How to Guide

MODEL 2535
Rev. A 9/04
3
2535ES
Rev. A 9/04
6
2535ES
REMOTE CONTROL (Figure 6)
1. Install the two “AAA” batteries supplied as shown in Figure 6 .
2. The Remote Control Power Button is labeled as (
).
3. All the functions performed with the Remote Control work
identically to the Manual Controls.
ARMADO DE LA TUBERÍA (Figura 1)
1. Saque el conjunto de la tubería del cartón como muestra. (Paso 1)
2. Desafloje la Tuerca De Ajuste De Altura, girando en sentido
contrahorario.
(Paso 2)
3. Eleve la Extensión De La Tubería. (Paso 3)
4. Apriete la Tuerca De Ajuste De Altura, girando en sentido horario.
(Paso 4)
MAINTENANCE
WARNING: ALWAYS UNPLUG THE CORD BEFORE MOVING
OR SERVICING.
WARNING: DO NOT IMMERSE FAN IN WATER!
CLEANING: Clean the Fan with the vacuum brush attachment
on your vacuum cleaner. This will remove dirt and lint that may
accumulate over time. DO NOT ATTEMPT TO TAKE APART FAN.
Clean the body of the Fan with a soft cloth.
CAUTION: Do not use gasoline, benzine, thinner, harsh clean-
ers, etc. as they may damage the Fan. NEVER use ALCOHOL
OR SOLVENTS.
SERVICING: All other servicing, with the exception of general user
maintenance, should be performed by an authorized service repre-
sentative. Call 1-800-233-0268, Monday through Friday, between the
hours of 8:00 a.m. and 5:00 p.m. EST for the location of your nearest
service center.
STORAGE: Store the Fan, with these instructions, in a cool, dry place.
LOUVER FUNCTION (Figure 7)
In addition to the oscillation function, this Fan has louvers on the
front grill that allow for vertical adjustment of air flow. Roll the louver
control (Inset 7A) up or down to adjust the air flow as desired.
MODEL 2535
MODELO 2535
Figura 1
Extensión De
La Tubería
Tuerca De
Ajuste De
Altura
Paso 1
Paso 3
Paso 4
Paso 2
Extensión De
La Tubería
Tuerca De
Ajuste De
Altura
Figura 2
(5) Tornillos #8 X 1/2”
Copas
PARTE INFERIOR DE LA BASE
Orificios
De Copa
ARMADO DE LA BASE (Figura 2)
1. Arme la Base entrecerrando las Copas en los Orificios De Copa
situados en la Parte Inferior De La Base.
2. Fije (5) Tornillos #8 X 1/2” en los Orificios De Copa en la Parte
Inferior De La Base.
OPERATION
This Fan may be operated by the Manual Controls located on top of
the unit (as shown in
Figure 5 ) or by the Remote Control (shown in
Figure 6) .
1. Remove the Fan from the carton and assemble as instructed.
2. Place the Fan on a firm, level surface.
WARNING: Plastic or rubber tabs, like the feet on this unit, may
stick to hardwood floors. The unit may leave a residue that could
darken, stain or leave permanent blemishes on the finish of certain
hardwood floors.
3. Plug the power supply cord into a 120 V~ electrical outlet. Be
sure plug fits tightly in outlet.
4. When the Fan is plugged in, there will be a “beep” to indicate
there is power to the unit.
5. Turn the Fan ON by pressing the Power Button (
). The Fan will
“beep” twice to indicate that the unit has been turned ON.
6.
SPEEDS: Press the Fan Speed Button ( ) to desired speed
setting. Each time the Fan Speed Button is pressed, the speed
will change from Low (1), to Medium (2), to High (3). When intially
plugged in, the Fan will be in Low Speed. When the Fan is turned
OFF and ON again, the unit will resume the speed at which it
was turned OFF.
7.
OSCILLATION: Press the Oscillation Button ( ) to start and
stop the oscillation function.
8. TIMER: The timer function allows the unit to be set to operate
for a length of time from 1/2 hour to 7 1/2 hours, in increments of
a 1/2 hour. Press the Timer Button (
) to set the length of time
desired. Each time the timer button is pressed, the time is
increased by 1/2 hour. After reaching 7 1/2 hours, pressing the
timer button once more will reset the Fan to continuous running.
The lights on the front of the unit will light up appropriately with
the length of time that the Fan is set for.
9.
SLEEP: This function allows the unit to be set in Sleep Mode.
Pressing the Sleep Button ( ) once will set the unit on Low for
6 continuous hours. Pressing the Sleep Button ( ) a second
time will reset the unit to 6 continuous hours. The Oscillation
Button (
) will function when the Fan is in Sleep Mode. Pressing
any other button (Timer, Fan Speed or the Power Button) will
shut off the Sleep Mode.
10.To turn the Fan OFF, press the Power Button (
) and unplug
the unit from the electrical outlet.
CONJUNTO DE LA CABEZA (Figura 4)
1. Coloque el Conjunto del Cabezal sobre el extremo del Extensión
De La Tubería torciendo Conjunto del Cabezal abajo hastaquese
siente en el Extensión De La Tubería.
(Figura 4)
Figura 4
Extensión De La Tubería
Conjunto del Cabezal
ENSAMBLE DEL PIE (Figura 3)
COLOQUE LA BASE EN EL PISO
1. Utilizando un movimiento giratorio, inserte el extremo del tubo de
diámetro grande en el agujero de la Base. El girar el tubería a medida
que se lo empuja asegura que el tubería quede plenamente asentado
en la base.
2.
PARA AJUSTAR LA ALTURA:
a) Afloje la Tuerca De Ajuste De Altura.
b) Eleve o baje el Extensión De La Tubería hasta obtener la
altura deseada.
c) Apriete la Tuerca De Ajuste De Altura.
Base
Extensión De La Tubería
Tuerca De Ajuste De Altura
Figura 3
Conjunto del Cabezal
Figure 7
Inset 7A
Figure 6
Front of
Remote
Back of
Remote
If you lose your remote control, please call Customer Service to
order a replacement at 1-800-233-0268, Monday through Friday,
between the hours of 8:00 a.m. and 5:00 p.m. EST.
Figure 5
S
L
E
E
P