Installation Guide
Multi-Piece Sectional Product
Installation Instructions
aligned to the mounting holes. Utilizing the six (6) #10 x 2” Stainless
Steel screws, place a Phillips screw driver into your power drill and
securely tighten each of the six (6) screws.
THIS COMPLETES THE INSTALLATION OF THE SEAT
INSTALLATION INSTRUCTIONS FOR GRAB BARS
Recommended tools for installation:
1/4” Power Drill
1/8” drill bit when drilling through berglass
#2 Phillips Screw Driver and/or Phillips drill insert
1/2” Open end wrench or a small Crescent wrench
Tape measure
Pencil/pen
Center Punch
Silicone Caulk
1. As indicated earlier in this manual, wood reinforcements must
be solidly installed behind the tile wall surface to provide a secure
mounting surface to attach the grab bars. Grab bars must be
installed at these locations only.
2. Select the particular size and style of grab bar you want to
install. Certain grab bars have snap in place ange covers, and
others have exposed anges.
3. For grab bars with snap in place ange covers, use the handle
of a Phillips screw driver to tap back the covers on the bottom
edge of the covers. It will be convenient in the installation process
if the covers are tapped together in the center of the grab bar.
4. Determine the position you want the to install the bar. Place
the bar against the wall. Using a pencil, mark the location of each
mounting hole at both ends of the bar.
5. Using a power drill with a 1/4” diameter carbide tipped drill bit,
drill, each mounting hole.
6. Apply silicone caulking around and inside each drilled hole
before installing the grab bar.
7. Take two (2) of the #10 x 2” Stainless Steel screws. By hand,
start one mounting screw in each end of the bar into the wall.
8. Use a power drill with a Phillips drill bit to fully install these
mounting screws.
9. Take the remaining #10 x 2” screws and place them into the
remaining open holes. Use care to snug up the screws, but to not
over-torque that the screws strip out the factory installed backer
board.
10. If installing a bar with snap-on covers, move the covers
into place at each ange. Twist the covers clockwise or counter
clockwise to tighten the covers onto the anges.
THIS COMPLETES THE INSTALLATION OF THE GRAB BAR
INSTALLATION INSTRUCTIONS FOR COLLAPSIBLE WATER
RETAINERS
Important considerations before you begin: Most manufactured
units are designed with a radius where the oor transitions or
meets the wall. This is to ensure proper structural strength where
the wall meets the oor. The installation of end caps is highly
recommended on radius models for proper t and nish. The
caps will also help to keep your curtain inside the water barrier.
A properly sized curtain with heavy tape weights combined with
Materials Required:
Acrylic Latex Caulk
Wiping Cloths (Rags)
Clean Water
Cut off tip of caulk tube diagonally with opening
no larger than 1/8”.
(Figure 27)
Run a continuous bead of caulk at the seam between
the two parts.
(Figure 28)
Smooth caulk gently with a wet fingertip. (Figure 29)
Using a clean rag, wipe off excess water and caulk.
(Figure 30)
12
Seam Caulking Instructions
Figure 27
Figure 28
Figure 30
Figure 29
Tools Required:
Caulking Gun
Cup
Your seat with swing down legs is fully assembled. Remove it from the box and proceed as follows:
(This style seat has four (4) adjustable height legs)
1.- Choose the height of the seat you want. Barrier Free style showers will typically have fold up
seat installed at 17” to 19” height.
2.- After selecting the height you desire, adjust each of the four legs to that height while
maintaining the seat in a level position. Lock each of the lock nuts.
3.- Place the seat against the wall of the shower where you want the seat to be located.
Seat may be centered on the wall for a Barrier Free installation.
INSTALLATION INSTRUCTIONS FOR SHOWER SEATS
WITH SWING DOWN ADJUSTABLE LEGS
4.- With the seat placed against the mounting wall, position the two hinges to the wall.
Using a pencil, mark the three holes (3) holes in the flange onto the wall for each hinge.
Remove seat from wall.
10