User Manual
Headset takes too long to pair
Headset will not pair
Gun will not turn on
Headset will not turn on
Plug headset into charger
and LED not turn on
Reload does not work
Gun battery will not charge
Can not hit player
(laser, headset or sighting)
Can not see a red dot in scope
Alt re button not working
Can not get a third party zoom
optical scope sighted in
Gun will not shoot while in game
Sometimes if there are a large number of players turning on headsets at the
same time, or if there are a LOT of wireless bluetooth devices nearby, it could
take up to 3 minutes to pair.
If the headset will not pair after 3 minutes, and the battery is fully charged,
the headset or battery may need replacement.
Make sure the battery is fully charged, if it is charged, the gun or battery may
need repair
Make sure the battery is fully charged, if it is charged, the headset may need
repair
It is possible the charger LED is burned out, but if still does not charge or turn
on, headset may need replacement.
The switch may not be making good contact, take the reload mechanism o
with the two screws, and try pressing the switch with a pen. If it still does not
work, it may need repair.
If the LED on the charger does not turn red during charging, then the battery
or charger may need replacement.
If you can not hit an enemy headset even at close range, then perhaps your
laser needs replacement. If it is one player that is not able to hit your headset
in one or more directions, your headset may need repairs.
The battery in the scope maybe dead.
The button maybe clogged with dirt/oil or need replacement.
If your laser is very o center, then you may not be able to adjust your scope
far enough to get a centered shot. You could try a dierent brand scope to
have more room for adjustment.
If you disconnect headset after a game has started, the gun will lock until
reconnected, to prevent cheating. Gun will however shoot if no headset was
connected at boot up
PROBLEM
TROUBLESHOOTING
SOLUTION
BATTERY SPECIFICATIONS & CAUTIONS
OPTIONAL 6X AA(LR06) 1.5V
• Do not use rechargeable batteries.
• Non-rechargeable batteries are not to be recharged.
•Dierent types of batteries or new and old batteries are
not to be mixed.
• Batteries are to be inserted using correct polarity.
• Remove exhausted batteries as soon as possible and discard properly.
•
Remove all batteries from compartment if rie is not used for
more than seven months.
• The supply terminals are not to be short circuited.
Conforms to product safety standards ASTM F963. Not suitable for
children under 3 years due to small parts. Remove and discard wire ties
before giving this product to children.
PRODUCT COLORS AND STYLES MAY VARY FROM THOSE SHOWN.
This device complies with PART 15 of the FCC Rules. Operation is subject
to the following two conditions. (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
CAUTION: Changes or modications to this unit not expressly approved
by the party responsible for compliance could void the user’s authority to
operate the equipment.
Class 1 Laser Product, EN/IEC 60825 - 2014,
Battle Company, 9100 S. Nicholson Rd, Oak Creek, WI 53154
This product is in conformity with performance standards for laser products under
21CFR 1040, except with respect to those characteristics authorized by Variance
Number FDA-2017-V-0792 eective on September 12, 2017
Model: BRX
• Always maintain awareness of your surrounding.
• Keep a safe distance away from streets, public thoroughfares and power
lines, near high voltage poles, railway tracks, road, or swimming pools.
• Ensure that your phone bracket is secure.
• Contains a long cord and straps which are strangulation hazard for young
children. Keep out of reach of children under 3.
• Avoid intentionally aiming at someone’s eyes or staring down the barrel at
short range for extended periods of time.
To download the most recent product rmware or a more detail
manual, go to our website at www.BattleCompany.com
Warning: Changes or modifications to this unit not expressly approved by the party
responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may
cause undesired operation.
FCC Statement: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
Warning: