FIT CLOSET Installation Instructions
••• TABLE OF CONTENTS PAGE 02 PAGE 03 PAGE 05 PAGE 08 PAGE 11 PAGE 12 PAGE 13 ••• Installation Preparation Assembly Parts Closet Unit Installation Intro Drawer Installation Hang Rod Installation Adjustable Shelf Installation Toe Kick Installation
I N STA LL ATI ON PREPAR ATION ••• TO O L S NE E DED : Tape Measure Screw Driver (#2 Phillips Drill Bit) #2 Square Bit Drill (#2 Phillips Drill Bit) Level Rubber Mallet P R E PAR E YOUR S PAC E: Take an inventory of necessary parts. Prior to installation, remove baseboard.
AS S E MB LY PARTS ••• 8mm Flat Rafix Bolt Connects fixed shelves to panel. #6 5/8” Wood Screw Mends plates to connect the connector panels, install L-Brackets to panels, and used for back holds on drawer slides in place of Euro Screws. 5mm x 10.5mm Euro Screw Attches drawer slides to panel. Front Safety Shelf Pin For adjustable closet shelves. Back Safety Shelf Pin For adjustable closet shelves. L-Bracket Attaches unit to wall. Install above the top, fixed shelf.
L-BR ACK ET ••• ¼” spacing from wall on top of fixed shelf Wood screws installed into top fixed shelf 04
CLOSE T U NI T INSTALL ATION 1. Add Rafix cups to fixed shelves. 2. Add Rafix bolts where fixed shelves are installed. ••• 3. Tighten Rafix cups with a #2 Phillips screwdriver.
U ND E RSTANDING UN ITS ••• Your closet consists of upright partitions and fixed shelves. A “unit” is a section between any pair (left and right) partition. Assemble one unit at a time in segment from one side to the other after installing all Rafix cups and Rafix Bolts where necessary.
U N IT INSTALL ATION STEPS ••• Step 1. Begin assembly with the partition that is going up against the wall. Lean partition up against the wall with finished edge facing you. Step 2. Place the additional partitions that make up the rest of the unit against the wall with holes facing you. Step 3. After all your partitions are set in place, go back to the beginning partition with a fixed shelf, and lock your Rafix cups into the top Rafix bolts with a screwdriver to hold in place. Step 4.
D R AWE R IN STALL ATION STEPS ••• Step 1. Each drawer slide set is made of two pieces and each set can be used interchangeably. Step 2. Take one set and fully extend the inner rail. Step 3. Locate the black tab and adjust with your thumb. Step 4. Fully extend the black tab while simultaneously pulling apart. Step 5. Now that your two pieces are separated you are ready to install.
PL ACE ME N T OF DR AWER SLIDES ••• Step 1. Start from the 2nd to the bottom hole on the partition. Insert two Rafix bolts for the placement of the bottom fixed shelf. Step 2. The first drawer slide will be installed at the 3rd hole from bottom. Rafix Bolt Drawer Slide Drawer Slide Rafix Bolt Drawer Slide Drawer Slide Rafix Bolt Step 3. The second drawer slide will be installed at the 10th hole from bottom. Step 4. Install the Rafix bolts at the 16th hole from the bottom for the fixed shelf. Step 5.
D R AWE R H ANDLE & KN OB ••• 1. Measure to find the center of drawer front. Center the handle with the center mark. 2. Mark the center. Place knob in the center.
H AN G ROD I N STALL ATI ON 1. Install the rod bracket starting at the second hole below the fixed shelf. ••• 2. Insert the rod in between both pairs of rod brackets.
A D J U STA BL E S H EL F I N STA L L AT I O N ••• Front adjustable pin Back adjustable pin Place the shelf hole on top of front shelf pin Place the back shelf on top of back shelf pin 12
TO E K ICK I N STALL ATI ON ••• Toe kicks are already sized and cut to fit your units. Simply apply the double stick tape included with your hardware to the back of your toe kicks and install on your units.
