Installation Guide

ManualsBrandsLaurel Foundry Modern Farmhouse ManualsBronze Outdoor Hanging LightsLois 2 -Bulb 23.5" H Outdoor Hanging Lantern

1of3

Warnings and Cautions

Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.

These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly

recommend that a licensed, professional electrician perform the installation.

Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal.

(2)B10CandelabraBaseBulbs60WMaximum,CandelabraBaseT8Vintage Bulbs are recommended, bulbs not included.

MinimumHangingHeightis28.5”,MaximumHangingHeightis125”.

30-45minutes

Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtoensureallpartsare

present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.Contactyouroriginalplaceofpurchase.

LightSource:

FixtureHangingHeight:

EstimatedAssemblyTime:

Preparation:

ToolsRequired: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses.

Package Contents

Side Rod

Hardware Contents

Crossbar

Assembly

Ceiling

Canopy

Fixture Chain

Quick Link

STEP 1 - Install Fixture Loop

A. Thread the Fixture Loop (B)

onto the nipple on the top center

of the Fixture Holder (C). Hand

tighten until snug.

Figure 1

STEP 2 - Remove Papers Inside of the Cage

A. Rotate the bolt and remove it from the bolt holder to open the door.

B. Remove papers inside of the cage.

C. Close the door and place the bolt back onto the bolt holder.

Figure 2

Door

Bolt

Bolt Holder

Paper

(Remove)

STEP 3 - Install the Crossbar Assembly to Outlet Box and Adjust

the length of the Nipple

A. Attach the Crossbar Assembly (AA) to the Outlet Box with the head

of the Green Ground Screw facing you. Secure it with Outlet Box

Screws (not included), tighten until snug

B. Adjust the hex nut and lock washer underside of the crossbar to the

middle of the nipple.

C. Remove the canopy lock ring from the canopy chain loop. Place the

Ceiling Canopy (DD) over the canopy chain loop against the ceiling

to determine the correct position of the nipple. Thread the canopy

lock ring onto the canopy chain loop. Adjust the nipple to allow the

Ceiling Canopy (DD) to rest against the ceiling when held in place

Outlet Box Screw

(not included)

Hex Nut and

Lock Washer

Outlet Box

Green Ground Screw

Canopy Chain Loop

Canopy Lock Ring

Nipple

Figure 3

Fixture Loop

Fixture

Holder

Fixture Body

Installation Guide

Summary of content (3 pages)

PAGE 1
Installation Guide Tools Required: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses. Light Source: (2) B10 Candelabra Base Bulbs 60W Maximum, Candelabra Base T8 Vintage Bulbs are recommended, bulbs not included. Fixture Hanging Height: Minimum Hanging Height is 28.5”, Maximum Hanging Height is 125”. Estimated Assembly Time: 30-45 minutes Preparation: Identify and inspect all parts before beginning installation.
PAGE 2
(Step 3 Continued) (Step 5 Continued) by the canopy lock ring. D. Remove the canopy lock ring and the Ceiling Canopy (DD). Tighten the lock washer and the hex nut against the crossbar to secure in place. Note: If the electrical wire is going to be cut shorter than provided you will need to identify the "L" line wire and the "N" neutral wire before you cut the excess wire off. One is labeled N and the other labeled L. To do this separate the "L" line wire and the "N" neutral wire as far as you need to.
PAGE 3
FINISH: INDUSTRIAL BRONZE NOTE: ALL DIMENSIONS ARE ROUNDED UP TO THE NEAREST 1/4" 5.5” Dia. 125” 23.5” 18.25” 10.5” SQ. 21.