Manual / Bedienungsanleitung Laserworld ShowNET Network Interface Please read this manual carefully prior to product operation! Bitte lesen Sie diese Bedienungsanleitung vor Inbetriebnahme des Produkts! English Deutsch 11/2015
Manual: MicroNet Slim - Network Interface page 2 / 24
Manual: MicroNet Slim - Network Interface Legal notice: Laserworld (Switzerland) AG reserves the right to make modifications to its products, attending to further technical developments. These modifications do not necessarily have to be recorded in each case. This manual and its information have been made with due care. Laserworld AG cannot, however, take any responsibility for errata, bugs, or the resulting damages.
Manual: MicroNet Slim - Network Interface Content: 1. Scope of delivery & details 2. Preliminary warning notices 3. Initial operations, safety instructions 4. Device connections 5. Operation 6.
Manual: MicroNet Slim - Network Interface 1. Scope of delivery & details Please check if all listed parts are included and undamaged. Included in delivery: 1 x Network Interface 1 x Manual 1 x Power Supply Unit 1 x micro-SD Card 2. Preliminary warning notices 1. Please use the network interface only according to these instructions. 2. Do not use the network interface if there are any visible damages. 3. Do not operate the network interface at high humidity, in rain or in dusty environments. 4.
Manual: MicroNet Slim - Network Interface 4.
Manual: MicroNet Slim - Network Interface 5.
Manual: MicroNet Slim - Network Interface DMX settings 3 0-192 Size of the laser projection X axis 193-255 Automatic size change of X axis with increasing speed 0-192 Size of the laser projection Y axis 193-255 Automatic size change of Y axis with increasing speed 0-192 Position of the laser projection X axis 193-255 Automatic position change of X axis with increasing speed 0-192 Position of the laser projection Y axis 193-255 Automatic position change of Y axis with increasing speed 0-192
Manual: MicroNet Slim - Network Interface 5.2 Stand-Alone Mode Dip switch setting switch 1 2 3 4 5 6 7 8 9 10 On (1) / Off (0) 0 0 0 0 1 0 0 0 1 0 In the stand-alone mode, the laser patterns are triggered automatically, even without music. 5.
Manual: MicroNet Slim - Network Interface 5.4.1 DHCP Mode Dip switch setting switch 1 2 3 4 5 6 7 8 9 10 On (1) / Off (0) 0 0 0 0 0 0 0 0 0 0 In this mode, the IP address is provided by a DHCP server. Therefore, a DHCP server has to be available in the network. For example, this could be a cheap 100MBit network router with integrated DHCP server. This option does not work if there is no device in the same network that can distribute and manage network addresses as DHCP. 5.4.
Manual: MicroNet Slim - Network Interface Dip switch setting switch 1 On (1) / Off (0) 2 3 4 5 6 00 - adr1 = 0 10 - adr1 = 1 01 - adr1 = 2 11 - adr1 = 254 0000 - adr2 = 50 1000 - adr2 = 51 0200 - adr2 = 52 1100 - adr2 = 53 0010 - adr2 = 54 1010 - adr2 = 55 0110 - adr2 = 56 1110 - adr2 = 57 0001 - adr2 = 58 1001 - adr2 = 59 0101 - adr2 = 60 1101 - adr2 = 61 0011 - adr2 = 62 1011 - adr2 = 63 0111 - adr2 = 64 1111 - adr2 = 65 7 8 9 10 1 0 0 0 The Windows computer needs to have an IP address
Manual: MicroNet Slim - Network Interface Sender-Receiver configuration for ILDA over LAN, range extender use The sender uses an IP address range between 192.168.2.70 and 192.168.2.85 and transmits the signal to a receiver that has addresses in the range between 192.168.2.50 and 192.168.2.65. The specific IP addresses need to be set with DIP switches. Make sure there are no other devices in the same network that use the same IP addresses.
Manual: MicroNet Slim - Network Interface Final statement Product and package leaving warehouse without faults. Users have to follow the local safety regulations and warnings of this manual. Damages through inappropriate use do not unterlie the sphere of influence of manufacturer or dealer. Therefore no liability or warranty will be taken over. We cannot inform you in case of changes of this manual. If you have any questions, please contact your dealer. For service please contact your dealer or Laserworld.
Manual: MicroNet Slim - Network Interface Inhaltverzeichnis: 1. Lieferumfang & Hinweise 2. Einleitende Warnhinweise 3. Schritte zur Inbetriebnahme, Sicherheitshinweise 4. Anschlüsse / Schnittstellen 5. Bedienung 6.
Manual: MicroNet Slim - Network Interface 1. Lieferumfang & Hinweise Bitte prüfen Sie, ob Sie die Lieferung vollständig erhalten haben und die Ware unbeschädigt ist. Im Lieferumfang enthalten sind: 1 x Netzwerk Interface 1 x Bedienungsanleitung 1 x Netzteil 1 x microSD Karte 2. Einleitende Warnhinweise 1. Das Netzwerk Interface nur gemäß dieser Bedienungsanleitung verwenden. 2. Bitte das Netzwerk Interface nicht verwenden, wenn sichtbare Beschädigungen vorliegen. 3.
Manual: MicroNet Slim - Network Interface 4.
Manual: MicroNet Slim - Network Interface 5.
Manual: MicroNet Slim - Network Interface 5.1 DMX Modus Dip-Schalter-Einstellungen Schalter 1 2 3 4 5 6 7 8 9 10 DMX 1 2 4 8 16 32 64 128 256 muss für den DMX-Modus an (1) sein Für die Laserausgabe muss der DMX-Kanal 1 einen Wert größer als 0 haben (empfohlen 64 192) und auch DMX Kanal 2 muss einen Wert über 0 haben.
Manual: MicroNet Slim - Network Interface DMX Einstellungen Kanal Wert Funktion 10 80-95 Musterprojektion in Magenta 96-111 Musterprojektion in Cyan 112-127 Musterprojektion in Weiß 11 128-255 Regenbogeneffekt 0-31 Default Scannergeschwindigkeit (200 pps) 32-255 Scannergeschwindigkeit manuell (5 - 30kpps) Achtung: Die Scanner dürfen nicht überlastet werden.
Manual: MicroNet Slim - Network Interface 5.4 Netzwerk Modus Wichtig: Wird eine Lasershow-Software verwendet, muss darauf geachtet werden, dass keine Firewall den Datenverkehr zwischen Laser und PC behindert. Sollte die Netzwerkverbindung nicht funktionieren, sollte die Firewall zeitweilig deaktiviert werden. Immer wenn die DIP-Schalter-Einstellungen für den Netzwerk Modus geändert werden (z.B. Änderung der statischen IP-Adresse), muss das Interface (evtl. auch der Laserprojektor) neu gestartet werden.
Manual: MicroNet Slim - Network Interface Dip-Schalter-Einstellungen Schalter 1 On (1) / Off (0) 2 3 4 5 6 00 - adr1 = 0 10 - adr1 = 1 01 - adr1 = 2 11 - adr1 = 254 0000 - adr2 = 50 1000 - adr2 = 51 0200 - adr2 = 52 1100 - adr2 = 53 0010 - adr2 = 54 1010 - adr2 = 55 0110 - adr2 = 56 1110 - adr2 = 57 0001 - adr2 = 58 1001 - adr2 = 59 0101 - adr2 = 60 1101 - adr2 = 61 0011 - adr2 = 62 1011 - adr2 = 63 0111 - adr2 = 64 1111 - adr2 = 65 7 8 9 10 1 0 0 0 Der Windows PC benötigt eine IP-Adresse
Manual: MicroNet Slim - Network Interface Sender-Empfänger Konfiguration für ILDA über LAN, Nutzung als Reichweitenverlängerung Der Sender nutzt den IP Adressbereich zwischen 192.168.2.70 und 192.168.2.85 und überträgt das Signal zum Empfänger, dessen IP Adresse zwischen 192.168.2.50 und 192.168.2.65 liegt. Die jeweilige IP Adresse muss mittels DIP Schalter festgelegt werden. Bitte stellen Sie sicher, dass sich keine anderen Geräte im selben Netzwerk befinden, die die gleichen IP Adressräume nutzen.
Manual: MicroNet Slim - Network Interface Abschließende Erklärung Sowohl Produkt als auch Verpackung sind beim Verlassen der Fabrikation einwandfrei. Der Benutzer des Geräts muss die lokalen Sicherheitsbestimmungen und die Warnhinweise in der Betriebsanleitung beachten. Schäden, die durch unsachgemäße Handhabung entstehen, unterliegen nicht dem Einflussbereich der Herstellers und des Händlers. Somit wird keine Haftung bzw. Gewährleistung übernommen.
Manual: MicroNet Slim - Network Interface page 24 / 24