Quick Start Guide

1. The DLC (Data Link Connector) is typically a connector
where diagnostic code readers interface with the vehicle's on-board computer.
2.
3.
4. To perform vehicle diagnosis via USB cable, connect the B-shaped terminal of the
USB cable to the HD III and other end to the USB port of the scan tool.
Locate the vehicle’s DLC:
The
DLC location varies from vehicle to vehicle. It is generally located in driver’s cab. If
no DLC is found, please refer to Automobile Repair Manual.
Switch the ignition on.
For vehicles equipped with OBD II management system, plug one end of the
diagnostic cable into the vehicle’s DLC, and the other end into the diagnostic
socket of the HD III, and then tighten the captive screws.
For vehicles not equipped with OBD II management system, it is necessary to use
the corresponding adaptor cable, and then follow one of the methods below to
make connection:
To establish the Wi-Fi communication between the HD III and scan tool, proceed the
following steps:
2. Power the scan tool on and launch the application
3. After logging successfully, tap -> “Profile” -> “Connector communication
manager” -> select “Use Wi-Fi communication”, a pull-down option list appears:
Work as Wi-Fi hotspot: Once enabled, the and scan tool forms a LAN
network to make communication. In this case, the scan tool can not surf the
Internet.
Work as network adaptor: Once enabled, a Wi-Fi connection dialog box appears.
Input the Wi-Fi network name and access password until it is properly connected.
In this case, the scan tool can surf the Internet and communicate with .
1. Follow the steps mentioned in Section 1 to make connection.
.
HD III
HD III
1. Manufacturers shall ensure that radio equipment shall be so constructed that it can be
operated in at least one Member State without infringing applicable requirements on the use
of radio spectrum.
2. In cases of restrictions on putting into service or of requirements for authorisation of use,
information available on the packaging shall allow the identification of the Member States or
the geographical area within a Member State where restrictions on putting service or
requirements for authorisation of use exist. Such information shall be completed in the
restrictions accompanying the radio equipment. The Commission may adopt implementing
acts specifying how to present that information. Those implementing acts shall be adopted in
accordance with the advisory procedure referred to in Article 45(2).
LAUNCH
1
2
Vehicle Connection
Wi-Fi Communication Setup
4
HD III Diagnostic cable
Cigarette lighter
Battery clamps cable
Adaptor cable To vehicle's DLC
To Cigarette lighter receptacle
To vehicle battery
Power adaptor
To AC outlet
A
B
C
3
Activate HD III & Download Software
If you had a diagnostic tool of 12V passenger car configuration and intend to
experience the diagnosis of commercial vehicles, follow the steps described
below to activate the HD III:
Note: Please make sure that the diagnostic tool is properly connected to the Internet before
proceeding this step.
1. Launch the application, then tap -> “Profile”/ “My Data” -> “Activate
Connector”.
2. Input the Product S/N and Activation Code, which can be obtained from the
included Password Envelope, then tap “Activate” to activate the .
3. Tap “Update” to enter update center, tap “Update” to download and install it.
HD III
If you had a diagnostic tool of 12V passenger car configuration and intend to
experience the diagnosis of commercial vehicles, follow the steps described
below to activate the HD III:
Note: Please make sure that the diagnostic tool is properly connected to the Internet before
proceeding this step.
1. Launch the application, then tap -> “Profile”/ “My Data” -> “Activate
Connector”.
2. Input the Product S/N and Activation Code, which can be obtained from the
included Password Envelope, then tap “Activate” to activate the .
3. Tap “Update” to enter update center, tap “Update” to download and install it.
HD III
Tap “Diagnostic”
Select vehicle model
Select test system
Select test function
Tap “Login”
Is HD III
activated?
No
Tap “Update” to
download software
Yes
Follow instructions
to activate it
Start Diagnostics
Note: Pictures illustrated herein are
for reference purpose only and this
Quick Start Guide is subject to
change without prior written
notice.
Follow the sequence below to
start a new diagnostic session.
HD III Quick Start Guide
Activate Connector
Serial Number
Activation Code
Activate