TOOLS REQUIRED Phillips Screwdriver (Not Included) Hammer (Not Included) 2 - Persons Recommended ASSEMBLY RATING EASY DIFFICULT The Assembly Rating is a 5-point system showing the level of effort needed to assemble a specific product.
/ 14
/ 14
ASSEMBLY CARE ADVICE FAILURE TO FOLLOW THE GUIDELINES BELOW MAY RESULT IN INJURY AND/OR PROPERTY DAMAGE. Turn clockwise to tighten and only tighten when step is completed or when instructed to do so. Position each part correctly and insert screws or bolts into their respective holes. Use the appropriate hand tools or power tools for assembly. Select steps, such as tightening screws and/or bolts, may require hand tools to avoid causing damage during assembly.
/ 14
NIGHTSTAND A G J F K E C B PARTS A 1PC E 1PC B 1PC J 1PC O 1PC K 2PCS P 1PC L 2PCS Q 2PCS M 2PCS R 1PC G 1PC D 1PC H 1PC ACCESSORIES HARDWARE 1 22PCS 2 22PCS 3 26PCS 4 8PCS A1 2PCS 6 4PCS A2 2PCS 0.87" 1.25" 0.59" N 2PCS F 1PC C 1PC 5 4PCS I 1PC 7 4PCS 0.
GET READY Please group boards as below.
1 1 1 Hardware 1 x14PCS Hardware 3 x4PCS 1 1 A 1 1 1 1 B 1 C 1 1 1 1 D 1 E 3 A5 3 OPTIONAL 3 Apply a dab of glue into dowel holes of panels before inserting dowels (#3).
2 1 1 Hardware 1 x8PCS Hardware 3 x22PCS 3 3 F 3 3 3 3 1 1 3 3 A5 3 OPTIONAL G 3 Apply a dab of glue into dowel holes of panels before inserting dowels (#3).
3 Part B Part C Part D Part E Part F Part G 2 E x1PC x1PC x1PC x1PC x1PC x1PC 2 Top 2 F Front 2 A3 B Hardware 2 x8PCS A3 2 Accessory A3 x4PCS C 2 2 Top G Front 2 A3 D A3 4 Part H Part I Part J Part P 1 x1PC x1PC x1PC x1PC Hardware 2 x3PCS Front Top 2 Please refer to page 5 for detailed instructions on how to fasten cam locks (#2) to cam bolts (#1).
5 Hardware 2 x3PCS Front Top C D G J 2 2 H P 2 I 1 2 6 Top Front 3rd Part A x1PC Part O x1PC Part R x1PC A Hardware 2 x4PCS 1st 2 Accessory A4 x4PCS R O 2 2 F Use the provided stickers (#A4) to cover exposed locks.
7 Part K Part L Part M Part N Part Q Top Front x1PC x1PC x1PC x1PC x1PC M Q Hardware 2 x4PCS Hardware 4 x8PCS L 2 K Accessory A1 x2PCS Accessory A2 x2PCS X2 1 2 2 4 4 N M 4 4 L X2 Top Front Top Front A2 X2 K A1 12 / 14
8 Top Hardware 5 x4PCS Front 5 5 K K Fully extend drawer rails then align the rails smallest hole to the drawer slide panels holes. Secure with bolts (#5). X4 9 Top Hardware 6 x4PCS Hardware 7 x4PCS Front 6 7 R Insert fixative plates (#6) through the thin lined gaps between back and side panels, then secure by using screws (#7).
10 ASSEMBLY COMPLETED Please ensure the furniture rests on an even and flat surface. If the produst wobbles or feels loose,double-check all bolts and/or screws are properly tightened and secured. Keep this handy! Please retain this instruction manual and any order-related information for future reference.
