Installation Guide

32
Hub Installation Guide Version 1.0
33
Industry Canada (IC) Compliance Statement
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation,
Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to
the following two conditions: (1) This device may not cause interference, and (2) this device
must accept any interference, including interference that may cause undesired operation of
the device.
To satisfy RF exposure requirements, this device and its antenna must operate with a separation
distance of at least 20 centimeters from all persons and must not be co-located or operating in
conjunction with any other antenna or transmitter.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio
exempts de licence. L’exploitation est autorisée aux deux conditions suivantes:
1.
L’appareil ne doit pas produire de brouillage, et
2.
L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est
susceptible d’en compromettre le fonctionnement.
Pour remplir les conditions requise sur l’exposition des fréquences radios, cet appareil et les
antennes doivent fonctionner avec une distance minimum de 20 centimètres avec toutes les
personnes et ne doivent pas être placés ou fonctionner en conjonction avec tout autre antenne
ou émetteur.
Troubleshooting
If the hub does not operate:
•
Ensure the hub is powered with DC power. Do not use AC power.
•
Ensure the input voltage if using 2 wire is 12 volts DC
•
Further troubleshooting information is available on the support website at support.latch.com
•
Safety Instructions
•
This product shall be installed and serviced by certified professionals only
•
Locations and wiring methods shall be in accordance with the National Electrical Code,
ANSI/NFPA 70
•
Power Sources for Class 2 and Class 3 Circuits
•
There are no replacement parts available for this product
•
Correct wiring insulation should be used during installation to prevent the risk of electrical
•
shock
Safety Instructions
Configuration & Commissioning instructions can be found in more detail in the Technical
Certification Training as well as on the support website at support.latch.com
Service Information
Configuration & Commissioning instructions can be found in more detail in the Technical
Certification Training as well as on the support website at support.latch.com
Applicable Products
This installation guide applies to products with the following designators on the label:
•
Model: Hub
Warning
•
The product may contain an internal lithium manganese dioxide, vanadium pentoxide, or
alkaline battery or battery pack. There is risk of fire and burns if the battery pack is not
handled properly.
•
Do not expose to temperatures higher than 50° C (122° F).
•
To reduce potential safety issues, only the battery provided with the product, a replacement
battery provided by Latch, or a compatible battery purchased as an accessory from Latch
should be used with the product.
•
To reduce the risk of fire or burns, do not disassemble, crush, puncture, short external
contacts, or dispose of in fire or water.
•
Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries
according to the instructions.
•
Do not ingest battery, a Chemical Burn Hazard.
•
Keep new and used batteries away from children.
•
If the battery compartment does not close securely, stop using the product and keep it away
from children.
•
If you think batteries might have been swallowed or placed inside any part of the body, seek
immediate medical attention.
•
Leaving a battery in an extremely high temperature surrounding environment can result in an
explosion or the leakage of flammable liquid or gas.
•
A battery subjected to extremely low air pressure may result in an explosion or the leakage of
flammable liquid or gas.
Exposure to Radio Frequency (RF) Energy
This device meets the government’s requirements for exposure to radio waves. This device is
designed and manufactured not to exceed the emission limits for exposure to radio frequency
(RF) energy set by the Federal Communications Commission (FCC) and the Innovation, Science,
and Economic Development (ISED) Canada.
Industry Canada (IC) Compliance Statement
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation,
Science and Economic Development Canada's licence-exempt RSS(s). Operation is subject to
the following two conditions: (1) This device may not cause interference, and (2) this device
must accept any interference, including interference that may cause undesired operation of
the device.
To satisfy RF exposure requirements, this device and its antenna must operate with a separation
distance of at least 20 centimeters from all persons and must not be co-located or operating in
conjunction with any other antenna or transmitter.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio
exempts de licence. L'exploitation est autorisée aux deux conditions suivantes:
1. L'appareil ne doit pas produire de brouillage, et
2. L'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est
susceptible d'en compromettre le fonctionnement.
Pour remplir les conditions requise sur l'exposition des fréquences radios, cet appareil et les
antennes doivent fonctionner avec une distance minimum de 20 centimètres avec toutes les
personnes et ne doivent pas être placés ou fonctionner en conjonction avec tout autre antenne
ou émetteur.
The device for operation in the band 5150 -5250 MHz is only for indoor use to reduce the potential for harmful
interference to co-channel mobile satellite systems.
Les dispositifs fonctionnant dans la bande 5150-5250 MHz sont réservés uniquement pour une utilisation à
l'intérieur afin de réduire les risques de brouillage préjudiciable aux système de satellites mobiles utilisant les
même canaux.