Assembly Instructions

ManualsBrandsLatitude Run ManualsFurnitureAaric TV Stand for TVs up to 65"

P.1

Summary of content (29 pages)

PAGE 1
Assembly Instructions P.
PAGE 2
General Assembly Guidelines I. Ensure that all parts and hardware are available before beginning assembly. II. Follow each step carefully to ensure the proper assembly of this product. III. Two people are recommended for ease in the assembly of this product. IV. The three main types of hardware used to assemble this product are: wood dowels, screws and bolts. The provided glue is to secure wood dowels in place.
PAGE 4
Hardware List A Ø8x30mm Wooden dowel 21 pcs B Ø6x35mm Cam bolt 20 pcs C Ø15x11mm Cam lock 20 pcs D Ø30mm Sticker 16 pcs E Ø6x50mm Screw 10 pcs F Ø1/4x12mm Bolt 16 pcs G Ø1/4x25mm Bolt 6 pcs H Ø1/4x25mm Bolt 1 pc Glue tube 1 pc J K Ø4x12mm Screw 17 pcs L Ø3.
PAGE 5
Step 1 A A A A A A B 11 12 13 B A A A A A A A A A A A A 6 8 7 24 A Insert wooden dowel (A) into parts (6,7,8,11,12,13,24) ,then using cam bolt (B) secure part (11) with Philips head screwdriver as per diagram. All rights reserved. P.
PAGE 6
Step 2 B B B B 1 B B B B B B B B 9 B B B B 14 B B 23 A A Insert wooden dowel (A) into part (14) ,then using cam bolt (B) secure parts (1,9,23) with Philips head screwdriver as per diagram. All rights reserved. P.
PAGE 7
Step 3 Slider arm Slider arm V V Slider bracket Slider bracket Pick up the slider arm (V) and separate the slide Runner for the following Steps. Extend the Slide .Runner all the way forward,press the plastic release lever of the alider arm up and pull the Slide Runner Complete out . All rights reserved. P.
PAGE 13
Step 9 E E H 4 7 15 E E 3 G P Using bolt (E) attach parts (3,4) to part (7) ,bolts (G,H) attach parts (3,4) to part (15) with hex key (P) as per diagram. Note: Do not fully tighten all bolts until you finish assembling all parts, once assembled, go back and fully tighten all bolts. All rights reserved. P.
PAGE 18
1 Step 14 2 3 1 5 F C C 6 F 8 C 7 P C C Using cam lock (C) secure part (1) into parts (6,7,8) with Philips head screwdriver ,then using bolt (F) attach part (5) to part (1) with Hex key (P) as per diagram. All rights reserved. P.
PAGE 21
1 Step 17 2 20 21 3 24 19 22 20 C 19 24 C C 23 Put part (22) as per diagram. Then using cam lock (C) secure part (23) to parts (19,20,24) with Philips head screwdriver as per diagram. All rights reserved. P.
PAGE 22
Step 18 V D D 23 Place sticker (D) as per diagram. Insert the assembled drawer into the unit frame, extend the Ball Bearing Slide Tracks (V) on the pedestal Side Panel all the way forward .Then align the Slide Runners on the assembled drawers with the Slide Tracks and push the drawer carefully inside until it stops. Note : if the drawer does not go in smoothly, please take it out and repeat the step.
PAGE 28
1 Step 24 2 3 WARNING Serious or fatal injuries can occur from furniture tipping over. To prevent the furniture from tipping over we recommend that it is permanently fixed to the wall. Wall anchor and hardware are included with this product. Please make sure hardware is suitable for your walls before installing, as different wall materials may require different types of anchors. Wall S Q R Using screw (R) attach Velcro strap (Q) into Nut (S) to wall with Philips head screwdriver as per diagram.