Owner Manual

MOUNTING AND WIRING INSTRUCTIONS
NOTE: Underwriters Laboratories (UL) does not require all fixtures to have ground wires. These fixtures
meet all UL specifications.
1. Turn off power at circuit box to avoid possible electric shock.
2. Thread mounting screws (A) into mounting bar (B) (see fig. 1) approximately 1/4 inch.
3. Secure lock washer (C) and nut (D) to nipple (A) on mounting bar (B).
4. Secure mounting bar (B) to outlet box (E) (horizontally or vertically, see fig. 1) with outlet box
screws (F) (if applicable).
5. To connect wires, take black fixture wire (group A from fig. 2) and place evenly against black outlet
box wire. Do not twist wires.
6. Fit wire connector (G from fig. 1) over wires and twist until there is a firm connection. If wire
connector (G) easily comes off, reattach and check again for a firm connection.
7. Repeat steps 5 and 6 with the white (group B from fig. 2) fixture and outlet box wires.
8. Partially thread green grounding screw (H) into side hole (I) on mounting bar (B) (see fig. 1).
9. Wrap ground wire from fixture around green grounding screw (H), leaving enough excess wire,
then connect ground wire and outlet box wire with wire connector (G) (if applicable).
10. Tighten green grounding screw (H). Do not over tighten.
11. Tuck wires inside outlet box (E).
FIXTURE ASSEMBLY INSTRUCTIONS
Warning: This fixture is for indoor use only.
1. Place back plate (J) over nipple (A).
2. Secure into place with cap nut(s) (K).
3. Install glass shade (L) and plate (if applicable) into holder(s) (M). Secure with thumb screws or
ring(s) (O), whichever is applicable.
4. Install lamp(s). Do not exceed recommended wattage.
5. Turn power back on at circuit box.
WARNING
Turn off electricity to the mounting site before beginning installation.
Mounting instructions must be followed exactly as shown for the fixture to be safely sup-
ported.
CLEANING AND CARE
To clean, wipe fixture with soft cloth. Clean glass with mild soap. Spray from chemical cleaners can
discolor the finish of fixture. Extend-A-Finish Laquer Conditioner, Item#70295, is recommended once
a year to clean, condition, and protect fixture. Do not use scouring pads, powders, steel wool or abra-
sive paper to clean this fixture.
NOTE FOR FIXTURES THAT ARE SOLID BRASS:
Your hand-crafted, solid brass lighting fixture has been coated with a durable, baked-on acrylic lac-
quer which gives maximum protection against the weather. However, in time the brightness of the
brass will tarnish, giving way to an authentic old-world brass finish. To keep your solid brass fixture
looking new for years to come, regularly apply a good quality, non-abrasive car wax to all metal sur-
faces, giving the fixture an extra protective covering.
ORDERING PARTS
Keep this manual for future reference, and in case replacement parts are needed. Available parts can
be ordered from place of purchase. Use exact wording from diagrams when ordering parts.
FIGURE 2.
GROUP A: GROUP B:
CONNECT TO BLACK
HOUSE WIRE
BLACK
WHITE OR GREY WITH TRACER
BROWN, GOLD OR BLACK
WITHOUT TRACER
BROWN, GOLD OR BLACK WITH TRACER
WHITE
WHITE OR GREY WITHOUT TRACER
CONNECT TO WHITE
HOUSE WIRE
NOTE: When parallel wire (SPT 1 & SPT 2) is used; the neutral wire is square shaped
and ridged, and the hot wire will be round in shape and smooth. (See below.)
WARRANTY INFORMATION
ASSEMBLY INSTRUCTIONS FOR INDOOR LIGHTING FIXTURE
NOTE: Carefully unpack fixture and parts. Make sure all parts are included before discarding any pack-
ing materials (see figure 1).
WARNING: ELECTRICAL SHOCK CAN RESULT IN SERIOUS INJURY.
Read and follow instructions exactly as shown. If instructions are unclear, do not proceed.
Contact a qualified electrician. Read all instructions before beginning. Proper wiring is essen-
tial for safe operation of this fixture. When cutting or drilling into walls or ceilings, do not dam-
age electrical wiring, gas lines, or water lines. If any of the fixture or wiring components are
damaged, do not install fixture. Return to place of purchase.
For fixtures provided with 75° C or 90° C supply wire warning only. (These warnings are pro-
vided on the U.L. label and on the fixture carton.) Risk of fire. Most dwellings built before 1985
have supply wires rated 60° C. Consult a qualified electrician before installing.
NOTE: For fixture employing a grounded convenience outlet. This fixture employs a grounded
type receptacle and is not intended for connection to a two wire ungrounded source of supply.
Applicable only to portable lamps:
To reduce the risk of electrical shock, all portable lamps have a polarized plug (one blade is
wider than the other). This plug will fit into a polarized outlet only one way. If plug does not fit,
reverse the plug. If it still does not fit, contact a qualified electrician. Never use with an exten-
sion cord unless plug can be fully plugged into the extension cord. Do not alter the plug.
Owner’s Manual
Indoor Lighting Fixture
Installation Instructions
Guide d’utilisation
Instructions d’installation
Appareil d’éclairage pour utilisation intérieure
GARANTIE LIMITÉE DE CINQ ANS
MISE EN GARDE:
L’ÉLECTROCUTION POURRAIT CAUSER DE GRAVES BLESSURES PERSONNELLES.
Lisez ces instructions et suivez-les exactement comme illustré. En cas de doute, ne commencez
pas l’installation. Consultez un électricien qualifié. Lisez toutes les instructions avant de com-
mencer l’installation. Un câblage approprié est essentiel au bon fonctionnement de cet appareil
d’éclairage. Lorsque vous faites une entaille ou que vous percez un trou dans un mur ou un pla-
fond, n’endommagez pas les câbles électriques, les canalisations de gaz ou d’eau. Si l’un des com-
posants de raccordement ou de l’appareil d’éclairage est endommagé, n’installez pas cet appareil
d’éclairage. Retournez-le à l’endroit où vous l’avez acheté.
Convient uniquement aux appareils comportant un avertissement indiquant que l’appareil
d’éclairage est doté d’un fil supportant une chaleur de 75°C ou 90°C. (Ces avertissements se trou-
vent sur l’étiquette U.L. et sur l’emballage de l’appareil d’éclairage.)
NOTA: Pour appareil d’éclairage avec sortie terre. Cet appareil d’éclairage utilise un réceptacle muni
d’un fil de terre et ne doit pas être branché à un bloc d’alimentation à deux fils non mis à la terre.
Ne s’applique qu’aux lampes portatives. Afin de réduire les risques d’incendie, toutes les lampes
portatives sont pourvues d’une fiche polarisée (une des broches est plus large que l’autre). La fiche
ne peut être branchée dans une prise polarisée que d’une seule manière. Si la fiche ne s’insère pas,
tournez-la dans l’autre sens. Si elle ne s’insère toujours pas, communiquez avec un électricien quali-
fié. N’utilisez jamais une rallonge électrique si la fiche ne peut être complètement insérée dans la
rallonge. N’essayez pas d’altérer la fiche.
LES INSTRUCTIONS D’ASSEMBLAGE DE L’APPAREIL D’ÉCLAIRAGE POUR UTILISATION INTÉRIEURE
NOTA : Déballez soigneusement l’appareil d’éclairage et les pièces. Assurez-vous que toutes les pièces y
sont avant de mettre l’emballage au rebut (voir fig. 1).
*NOT SUPPLIED
Line art shown may not exactly match the
fixture enclosed. However, the installation
instructions do apply to this fixture.
FIGURE 1.
RETAINING
RING (O)
GROUND
WIRE
LOCK
WASHER (C)
NIPPLE (A)
*OUTLET
BOX (E)
WIRE
CONNECTORS (G)
MOUNTING
BAR (B)
SIDE
HOLE (I)
OUTLET BOX
SCREWS (F)
GLASS
SHADE (L)
THUMB
SCREWS (N)
HOLDER (M)
BACK PLATE (J)
NUT (D)
GREEN GROUNDING
SCREW (H)
CAP NUTS (K)
Il est possible que le dessin illustré ici ne
soit pas la reproduction exacte de l’appareil
d’éclairage contenu dans la boîte.
Les instructions d’installation demeurent
cependant valables.
FIGURE 1.
LA BAGUE DE
RETENTION (O)
FIL DE MISE
A LA TERRE
RONDELLE DE
BLOCAGE (C)
MANCHON
FILETE (A)
*BOITE DE SORTIE
DE COURANT (E)
CONNECTEURS
DE FIL (G)
BARRE DE
FIXATION (B)
TROU
LATERAL (I)
VIS DE LA BOITE DE
SORTIE DE COURANT (F)
ABAT-JOUR
EN VERRE (L)
VIS A CLE (N)
SUPPORT (M)
PLAQUE
ARRIERE (J)
ECROU (D)
VIS DE MISE
A LA TERRE
(VERTE) (H)
ECROU
CAPUCHON (K)
PLATE
(if applicable)
PLAQUE
(s’il y a lieu)