Owner Manual
Printed in China
OPERATING INSTRUCTIONS
TROUBLESHOOTING
1-YEAR LIMITED WARRANTY
WARNING: Ensure the power is turned o to the fan/remote before performing any maintenance.
LED indicator on the remote illuminates, but the remote won’t control the fan. The remote may need to be re-synced.
The remote is synced to the receiver at the factory. Occasionally, power surges can cause the remote to become un-synced. Whenever necessary, follow the syncing instructions
below.
SYNCING INSTRUCTIONS: Switch the power to the fan o and back on again. Within 30 seconds, press and hold the HIGH SPEED and LOW SPEED buttons (or the “LEARN” button,
located in the battery compartment) for 5 seconds. Fan will turn on at low speed and light o. This conrms the syncing process is successful.
The LED indicator on the remote does not illuminate.
The battery most likely needs to be replaced or it is not oriented correctly in the battery compartment. If battery is depleted rapidly, ensure one of buttons is not stuck in the
down position.
The LED indicator stays on.
Ensure one of buttons is not stuck in the down position.
Remote controls more than one fan.
Turn o the power to the fans you don’t want synced. Follow the syncing instructions listed above. Then, turn on the power to the other fans.
Dimming feature does not function.
Ensure the bulbs are incandescent or other dimmable bulbs.
Fan will not run at high speed. If you fan has manual pull chains to operate the fan speed, be sure the pull chain is manually set to HIGH SPEED. If your pull chain is set to LOW or
MEDIUM SPEED, the remote will not override the manual pull chain setting.
Light will not turn on. If you fan has manual pull chains, be sure the light pull chain is set to ON. The remote will not override the manual pull chain setting.
The manufacturer warrants all of its lighting xtures against defects in materials and workmanship for one (1) year from the date of purchase. If within this period the product
is found to be defective, take a copy of the bill of sale as a proof of purchase and the product in its original carton to the place of purchase. The manufacturer will, at its option,
repair, replace or refund the purchase price to the consumer. All costs of installation and removal of the xture is the responsibility of the consumer. This warranty does not cover
xtures becoming defective due to misuse, accidental damage or improper handling and/or installation and specically excludes liability for direct, incidental or consequential
damages. As some states do not allow exclusions of limitations on an implied warranty, the above exclusion and limitation may not apply. This warranty gives you specic rights
and you may also have other rights which may vary from state to state.
Front Back
LED Indicator
High Speed
Medium Speed
Low Speed
Fan O
Light On/O
Light Delay
LEARN
Button
Variable Breeze
Home Shield
1. To operate the fan using the remote, makre sure fan
pull chain is on hight and light is turned on. Then press
and release the following buttons:
Fan O - Turns the power to fan o.
Light On/O - Turns the light on and o. Press and hold
to dim or brighten lights (for dimmable bulbs only).
High Speed - Turns on fan at high speed.
Light Delay - Light stays on for 60 seconds to allow
for safe exit from room. Note: Tap Light Delay once to
activate. Fan light blinks once to conrm Light Delay is
active. Press any button to cancel.
Medium Speed - Turns on fan at medium speed.
Variable Breeze - Simulates a breeze in nature. Press and
hold button to activate. Press any fan speed button to
cancel.
Low Speed - Turns on fan at low speed.
Home Shield - Simulates occupancy while away from
home. Fan remains o and the light randomly turns
on for a minimum of ve times and a maximum of 20
minutes. The light remains o for 60 minutes between
events. Press and hold button to activate. Light will blink
twice to conrm Home Sheild is active. Press any button
to cancel.
LED indicator should illuminate when any remote
button is pressed. If not, replace the DC3V, CR2032
batteries.