READ AND SAVE THESE INSTRUCTIONS Ceiling Fan Owner's Manual Net Weight: 18.3 Lbs.
! WARNING WARNING: To avoid fire, shock, and serious personal injury, follow these instructions. Safety Instructions 1. Read your owner’s manual carefully and keep it for future reference. 2. Before servicing or cleaning unit, switch power off at service panel and lock service panel disconnecting means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a warning device, such as a tag, to the service panel. 3.
QUICK START GUIDE The Quick Start Guide covers the installation instructions common for ceiling fan operations. If additional assistance with wiring, alternate hanging systems, or lighting options, proceed to the complete instructions of this Owner’s Manual. The Quick Start Guide sections include page numbers to correspond with the appropriate sections of the Owner’s Manual for detailed instructions. * See Unpacking Instructions for a complete list of parts for installation.
QUICK START GUIDE How to Put Your Ceiling Fan Together (pages 9 & 10) 1. Remove the 10-24 x 3/8” pan head screw with lockwasher nearest the hook from the ceiling mounting plate and retain for later use. Loosen the remaining two 10-24 x 3/8” pan head screws several turns. KEY HOLE SLOT 2. While still attached to the mounting plate hook, pivot the fan motor assembly upwards and mate it up against the ceiling mounting plate. Align and engage the two keyhole slots with the two loosened screw heads.
QUICK START GUIDE How to Put Your Ceiling Fan Together (pages 10 & 11) 11. Attach one blade assembly to the motor using the two 1/4-20 x 9/16” captive flange screws with lockwashers. Make sure the screws are tightened securely. Repeat this procedure for the other four blade assemblies. BLADE FLANGE ASSEMBLY NOTE: Take care not to scratch the fan housing when installing the blade assemblies. 1/4-20 x 9/16" CAPTIVE FLANGE SCREW WITH LOCKWASHER (2 sets per flange) 12.
This Manual Is Designed to Make it as Easy as Possible for You to Assemble, Install, Operate and Maintain Your Ceiling Fan Installed Wire Length Up to 50 ft. 50-100 ft. Tools Needed for Assembly One Phillips head screwdriver One 1/4” blade screwdriver One stepladder One wire stripper MATERIALS WARNING ! Wiring outlet box and box connectors must be of type required by the local code. The minimum wire would be a 3-conductor (2-wire with ground) of the following size: Wire Size A.W.G.
Electrical Requirements Your new ceiling fan will require a grounded electrical supply line of 120 volts AC, 60 Hz, 15 amp circuit. The ceiling structure must be capable of reliably supporting at least 50 pounds. ! ! WARNING Turning off wall switch is not sufficient. To avoid possible electrical shock, be sure electricity is turned off at the main fuse box before wiring.
How to Hang Your Ceiling Fan (continued) 1. Disconnect electrical power to the branch circuit at the circuit breaker or fuse box before attempting to install the ceiling fan mounting plate on the outlet box. 2. Pull the electrical supply black white, and ground wires through the center opening of the ceiling mounting plate before securing the plate to the outlet box as shown in Figure 2. CEILING AT LEAST 7' 3.
How to Put Your Ceiling Fan Together 1. Remove the 10-24 x 3/8” pan head screw with lockwasher nearest the hook from the ceiling mounting plate and retain for later use. Loosen the remaining two 10-24 x 3/8” pan head screws several turns. KEY HOLE SLOT 2. While still attached to the ceiling mounting plate hook, pivot the fan motor assembly upwards and mate it up against the ceiling mounting plate.
How to Put Your Ceiling Fan Together (continued) 9. Push the trim ring upwards and rotate so that it engages and locks onto the four mounting screw heads of the fan housing cover (Figure 9). MOUNTING SCREW HEADS 10. Mount the blade flanges to the fan blades using three 10-24 x 5/16” washer head blade screws per blade (supplied) (Figure 10). Repeat for the four remaining blades.
How to Put Your Ceiling Fan Together (continued) 14. Position the switch housing assembly on the switch housing plate and align the holes in the switch housing assembly with the holes in the plate. Secure the switch housing assembly by reinstalling the four screws removed previously (Figure 13). SWITCH HOUSING ASSEMBLY MOUNTING SCREWS (4) Figure 13 Operating Your Ceiling Fan 1. All fans are shipped from the factory with the reversing switch positioned to circulate air downward.
Wall Control Installation This control is designed to operate only one ceiling fan, and not an accessory light kit. This wall control is rated for 1.2 amps at 120 volts. NOTE: The “0” position is OFF. The four fan speeds are selected by sliding the bar to the other four speed positions (“1”, “2”, “3” and “4”). ! WARNING Turning off wall switch is not sufficient. To avoid possible electrical shock, be sure electricity is turned off at the main fuse box before wiring.
Energy Efficient Use of Ceiling Fans Ceiling fan performance and energy savings rely heavily on the proper installation and use of the ceiling fan. Here are a few tips to ensure quality and product performance. Using the Ceiling Fan Year Round. In the summer, use the ceiling fan in the counter-clockwise direction. The airflow produced by the ceiling fan creates a wind-chill effect, making you "feel" cooler. Select a fan speed that provides a comfortable breeze, lower speeds consume less energy.
Trouble Shooting ! WARNING: For your own safety, turn off power at fuse box or circuit breaker before trouble shooting your fan. TROUBLE 1. Fan will not start. PROBABLE CAUSE SUGGESTED REMEDY 1. Fuse or circuit breaker blown. 1. Check main and branch circuit fuses or circuit 2. Loose power line connections to the fan, 2. Check line wire connections to fan and switch breakers. or loose switch wire connections in the switch housing. wire connections in the switch housing.
Repair Parts Key No.
LIMITED WARRANTY
