V1.00.001 2017-09-22 Note: This user manual applies to the following CReader models: CReader 6011, CReader 7001, CReader 7001F, CReader 8001, CReader 8011, CReader 8021 and CReader 9081. All illustrations and descriptions herein are only for reference. We reserve the right to make changes due to software update without prior written notice.
CReader Series English User’s Manual LAUNCH Trademark Information LAUNCH is a registered trademark of LAUNCH TECH CO., LTD. (LAUNCH) in China and other countries. All other LAUNCH trademarks, service marks, domain names, logos and company names referred to in this manual are either trademarks, registered trademarks, service marks, domain names, logos and company names of or are otherwise the property of LAUNCH or its affiliates.
CReader Series English User’s Manual LAUNCH Disclaimer To take full advantage of the unit, you should be familiar with the engine. All information, illustrations, and specifications contained in this manual are based on the latest information available at the time of publication. The right is reserved to make change at any time without notice.
CReader Series English User’s Manual LAUNCH engine is running. Keep the tool dry, clean, free from oil/water or grease. Use a mild detergent on a clean cloth to clean the outside of the tool, when necessary.
CReader Series English User’s Manual LAUNCH Table of Contents 1. Introduction ...................................................................................................... 1 2. General Information ......................................................................................... 2 2.1 On-Board Diagnostics (OBD) II.................................................................. 2 2.2 Diagnostic Trouble Codes (DTCs) ............................................................. 2 2.
CReader Series English User’s Manual LAUNCH 5.3.5 Diesel Particulate Filter (DPF) Regeneration (Only applies to CReader 7011F/9081) ............................................................................. 20 5.3.6 Tire Pressure Monitor System Reset (Only applies to CReader 9081) ................................................................................................................ 20 5.3.7 ABS Bleeding (Only applies to CReader 7011F/9081) .................... 21 5.3.
CReader Series English User’s Manual LAUNCH 1. Introduction Featuring a 4.0” color LCD and similar appearance, each of CReader 6011/7001/7001F/8001/8011/8021/9081 supports all 10 modes of OBD II test for a complete diagnosis. CReader 6011 In addition to the full OBDII/EOBD diagnostic functions, CReader 6011 also supports the diagnosis of the electronic control systems of vehicle, such as ABS and SRS.
CReader Series English User’s Manual LAUNCH cable. The memory card is highly recommended to update your tool. Note: CReader 6011/7001/7001F/8001/8011/8021/9081 may automatically reset while being disturbed by strong static electricity. THIS IS A NORMAL REACTION. 2. General Information 2.
CReader Series English User’s Manual LAUNCH Figure 2-1 2.3 Location of the Data Link Connector (DLC) The DLC (Data Link Connector or Diagnostic Link Connector) is typically a 16-pin connector where diagnostic code readers interface with the vehicle’s on-board computer. The DLC is usually located 12 inches from the center of the instrument panel (dash), under or around the driver’s side for most vehicles. If Data Link Connector is not located under dashboard, a label should be there telling location.
CReader Series English User’s Manual LAUNCH Figure 2-2 2.4 OBD II Readiness Monitors An important part of a vehicle’s OBD II system is the Readiness Monitors, which are indicators used to find out if all of the emissions components have been evaluated by the OBD II system. They are running periodic tests on specific systems and components to ensure that they are performing within allowable limits. Currently, there are eleven OBD II Readiness Monitors (or I/M Monitors) defined by the U.S.
CReader Series English User’s Manual LAUNCH engine system components require the vehicle to be operated under specific conditions before the monitor is ready. These monitors are termed non-continuous monitors and are listed below: 1) EGR System 2) O2 Sensors 3) Catalyst 4) Evaporative System 5) O2 Sensor Heater 6) Secondary air Injection 7) Heated Catalyst 8) A/C system 2.
CReader Series English User’s Manual LAUNCH 2.6 OBD II Definitions Powertrain Control Module (PCM) – It is the OBD II terminology for the on-board computer that controls engine and drive train. Malfunction Indicator Light (MIL) -- Malfunction Indicator Light (Service Engine Soon, Check Engine) is a term used for the light on the instrument panel.
CReader Series English User’s Manual LAUNCH RPM, vehicle speed, air flow, engine load, fuel pressure, fuel trim value, engine coolant temperature, ignition timing advance, or closed loop status. Fuel Trim (FT) -- Feedback adjustments to the base fuel schedule. Short-term fuel trim refers to dynamic or instantaneous adjustments. Long-term fuel trim refers to much more gradual adjustments to the fuel calibration schedule than short-term trim adjustments.
CReader Series English User’s Manual LAUNCH 3. Product Descriptions 3.1 Outline of CReader 6011/7001/7001F/8001/8011/8021/9081 Figure 3-1 CReader 6011/7001/7001F/8001/8011/8021/9081 Front View Note: CReader 6011/7001/7001F/8001/8011/8021/9081 feature same appearance. No. Name A DB-15 connector B Diagnostic cable 1 LCD Indicates test results. 2 DTC(F1) To read the DTCs. 3 4 (ESC) / Descriptions To connect the tool to the vehicle's DLC (Data Link Connector) via the diagnostic cable.
CReader Series English User’s Manual LAUNCH / Move cursor left or right for selection; Or turn page up and down when more than one page is displayed. 5 Memory card slot To insert the memory card to update your tool. 6 Mini USB port To connect to PC via USB cable for upgrading. 7 ER(F2) To erase the DTCs. 8 I/M(F3) I/M refers to Inspection and Maintenance that is legislated by the Government to meet federal clean-air standards.
CReader Series English User’s Manual LAUNCH 4. Connection & Settings 4.1 Connection 1. Turn the ignition off. 2. Locate vehicle’s DLC socket: Refer to Fig. 2-2 for the location. In case no DLC is found, please refer to Automobile Repair Manual. 3. Plug one end of the diagnostic cable into the DB15 connector of the tool, and connect the other end of the diagnostic cable into the vehicle’s DLC. 4. Turn the ignition on. Engine can be off or running. 5.
CReader Series English User’s Manual LAUNCH Figure 4-2 1) Language This option enables you to set the user interface language. Note: Due to continuous software upgrade, language interface may differ from different software versions. 2) Unit of Measure This option allows you to set measurement unit. 3) Beeper It is used to set On/Off the buzzer. 4) Record Mode It is used to turn On/Off the data stream recording function. Choose [Record Mode] and press [OK] to confirm.
CReader Series English User’s Manual LAUNCH 5.
CReader Series English User’s Manual LAUNCH 5.1 OBDII/EOBD Diagnosing This option presents a quick way to check for DTCs, isolate the cause of the illuminated Malfunction Indicator Lamp (MIL), check monitor status prior to emissions certification testing, verify repairs, and perform a number of other services that are emission-related.
CReader Series English User’s Manual LAUNCH Figure 5-3 It mainly includes the following functions: 1. Read Codes This option is used to identify which section of the emission control system has malfunctioned. 2. Erase Codes After reading the retrieved codes from the vehicle and certain repairs have been carried out, you can use this function to erase the codes from the vehicle. Before performing this function, please be sure the vehicle’s ignition key is in the ON position with the engine off.
CReader Series English User’s Manual LAUNCH meet federal clean-air standards. I/M Readiness indicates whether or not the various emissions-related systems on the vehicle are operating properly and are ready for Inspection and Maintenance testing. The purpose of the I/M Readiness Monitor Status is to indicate which of the vehicle’s Monitors have run and completed their diagnosis and testing (as described in Chapter 2.
CReader Series English User’s Manual LAUNCH The tool does not perform the leak test, but signals to vehicle’s on-board computer are to initiate the test. Before using the system test function, refer to the vehicle’s service repair manual to determine the procedures necessary to stop the test. 9. Vehicle Info This option displays the vehicle information, such as VIN (Vehicle identification Number), CID (Calibration ID) and CVN (Calibration Verification Number). 5.
CReader Series English User’s Manual LAUNCH Notes: This function does not apply to CReader 7001, CReader 7001F and CReader 9081. Before diagnosing, please make sure the diagnostic program corresponding to certain vehicle model has been installed on your tool. For vehicles manufactured by different manufacturers, it is possible that it has different diagnostic menus. 5.2.1 Read Vehicle Information This function is used to read the version information of system mode, vehicle VIN, software and ECU. 5.
CReader Series English User’s Manual LAUNCH Select “Diagnose” Follow the instructions on the screen to operate Select “Reset” (e.g. oil lamp reset etc.) Select the service mode (The available mode varies from vehicle to vehicle) Select the desired reset item (e.g. oil lamp reset etc.) Select the car brand Figure 5-6 (For CReader 7001/7001F/9081) For CReader 8001/8011/8021, the resetting function is loaded with each single vehicle model and can be done in process of the System Scanning operation.
CReader Series English User’s Manual LAUNCH 5.3.1 Oil Reset Service (Only applies to CReader 7001/7011F/8001/8011/ 8021/9081) This function allows you to perform reset for the engine oil life system, which calculates an optimal oil life change interval depending on the vehicle driving conditions and climate. This function can be performed in the following cases: 1. If the service lamp is on, you must provide service for the car.
CReader Series English User’s Manual LAUNCH and battery matching will be done. Battery matching must be performed in the following cases: a) Main battery is replaced. Battery matching must be performed to clear original low battery information and prevent the related control module from detecting false information.
CReader Series English User’s Manual LAUNCH 5.3.7 ABS Bleeding (Only applies to CReader 7011F/9081) This function allows you to perform various bi-directional tests to check the operating conditions of Anti-lock Braking System (ABS). 1. When the ABS contains air, the ABS bleeding function must be performed to bleed the brake system to restore ABS brake sensitivity. 2.
CReader Series English User’s Manual LAUNCH function must be performed so that the immobilizer control system on the car identifies and authorizes remote control keys to normally use the car. When the ignition switch key, ignition switch, combined instrument panel, ECU, BCM, or remote control battery is replaced, anti-theft key matching must be performed. 5.3.
CReader Series English User’s Manual LAUNCH 6. Help This menu enables you to view tool information and OBD introduction. In main menu, select [Help] and press [OK] to enter figure 6-1. Figure 6-1 6.1 DLC Location Information This option helps you to find the location of the vehicle’s DLC. 6.2 DTC Library In Figure 6-1, select [DTC Library] and press [OK] to enter the following screen.
CReader Series English User’s Manual LAUNCH Figure 6-2 Press []/[] button to move the highlight bar to different position. Press []/[] button to alter the value, then press [OK] button, the screen will display definition of the DTC. 6.3 Abbreviation This option allows you to view the full name and detailed explanation of the automotive glossary abbreviations. 6.4 Tool Information This option displays the related information of your tool. In figure 6-1, select [Tool Information] and then press [OK].
CReader Series English User’s Manual LAUNCH Figure 6-3 Note: You are strongly recommended to note down the Serial Number and Register Code in figure 6-3 since these 2 pieces of information are required while registering your tool. 6.5 About OBD This option allows you to have a general knowledge of OBD.
CReader Series English User’s Manual LAUNCH 7. Register & Update Prerequisite conditions: 1. System requirements: Windows XP, 7, 8 or Windows 10. 2. Go to http://mycar.x431.com, click “Products” -> “Creader Online” -> “CReader 6011/7001/8001/8011/8021/9081” to download the update tool and install it on the computer.
CReader Series English User’s Manual LAUNCH Figure 7-1 (For CReader 8001) Figure 7-1 (For CReader 8011) 27
CReader Series English User’s Manual LAUNCH Figure 7-1 (For CReader 8021) Figure 7-1 (For CReader 9081) There are 2 methods available to update your tool. You may choose one of the following to proceed. Method 1: Via Memory Card (recommended) 1.
CReader Series English User’s Manual LAUNCH Figure 7-2 2. In figure 7-2, type in the Product Serial Number (located at the back of the tool). Note: Once the S/N is entered, “Restore System” becomes activated, which is used to restore system if a new memory card is replaced. 3. Click [Device Upgrade] to enter the sign-up page. Enter the information and click [Submit] (refer to figure 7-3). Figure 7-3 (If you need the Register Code, please refer to steps 4~7.
CReader Series English User’s Manual LAUNCH 5. After the tool has powered up and entered the main menu screen, move the highlight bar on the “Help” icon and press [OK]. Figure 7-4 6. Highlight the “Tool Information” in figure 7-4 and press [OK].
CReader Series English User’s Manual LAUNCH 7. The Register Code shown in figure 7-5 is the Register Code needed in step 3. (Return to step 3 and input the Register Code and then proceed) 8. Install the memory card from the tool into the supplied memory card adaptor and insert into the USB port of the computer. 9. Reopen the update tool, select the updates you would like to perform or click "Select All", and then click [Download] to start downloading. 10.
CReader Series English User’s Manual LAUNCH Figure 7-7 3. Press [OK] to configure this tool as a USB device. See figure 7-8. Figure 7-8 Note: The Serial Number and Register Code shown in this figure are needed for inputting in Steps 4-6.
CReader Series English User’s Manual LAUNCH 4. Launch the update tool, a screen similar to figure 7-9 will appear. Figure 7-9 5. Type in the Serial Number. Click [Device Upgrade] to input the information and click [Submit] to enter the update page. Figure 7-10 6. Select the updates you would like to perform or click "Select All", and then click [Download] to start downloading. 7. Once all steps are complete, restart your tool. It will prompt you to upgrade, click [OK] to start updating.
CReader Series English User’s Manual LAUNCH 8. FAQ Here we list some frequently asked questions and answers relating to the tool. Question: System halts when reading data stream. What is the reason? Answer: It may be caused by a slackened connector. Please turn off the tool, firmly connect the connector, and switch it on again. Question: Screen of main unit flashes at engine ignition start. Answer: Caused by electromagnetic disturbing, and this is normal phenomenon.
CReader Series English User’s Manual LAUNCH Warranty THIS WARRANTY IS EXPRESSLY LIMITED TO PERSONS WHO PURCHASE LAUNCH PRODUCTS FOR PURPOSES OF RESALE OR USE IN THE ORDINARY COURSE OF THE BUYER’S BUSINESS. LAUNCH electronic product is warranted against defects in materials and workmanship for one year (12 months) from date of delivery to the user.
CReader Series English User’s Manual LAUNCH Statement: LAUNCH reserves the rights to make any change to product designs and specifications without notice. The actual object may differ a little from the descriptions in the manual in physical appearance, color and configuration. We have tried our best to make the descriptions and illustrations in the manual as accurate as possible, and defects are inevitable. If you have any question, please contact local dealer or after-sale service center of LAUNCH.
