Hub Installation Guide
Table of contents Document number 770-00015 Revised on 08/26/2020 Things you should know 04 Included in the box 05 Product details 07 Installation 19 Specifications 30 Requirements for compliance 31
Things you should know Included in the Box Mounting Hardware • Pan-head screws • Anchors • Cable ties Product • • • • Latch Hub Mounting Plate Wire Grommet Cover Not Included in the Box Mounting Tools • #2 Phillips head screwdriver • T25 Torx screwdriver • 1/4” drill bit For in-unit install, place the hub near the media panel. Requirements for Device Configuration requires the iOS Manager App running on an iPhone 5S or newer.
Product Details Details and recommendations for power, wiring, and product specifications. 6 Hub Installation Guide Version 1.
LED (Light) Definitions I/O Port Definitions Power Reset Ethernet Solid White - Online and connected Flashing White - Booting up, connecting, or pairing Fast Flashing White - Firmware updating Solid Red - Cannot connect to Latch servers No Light - Power off or battery out 8 Hub Installation Guide Version 1.
Wiring Requirements DC Power Adapter Input voltage: 90 - 264 VAC Input frequency: 47 - 63 Hz Output voltage: 12 VDC +/- 5% Max load: 2 AMPs Min load: 0 AMPs Load regulation: +/- 5% 2.5mm barrel jack 5ft cable length Note: Do not splice DC power adapter 10 Hub Installation Guide Version 1.
Wiring Optional Cable Extension 5ft cable length 5ft cable length Sold Separately. Note:If the DC power adapter (5ft) is not long enough for installation, an additional 5ft extension cable can be used. Only one extension per hub is supported. 12 Hub Installation Guide Version 1.
Wiring Minimum Wire Gauge Per Length of Wire Run Low Voltage 2 Wire Power Distance Power (12v) < 25ft < 50ft 24 AWG 22 AWG < 100ft 18 AWG < 200ft 14 AWG In- Building 12VDC > 24 Watts Power Supply *Class 2 Isolated, UL Listed 14 Hub Installation Guide Version 1.
Installation Follow these steps to proceed with installation. 18 Hub Installation Guide Version 1.
1. Rotate Torx screws in outer Cover counter-clockwise clockwise to unlock. Separate the outer Cover from the Mounting Plate using the opening on the underside. Note: Do not use a power tool or excessive force on the Torx screws—over torquing could cause damage. Rotate Torx screws in Hub counter-clockwise counter to unlock. Remove the Hub from the Mounting Plate. 20 Version 1.
2. Attaching to junction box Attaching to wall or ceiling Install Mounting Plate. Attach to junction box or attach to wall or ceiling. Note: Pass cables through opening before attaching Mounting Plate to junction box. 22 Version 1.
3. Attach Hub to Mounting Plate by aligning mating features. Rotate Torx screws in Hub clockwise to lock. 24 Version 1.
4. Plug in power and Ethernet cables. Use included cable ties to secure. Install Grommet. Junction box scenario. 26 Version 1.
5. 6. Use Latch Manager App to setup the device. Observe and monitor LED to verify set up success. Install the outer Cover aligning with Mounting Plate and Grommet. Rotate Torx screws clockwise to lock and secure Cover. 28 Version 1.
Specifications Regulatory Compliance Dimensions Federal Communications Commission (FCC) Compliance Statement • Dimensions: 8 in. x 8 in. x 2.25 in. • Weight: 3.3 lbs. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Industry Canada (IC) Compliance Statement Industry Canada (IC) Compliance Statement This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, This device contains Development licence-exempt transmitter(s)/receiver(s) comply with Innovation, Science and Economic Canada's licence-exempt RSS(s). that Operation is subject to the following conditions: (1) This device may not cause interference,RSS(s).
