1. Pocket LED 3. Sub-Display 8. Pocket 5 9. Pocket 6 15. Reject Pocket 10. Pocket 7 11. Pocket 8 16. Reject Pocket LED 17. Note Press 4. Pocket 1 5. Pocket 2 18. Note Guide 6. Pocket 3 19. Main SW 7. Pocket 4 12. Operation Panel 13. START/STOP SW 20. Hopper 21. Dust Tray 1 14.
PAGE 16
Chapter 1 OVERALL DESCRIPTIONS K4/K8 1. Pocket LED ........................... indicates status of pocket by lighting or blinking. Please refer to Indication of Pocket Status（P.6）. 2. Status LED ............................ indicates a category of note at the Pocket. Please refer to Indication of Pocket Status （P.6）. 3. Sub-Display ........................... indicates quantity of notes at the Pocket. 4. Pocket 1................................. stacks the notes to be sorted out. (Max. 200 pcs.) 5.
PAGE 17
K4/K8 Chapter 1 OVERALL DESCRIPTIONS Operation Panel 1. Main-Display 2. FUNCTION FUNCTION 3. FITNESS SETTING FITNESS SETTINGS ATM 4. CF SETTING CF SETTINGS SORT 7. FITNESS FITNESS 8. ATM 9. SORT FACE ORIENT 5. 10. FACE/ORIENT DISPLAY 6. 11. ISSUE ISSUE 12. F1 13. F2 14. F3 15. F4 16. F5 1. Main-Display.......................... - indicates count results in Value, Quantity or Mode settings. - indicates the error code in case of an error. 2. FUNCTION .............................
PAGE 18
Chapter 1 OVERALL DESCRIPTIONS Indication of Pocket Status Only for K4 1. Status LED 2. Pocket LED 3. Pocket Count Display Only for K8 1. Status LED 2. Pocket LED 3.
PAGE 19
K4/K8 Chapter 1 OVERALL DESCRIPTIONS 1. Status LED ............................ LED indicates note category by color of light. LED Blue Green Orange Red FITNESS Fit ─ Unﬁt CF ATM ATM Fit Unﬁt CF SORT（Denom.） Single Mixed ─ CF FACE Fit ─ ─ CF ORIENT Fit ─ ─ CF ISSUE（Old/New） New Old 2 generation old CF Sorting Mode 2. Pocket LED ........................... guides operators to remove notes. When it is ready for removing them, LED lights on after blinking 2 seconds. 3.
PAGE 20
Chapter 1 OVERALL DESCRIPTIONS K4/K8 Description of Display Stand-by Display ♦ Stand-by Display indicates present sorting mode, preset number and target currency. ♦ While showing Stand-by Display, the count starts by pressing START/ STOP SW. Present mode Present sorting pattern Status Information Press F1 key System Info to indicate Total count results. It indicates total number of notes counted by validator. Back to Stand-by Display.
PAGE 21
K4/K8 Chapter 1 OVERALL DESCRIPTIONS Count Display ♦ When counting starts, the display turns from Stand-by Display to Count Display and count result will be shown. Present mode Acceptable operation or pocket status. Pocket status Blinking: The Pocket is full. Lighting: A note remains. Count results in value and pieces. Press F1 key Info to indicate each pocket count results.
PAGE 22
Chapter 1 OVERALL DESCRIPTIONS K4/K8 Guidance for Cleaning ♦ When the cleaning is required, the display indicates Cleaning Guidance on the display after turning on the power. If the Cleaning Guidance is indicated, clean the dust trays. Refer to Cleaning （P.49）for further details about cleaning.
PAGE 23
K4/K8 Chapter 1 OVERALL DESCRIPTIONS Error Display ♦ If a note jam occurs, the display switches Error Display and the display indicates error code and error location by graphic guidance. ♦ Refer to How to clear an error（P.56）and clear the error. Only for K4 Error code. Detailed Error code. Highlighting where notes remain. Blinking where an error occurs. After removing all remaining notes, press F5 key below the reset icon to reset the error. Only for K8 Error code. Detailed Error code.
PAGE 24
Chapter 1 OVERALL DESCRIPTIONS K4/K8 Description of Sorting Mode and Sorting Pattern About mode of sorting ♦ Following modes are available. 1）FITNESS Mode ....................... Sorting out ﬁt and unﬁt notes. 2）ATM Mode................................ Sorting out ATM-ﬁt notes. 3）SORT Mode ............................. Sorting out denominations. 4）FACE/ORIENTATION Mode........ Sorting out facing or orientation of notes. 5）ISSUE Mode ............................
PAGE 25
K4/K8 Chapter 1 OVERALL DESCRIPTIONS Only for K8 ♦ Press FITNESS key to activate FITNESS Mode and display indicates sorting pattern for each pocket. FUNCTION FITNESS FITNESS SETTINGS ATM CF SETTINGS SORT FACE ORIENT DISPLAY ISSUE ♦ Press F1 key or F4 key to select the display screen. Press F2 key or F3 key to set sorting pattern. The contents of sorting patterns are following.
PAGE 26
Chapter 1 OVERALL DESCRIPTIONS K4/K8 ATM Mode Only for K4 ♦ Press ATM key to activate ATM Mode and display indicates sorting pattern for each pocket. FUNCTION FITNESS FITNESS SETTINGS ATM CF SETTINGS SORT FACE ORIENT DISPLAY ISSUE ♦ Press F1 key to F3 key to set sorting pattern. The contents of sorting patterns are following.
PAGE 27
K4/K8 Chapter 1 OVERALL DESCRIPTIONS Only for K8 ♦ Press ATM key to activate ATM Mode and display indicates sorting pattern for each pocket. FUNCTION FITNESS FITNESS SETTINGS ATM CF SETTINGS SORT FACE ORIENT DISPLAY ISSUE ♦ Press F1 key or F4 key to select the display screen. Press F2 key or F3 key to set sorting pattern. The contents of sorting patterns are following.
PAGE 28
Chapter 1 OVERALL DESCRIPTIONS K4/K8 SORT Mode Only for K4 ♦ Press SORT key to activate SORT Mode and display indicates sorting pattern for each pocket. FUNCTION FITNESS FITNESS SETTINGS ATM CF SETTINGS SORT FACE ORIENT DISPLAY ISSUE ♦ Press F1 key to F4 key to set sorting pattern. The contents of sorting patterns are following. ♦ Sorting Pattern Pocket 1 2 3 4 Pocket 1 1 1 1 1 Pocket 2 1 1 2 2 Pocket 3 1 1 3 3 Pocket 4 1 CF Other CF 1=First denomination to be counted.
PAGE 29
K4/K8 Chapter 1 OVERALL DESCRIPTIONS Only for K8 ♦ Press SORT key to activate SORT Mode and display indicates sorting pattern for each pocket. FUNCTION FITNESS FITNESS SETTINGS ATM CF SETTINGS SORT FACE ORIENT DISPLAY ISSUE ♦ Press F1 key or F4 key to select the display screen. Press F2 key or F3 key to set sorting pattern. The contents of sorting patterns are following.
PAGE 30
Chapter 1 OVERALL DESCRIPTIONS K4/K8 FACE/ORIENTATION Modes Only for K4 ♦ Press FACE/ORIENT key to activate FACE/ORIENTATION Mode and display indicates sorting pattern for each pocket. FUNCTION FITNESS FITNESS SETTINGS ATM CF SETTINGS SORT FACE ORIENT DISPLAY ISSUE ♦ Press F1 key or F2 key to set sorting pattern. The contents of sorting patterns are following.
PAGE 31
K4/K8 Chapter 1 OVERALL DESCRIPTIONS Only for K8 ♦ Press FACE/ORIENT key to activate FACE/ORIENTATION Mode and display indicates sorting pattern for each pocket. FUNCTION FITNESS FITNESS SETTINGS ATM CF SETTINGS SORT FACE ORIENT DISPLAY ISSUE ♦ Press F2 key or F3 key to set sorting pattern. The contents of sorting patterns are following.
PAGE 32
Chapter 1 OVERALL DESCRIPTIONS K4/K8 ISSUE Mode Only for K4 ♦ Press ISSUE key to activate ISSUE Mode and display indicates sorting pattern for each pocket. FUNCTION FITNESS FITNESS SETTINGS ATM CF SETTINGS SORT FACE ORIENT DISPLAY ISSUE ♦ Press F1 key or F2 key to set sorting pattern. The contents of sorting patterns are following.
PAGE 33
K4/K8 Chapter 1 OVERALL DESCRIPTIONS Only for K8 ♦ Press ISSUE key to activate ISSUE Mode and display indicates sorting pattern for each pocket. FUNCTION FITNESS FITNESS SETTINGS ATM CF SETTINGS SORT FACE ORIENT DISPLAY ISSUE ♦ Press F2 key or F3 key to set sorting pattern. The contents of sorting patterns are following.
PAGE 34
22
PAGE 35
Chapter 2 DESCRIPTION OF OPERATION 23
PAGE 36
Chapter 2 DESCRIPTION OF OPERATION K4/K8 Starting-up and Closing-down of the Unit ♦ The unit starts up by turning on Main SW. Turn OFF Main SW when closing the Unit. ♦ The self-check function activates when the power is on. When no error is found in self-check, the stand-by display is indicated and gets ready for counting. Only for K4 Stand-by Display ON Ex. Fitness OFF Only for K8 Stand-by Display ON 24 Starting-up and Closing-down of the Unit OFF Ex.
PAGE 37
K4/K8 Chapter 2 DESCRIPTION OF OPERATION ♦ If an error is found in self-check, Error Display is indicated. Clear the error according to the error showing on the display. Refer to Setting of Sorting Modes and Sorting Pattern（P.29）. Only for K4 ♦ Only for K8 If the dust tray cleaning is required, Maintenance Info Display is indicated after turning on the power. Clean the dust trays according the information showing on the display. Without cleaning dust trays, the display does not show Stand-by Display.
PAGE 38
Chapter 2 DESCRIPTION OF OPERATION K4/K8 Count STEP-1 If necessary change Sorting Mode or Sorting Pattern. Refer to Setting of Sorting Modes and Sorting Pattern（P.29）for further details.
PAGE 39
K4/K8 STEP-3 Chapter 2 DESCRIPTION OF OPERATION Adjust Note Guide to size of note. ▷ Move Note Guide by holding rib part. rib part STEP-4 Align the notes and put the notes onto the Hopper. ▷ The count starts automatically. ▷ If the count does not start automatically, press START/STOP Switch to start count. ▷ It is possible to put additional notes to the Hopper. ▷ When the count starts, MainDisplay indicates count result in value or quantity.
PAGE 40
Chapter 2 DESCRIPTION OF OPERATION STEP-5 When completing the transaction after the count, be sure no note on the Hopper and press START/ STOP switch. ▷ When START/STOP switch is pressed without note at the Hopper, the count result on the display is cleared.
PAGE 41
K4/K8 Chapter 2 DESCRIPTION OF OPERATION Setting of Sorting Modes and Sorting Pattern STEP-1 Press sorting key to set a Sorting Mode. Only for K4 Ex. Fitness Only for K8 Ex. Fitness FUNCTION FITNESS FUNCTION FITNESS FITNESS SETTINGS ATM FITNESS SETTINGS ATM SORT CF SETTINGS SORT CF SETTINGS FACE ORIENT DISPLAY FACE ORIENT DISPLAY ISSUE ISSUE STEP-2 Ex. Fitness Only for K4 Press F1 key to F4 key to select FUNCTION sorting pattern.
PAGE 42
Chapter 2 DESCRIPTION OF OPERATION STEP-3 K4/K8 Press F5 key to return to Stand-by Display. Only for K8 Ex. Fitness Only for K4 Ex.
PAGE 43
K4/K8 Chapter 2 DESCRIPTION OF OPERATION Setting of Preset Number STEP-1 If the display indicates sorting pattern, press F5 key Exit to return to Stand-by Display. Only for K8 Ex. Fitness Only for K4 Ex. Fitness FUNCTION FITNESS FUNCTION FITNESS FITNESS SETTINGS ATM FITNESS SETTINGS ATM CF SETTINGS SORT CF SETTINGS SORT FACE ORIENT DISPLAY FACE ORIENT DISPLAY ISSUE STEP-2 ISSUE Press F3 key Preset . ▷ Preset Setting display is indicated. Only for K4 Ex. Fitness Only for K8 Ex.
PAGE 44
Chapter 2 DESCRIPTION OF OPERATION STEP-4 K4/K8 Press F5 key Exit to return to Stand-by Display after saving the preset number.
PAGE 45
K4/K8 Chapter 2 DESCRIPTION OF OPERATION Total Function ♦ When option printer is connected, a result of count can be printed out. 1）Grand Total ...................... It indicates Ground Total. 2）Operator Record*1) ......... It indicates count Record per operator. 3）Fitness Record ............... It indicates percentage of ﬁt and unﬁt result. 4）History ............................... It indicates Record of operations.
PAGE 46
Chapter 2 DESCRIPTION OF OPERATION K4/K8 When printing out (Option) 1. Press F3 key Print . FUNCTION FITNESS FITNESS SETTINGS ATM CF SETTINGS SORT FACE ORIENT DISPLAY ISSUE ▷ The display indicates printing screen. It returns back to previous screen after completing print out. When clearing data 1. Press F1 key Clear . FUNCTION ▷ The display indicates data clear screen. FITNESS FITNESS SETTINGS ATM CF SETTINGS SORT FACE ORIENT DISPLAY ISSUE 2. Press F1 key ENT .
PAGE 47
K4/K8 Chapter 2 DESCRIPTION OF OPERATION 3. Input operator number by F3 key − or F4 key + . ♦ Press F2 key to move the cursor to desired digit. 4. Press F1 key ENT . FUNCTION FITNESS FITNESS SETTINGS ATM CF SETTINGS SORT FACE ORIENT DISPLAY ISSUE ▷ The display indicates total for 4. selected operator. 3. When printing out (Option) 1. Press F3 key Print . FUNCTION FITNESS FITNESS SETTINGS ATM CF SETTINGS SORT FACE ORIENT DISPLAY ISSUE ▷ The display indicates printing screen.
PAGE 48
Chapter 2 DESCRIPTION OF OPERATION K4/K8 When clearing data 1. Press F1 key Clear . FUNCTION ▷ The display indicates data clear screen. FITNESS FITNESS SETTINGS ATM CF SETTINGS SORT FACE ORIENT DISPLAY ISSUE 2. Press F1 key ENT . ▷ The display returns back to previous screen after clearing data. FUNCTION FITNESS FITNESS SETTINGS ATM CF SETTINGS SORT FACE ORIENT DISPLAY ISSUE History 1. Move the cursor to History by △ Key or ▽ key. 2. Press F1 key ENT .
PAGE 49
K4/K8 Chapter 2 DESCRIPTION OF OPERATION When printing out (Option) 1. Press F3 key Print . FUNCTION FITNESS FITNESS SETTINGS ATM CF SETTINGS SORT FACE ORIENT DISPLAY ISSUE ▷ The display indicates printing screen. It returns back to previous screen after completing print out.
PAGE 50
Chapter 2 DESCRIPTION OF OPERATION K4/K8 Setting of Fitness Level STEP-1 Press FITNESS SETTING key while the display is showing Stand-by Display. ▷ The display indicates Fitness Setting Display. ▷ If Admin Mode is activated, the password is required. Only for K4 Ex. Fitness FUNCTION Only for K8 Ex. Fitness FITNESS FUNCTION FITNESS SETTINGS ATM FITNESS SETTINGS FITNESS ATM CF SETTINGS SORT CF SETTINGS SORT FACE ORIENT DISPLAY FACE ORIENT DISPLAY ISSUE ISSUE How to input the password.
PAGE 51
K4/K8 Chapter 2 DESCRIPTION OF OPERATION 3. Move the cursor to your desired Fitness Level by F1 key or F2 key. FUNCTION FITNESS FITNESS SETTINGS ATM CF SETTINGS SORT FACE ORIENT DISPLAY ISSUE 3. ▷ If L, M, H or (EU) of ALL is selected, Fitness Level of all denominations will be set all together. 4. Skip STEP-3 and go to STEP-4. FUNCTION FITNESS FITNESS SETTINGS ATM CF SETTINGS SORT FACE ORIENT DISPLAY ISSUE 3. STEP-3 Detailed Fitness Level Setting 1.
PAGE 52
Chapter 2 DESCRIPTION OF OPERATION STEP-4 K4/K8 Press F5 key Exit to return the display to Stand-by Display. ▷ Fitness Level is memorized.
PAGE 53
K4/K8 Chapter 2 DESCRIPTION OF OPERATION Setting of CF Level ♦ STEP-1 CF Level means the level of security feature detection. Press CF SETTING key while the display is showing Stand-by Display. ▷ CF Setting Display is indicated. ▷ If Admin Mode is activated, the password is required. Only for K8 Ex. Fitness Only for K4 Ex.
PAGE 54
Chapter 2 DESCRIPTION OF OPERATION K4/K8 3. Move the cursor to desired CF Level by F1 key or F2 key. 4. Skip STEP-3 and go to STEP-4. FUNCTION FITNESS FITNESS SETTINGS ATM CF SETTINGS SORT FACE ORIENT DISPLAY ISSUE 3. STEP-3 Detailed CF Level Setting 1. Press CF SETTING key again while the display is showing CF Setting Display. Detailed CF Setting 1. FUNCTION FITNESS FITNESS SETTINGS ATM CF SETTINGS SORT Display is indicated. FACE ORIENT DISPLAY ISSUE 2.
PAGE 55
K4/K8 Chapter 2 DESCRIPTION OF OPERATION Function Setting 1）Currency ........ Currency Selection. 2）Language ...... Language Selection. 3）Contrast......... Contrast Setting of Main-Display. 4）Back Light..... Time Setting of Back Light saving mode. 5）Buzzer ............. Volume Setting of Buzzer. 6）Date ................ Date Setting of internal clock. 7）Time ................ Time Setting of internal clock. 8）Printer ............. Printer Setting(Printer is option.) 9）Admin..............
PAGE 56
Chapter 2 DESCRIPTION OF OPERATION K4/K8 Language 1. M o v e t h e c u r s o r t o s e l e c t Language by △ Key or ▽ key. 2. M o v e t h e c u r s o r t o d e s i r e d Language by F1 Key or F2 key. FUNCTION FITNESS FITNESS SETTINGS ATM CF SETTINGS SORT 1. FACE ORIENT DISPLAY ISSUE 2. Contrast 1. Move the cursor to Contrast by △ Key or ▽ key. 2. Adjust the contrast by F3 key − or F4 key + . FUNCTION FITNESS FITNESS SETTINGS ATM CF SETTINGS SORT 1. FACE ORIENT DISPLAY ISSUE 2.
PAGE 57
K4/K8 Chapter 2 DESCRIPTION OF OPERATION Date 1. Move the cursor to Date by △ Key or ▽ key. FUNCTION FITNESS FITNESS SETTINGS ATM CF SETTINGS SORT 1. FACE ORIENT DISPLAY ISSUE 2. Move the cursor to year, month or day by F1 key or F2 key. FUNCTION 3. Change the value by F3 key − or F4 key + . FITNESS FITNESS SETTINGS ATM CF SETTINGS SORT FACE ORIENT DISPLAY ISSUE 2. 3. Time 1. Move the cursor to Time by △ Key or ▽ key. FUNCTION FITNESS FITNESS SETTINGS ATM CF SETTINGS SORT 1.
PAGE 58
Chapter 2 DESCRIPTION OF OPERATION K4/K8 Printer ♦ Regarding printer connection, please contact your regional distributors. ♦ The following describes the setting after connecting a printer. 1. Move the cursor to Printer by △ Key or ▽ key. 2. Press F3 key ENT . FUNCTION FITNESS FITNESS SETTINGS ATM CF SETTINGS SORT 1. FACE ORIENT DISPLAY ISSUE 2. 3. Move the cursor to Printer by △ Key or ▽ key. FUNCTION 4. Set it to ON by F1 key or F2 key.
PAGE 59
K4/K8 Chapter 2 DESCRIPTION OF OPERATION Admin 1. Move the cursor to Admin by △ Key or ▽ key. 2. Press F3 key ENT . FUNCTION FITNESS FITNESS SETTINGS ATM CF SETTINGS SORT 1. FACE ORIENT DISPLAY ▷ Password Input Display is ISSUE indicated. 2. 3. Select a number by F1 key or F2 key and input it by F3 key ENT one by one. ▷ If the password is identical, the FUNCTION FITNESS FITNESS SETTINGS ATM CF SETTINGS SORT display indicates Administrator FACE ORIENT DISPLAY Setting Display.
PAGE 60
Chapter 2 DESCRIPTION OF OPERATION K4/K8 In order to change password 4-1. Move the cursor to Password Setting by △ Key or ▽ key. 4-2. Press F3 key ENT . FUNCTION FITNESS FITNESS SETTINGS ATM CF SETTINGS SORT 4-1. FACE ORIENT DISPLAY ISSUE 4-2. 4-3. Input the current password and new password. FUNCTION ▷ FUNCTION display is indicated after changing the password. FITNESS FITNESS SETTINGS ATM CF SETTINGS SORT FACE ORIENT DISPLAY ISSUE 4-3.
PAGE 61
K4/K8 Chapter 2 DESCRIPTION OF OPERATION Cleaning Periodical Cleaning and Position ♦ Clean the Dust Trays at least once in a day. Dust Tray 1 and Dust Tray 2 ♦ Clean the Transportation Path 1 and the Validator periodically. Cleaning the Dust Tray 1 STEP-1 Hold the handle of Dust Tray 1 and pull it out. Remove the dust in the Dust Tray 1. STEP-2 Set the Dust Tray 1 back to the unit.
PAGE 62
Chapter 2 DESCRIPTION OF OPERATION K4/K8 Cleaning the Dust Tray 2 STEP-1 Open the Front Door by the handle. Only for K4 STEP-2 Only for K8 Pull out Dust Tray 2 by holding green parts. Remove the dust in the Dust Tray 2. STEP-3 Set the Dust Tray 2 back to the unit.
PAGE 63
K4/K8 STEP-4 Chapter 2 DESCRIPTION OF OPERATION Close the Front Door.
PAGE 64
Chapter 2 DESCRIPTION OF OPERATION K4/K8 Cleaning Sensors STEP-1 Open the Front Door by the handle. Only for K4 STEP-2 Only for K8 Open the Transportation Path 1 and remove the dust. 1. Unlock the Transportation Path 1 by lever 1 and open it. Lever 1 2. Clean the transportation path by cotton swab or brush. To remove the dust.
PAGE 65
K4/K8 Chapter 2 DESCRIPTION OF OPERATION 3. Close the Transportation Path 1 gently by holding lever 1. ♦ Be sure to lock the Transportation Path 1 by locking lever 1. STEP-3 Open the Validator and clean the sensors. 1. Unlock the clamp of Validator. Lever 3 2. Open Validator with holding lever 3. 2. Clamp 1. 3. Clean the Validator by cotton swab or brush. To clean the sensors. To clean the sensors. 4. Open the Transportation Path 2 by holding lever 2 and remove the dust by cotton swab or brush.
PAGE 66
Chapter 2 DESCRIPTION OF OPERATION K4/K8 5. Close the Transportation Path 2 gently. 6. Close the Validator by holding lever 3. 7. Lock the Validator by clamp. Lever 3 Clamp 6. 7. STEP-4 Close the Front Door.
PAGE 67
Chapter 3 IF AN ERROR OCCUR 55
PAGE 68
Chapter 3 IF AN ERROR OCCURS K4/K8 How to clear an error This chapter describes action to be taken when an error occurs. Error Display ♦ If an error occurs such as note jam, the main-display switches to Error Display which shows error code and location of the error by guidance. ♦ In order to clear the error, check the error code and location of error and take remedial action correspond to Error and Remedial Measure page 49. Only for K4 Error Code 61 Error Detail Code 30-12.
PAGE 69
K4/K8 Chapter 3 IF AN ERROR OCCURS Error and Remedial Measure Error Code Content of Error Remedial Measure 1. Remove remaining notes according to the guidance on the display. 2. Press Reset key. Error 10 to 32 Mechanical Error 3. If the notes are discharged to the pockets after the reset actions, remove the notes from the pockets. Refer to How to remove jam notes（P.58）. Error 40 Validator Error 1. Remove remaining note according to the guidance on the display. Refer to How to remove jam notes（P.
PAGE 70
Chapter 3 IF AN ERROR OCCURS K4/K8 How to remove jam notes Description of Guidance Only for K4 Pocket Transportation Unit 1（P.72） Upper Transportation Unit（P.67） Reject Pocket（P.59） Pocket（P.60） Hopper（P.59） Main Transportation Unit（P.63） Feed Unit（P.61） Only for K8 Pocket Transportation Unit 1（P.72） Upper Transportation Unit（P.67） Pocket Transportation Unit 2 （Only for K8）（P.76） Reject Pocket（P.59） Pocket（P.60） Hopper（P.59） Main Transportation Unit（P.
PAGE 71
K4/K8 Chapter 3 IF AN ERROR OCCURS Hopper STEP-1 Remove all the notes from the Hopper. STEP-2 Press F5 key Reset . ▷ The reset action gets started. FUNCTION ▷ Stand-by Display is shown after completing the reset action normally. FITNESS FITNESS SETTINGS ATM CF SETTINGS SORT FACE ORIENT DISPLAY ISSUE Reject Pocket STEP-1 Remove all the notes from the Reject Pocket.
PAGE 72
Chapter 3 IF AN ERROR OCCURS STEP-2 K4/K8 Press F5 key Reset . ▷ The reset action gets started. ▷ Stand-by Display is shown after completing the reset action normally. FUNCTION FITNESS FITNESS SETTINGS ATM CF SETTINGS SORT FACE ORIENT DISPLAY ISSUE Pocket STEP-1 Remove all the notes from the Pockets. STEP-2 Press F5 key Reset . ▷ The reset action gets started. FUNCTION ▷ Stand-by Display is shown after completing the reset action normally.
PAGE 73
K4/K8 Chapter 3 IF AN ERROR OCCURS Feed Unit STEP-1 Open the Front Door by the handle. Only for K4 STEP-2 Only for K8 Remove remained note by opening the Transportation Path 1. H o l d L e v e r 1 t o u n l o c k t h e Transportation Path 1 to open. Lever 1 2. Remove remained note. If the note are blocked, turn the knob A. Then remove it. To remove a note.
PAGE 74
Chapter 3 IF AN ERROR OCCURS K4/K8 3. By holding the Lever 1, close the Transportation Path 1 gently. ♦ Release the Lever 1 and make sure that the Transportation Path 1 gets locked. STEP-3 Close the Front Door. ▷ The reset action gets started. ▷ Stand-by Display is shown after completing the reset action normally. Only for K4 Only for K8 ▷ If the reset action does not gets started, press F5 key Reset to activate it.
PAGE 75
K4/K8 Chapter 3 IF AN ERROR OCCURS Main Transportation Unit STEP-1 Open the Front Door by the handle. Only for K4 STEP-2 Only for K8 Open the Upper Door and be sure to lock the door kept open. Only for K4 STEP-3 Only for K8 Open the Transportation Path 4, 2. 1. Unlock Transportation Path 4 by 1. pressing Lever 4 in the direction to arrow mark. 2. Open Transportation Path 4 till locking the position.
PAGE 76
Chapter 3 IF AN ERROR OCCURS STEP-4 K4/K8 Open the Validator Unit and remove remained notes. 1. Release the clamp of Validator Lever 3 Unit. 2. Open the Validator Unit by holding 2. the Lever 3. Clamp 1. 3. Remove note by rotating Knob C in the direction of the arrow mark. Knob C To remove a note. In case a note is blocked. 3-1. Open the Transportation Path 2 by the Lever 2 and remove Knob C a note blocked by rotating the Knob C. Lever 2 3-2. Close the Transportation Path 2 gently.
PAGE 77
K4/K8 STEP-5 Chapter 3 IF AN ERROR OCCURS Close the Validator Unit. 1. Close the Validator Unit by the Lever 3. Lever 3 2. Lock Validator Unit by clamp. Clamp 1. 2. STEP-6 Close the Transportation Path 4. 1. 2. 1. Keep up the Transportation Path 4 by the Lever 4 and unlock by pressing Lever 5. 2. Close the Transportation Path 4 gently. Lever 4 1. Lever 5 STEP-7 Close the Front Door.
PAGE 78
Chapter 3 IF AN ERROR OCCURS STEP-8 K4/K8 Close the Upper Door. 1. Keep up the Upper Door by the handle to unlock by pressing Lever 6. 2. Close the Upper Door gently. ▷ The reset action gets started. ▷ Stand-by Display is shown after completing the reset action normally. Lever 6 Lever 6 Handle Handle 1. 1. 1. 1. 2. 2. Only for K4 Only for K4 ▷ If the reset does not get started, press F5 key to activate the reset.