Installation & Assembly

ManualsBrandsLatitude Run ManualsBathroom Remodel & Bathroom FixturesWalbrook 28" Single Bathroom Vanity Top in Matte White with Sink

Table Of Contents

Side view for plumbing

Features:

Drawers push-open and soft-close

Handleless ergonomic continous drawer

Includes fully adjustable drawersliders

Fully finished interiors

Includes installation hardware

Micro-Density Fiberboard (MDF) construction

PVC finish resists moisture and scratches

Back view for plumbing

17,8

13,7

11,8

Wall

16,2

16,6

16,2

17,8

13,7

11,8

5,5

Wall Wall

5 25.6

9.5

6.5

3.8

17,8

27,5

7,9 - 11,8

19,6

17,7

33,5

Summary of content (9 pages)

PAGE 1
Features: Drawers push-open and soft-close Handleless ergonomic continous drawer Includes fully adjustable drawersliders Fully finished interiors Includes installation hardware Micro-Density Fiberboard (MDF) construction PVC finish resists moisture and scratches Side view for plumbing Back view for plumbing 5 3.8 Wall 20 25.6 4 17,8 6.5 9.
PAGE 2
7,9 41,7 41,7 28 41,8 41,8 20 20 17,8 20 27,5 17,8 27,5 16,5 13,7 17,8 5 27,5 13,7 12,7 23,6 24,5 55,5 55,6 55,6 55,6 55,6 17,8 27,5 17,8 20 20 20 20 27,5 13,7 13,7 13,7 17,8 13,7 17,8 27,5 13,7 27,5 69,3 69,4 69,4 69,4 20 20 27,5 20 27,5 17,8 27,5 13,7 17,8 13,7 27,5 27,5 17,8 27,5 13,7 13,7 27,5
PAGE 3
Installation notes: Install this product according to the installation guide Special site preparation is required. The plumbing must be roughed into the plumbing cutout area of the vanity. Refer to the sink rough-in and the vanity rough-in for proper placement. The water supply and drain lines must be installed before installing the vanity.
PAGE 4
Step 1 Pull out completely the drawers and take off from the slide rails. Step 2 Determine the ideal location of your new vanity. Mark the holes and drill pilot holes in the dry wall. 1 2 X Y Step 3 Place the wall brackets on the finished wall and install at the locations drilled with the screws as shown here. 3 X Y According to measures taken on step 2, make drills with diameter 0,3in. For each wall plate must be made 4 holes. Then insert nylon rawlplug for each drill.
PAGE 5
4 Step 4 It is possible to adjust the vanity using the adjusting screws. Step 5 Fully extend the slide rails out. Place the drawer into the slide rails. To secure drawer, close the drawer until a series of clicks are heard.
PAGE 6
Installation notes: Faucet and silicone are not included. All sizes are subject to tolerance. Sink assembly Install the faucet to the top and drains to the sink. Refer to the faucet and drain manufacturer’s instructions. Complete the faucet connections. Run water and check for leaks. Apply a bead of silicone behind the top surface to the finished wall.
PAGE 7
Installation notes: Faucet and silicone are not included. All sizes are subject to tolerance. Sink assembly Install the faucet to the top and drains to the sink. Refer to the faucet and drain manufacturer’s instructions. Complete the faucet connections. Run water and check for leaks. Apply a bead of silicone behind the top surface to the finished wall.
PAGE 8
Installation notes: Faucet and silicone are not included. All sizes are subject to tolerance. Sink assembly Install the faucet to the top and drains to the sink. Refer to the faucet and drain manufacturer’s instructions. Complete the faucet connections. Run water and check for leaks. Apply a bead of silicone behind the top surface to the finished wall.
PAGE 9
Installation notes: Faucet and silicone are not included. All sizes are subject to tolerance. Sink assembly Install the faucet to the top and drains to the sink. Refer to the faucet and drain manufacturer’s instructions. Complete the faucet connections. Run water and check for leaks. Apply a bead of silicone behind the top surface to the finished wall.