Installation Manual

Using 3/16" screws, attach shoe to vehicle.
2. Slip the RadioRay® into the shoe. Verify that the spring lock
secures the RadioRay® into the shoe. An optional magnetic
mounting shoe is available (see accessory sheet).
PROGRAMMABLE REMOTE INSTRUCTIONS
The Golight® RadioRay® is controlled with a programmable remote
with 6561 different channels. This feature allows you the freedom to
change the channel selection, and the receiver relearns the new
selection.
PROGRAMMING THE TRANSMITTER.
This light has been pre-programmed at the factory, and it is not
necessary to re-program the transmitter, unless you experience
outside interference.
1. IMPORTANT: Disconnect power by removing fuse or
disconnecting vehicle battery.
2. Remove battery cover from remote control.
3. Set the 7 dip switches to a selection of your choice. There are 3
positions on each; positive, negative and neutral. Use a small
screwdriver and select a position for each dip switch. *Please note
that the orientation of the +/- switch positions may vary among
different models of wireless remote controls.
4. Insert both Duracell MN21 batteries with the +/– in the same
direction. Be sure batteries have adequate charge.
5. Replace battery cover.
a. Depress the on/off button and hold it down. Red LED will light.
b. While holding the on/off button down, reinstall the power
(plug the cigarette lighter plug in).
c. Keep your finger on the on/off button for 5-6 seconds, and then
release. The light should now be programmed.
The Golight® RadioRay® is a Portable Searchlight designed to be
permanently or temporarily attached to a vehicle for your specific use.
The 2-Speed Searchlight with Directional Flexibility is controlled by a
wireless remote, which gives the operator a full 370° horizontal
rotation and a 135° vertical tilt with fingertip control. The RadioRay®
provides superior light penetration with Cr5 PentaBeam™ technology.
The RadioRay® Includes:
• RadioRay® Searchlight
(Free-standing light with suction mounting.)
• Remote Control (Must be kept clean and dry.)
• 2 Duracell MN21 Batteries
• Rain Coat for Remote
• Permanent Mounting Shoe
(Press spring lock to release and remove light.)
• Permanent Mounting Gasket
• Rockguard
• An Optional Magnetic Shoe (See Accessory Sheet)
MOUNTING INSTRUCTIONS
Temporary:
1. Always clean mounting surface with a clean cloth.
2. Remove light from permanent mount shoe by depressing spring
loaded lock and sliding light out.
3. Place suction base on clean, dry surface and move side lever into
the locked position.
WARNING: Check the suction cup frequently to ensure that suction
strength is maintained. Temperature variations, rough terrain, grease
and dirt affect the length of time that the suction cup will remain in
place.
Permanent:
1. On clean, dry surface, place gasket and shoe in desired location.
OPERATION OF GOLIGHT® RADIORAY®
1. Place your RadioRay® into the mounting shoe or attach to the
outside of your vehicle (see mounting instructions).
2. Plug your RadioRay® into your vehicle's cigarette lighter outlet or
12 Volt direct battery hookup.
3. Using the remote control, turn on the light by depressing the
on/off button.
4. With the 4-way arrows on the remote control, rotate your light
to the desired location. Depending upon conditions, the
wireless remote may be used up to 100 feet from the RadioRay®.
5. The speed of the light rotation can be controlled by depressing
the +/– button one time and by depressing it again to
restore the original speed.
6. Unplug and remove light from vehicle. Store the light and remote
control in optional carrying case when not in use to extend the life
of your RadioRay®.
7. The spotlight should not be turned on when the snap on lens
cover (rockguard) is attached.
WARNING: Unplug unit when not in use.
BULB REPLACEMENT
The Golight® RadioRay® utilizes a Philips® H-9 bulb, which may be
purchased through Golight, Inc. — 308.278.3131 or 800.557.0098.
www.magnalight.com
1-800-369-6671
903-498-3363
[e-mail]