User Manual
ground and the back 2 being hot.
NOTE: Front of socket is flat.
6. Attach power supply connections to the socket, making sure to
wire in accordance with both A.B.Y.C. Standard E-9 and U.S. Coast
Guard Safety Standards for Boat Electrical Systems (33 CFR 183).**
The supply to this socket for use with the RadioRay® must be
protected with a 10 Amp fuse or circuit breaker (12 Volt DC).
7. Mount the base and socket in accordance with the template.
INSTALLATION: EXISTING PERKO MOUNT SOCKET
Carefully engage stanchion into base socket. As it slides into socket,
make sure the alignment screw at rear of stanchion slides into notch
at rear of socket. Push stanchion down until it engages with electrical
connector at bottom of socket. Lock unit in place by sliding lock collar
into the top of the socket and rotate clockwise. Check to make sure
stanchion is secure in the socket.
The Golight® RadioRay® Model 2100/2110 is ready for immediate use.
TROUBLE SHOOTING YOUR RADIORAY® MODEL 2100/2110
If the power receptacle is wired correctly and the light still will not
activate with the remote, the boat wire may not be the recommended
gauge. Golight, Inc. recommends a minimum of 14 guage wire; 16
gauge may or may not be sufficient depending on total length of wire.
PROGRAMMABLE REMOTE INSTRUCTIONS
The Golight® RadioRay® is controlled with a programmable remote
with 6561 different channels. This feature allows you the freedom to
change the channel selection, and the receiver relearns the new
selection.
PROGRAMMING THE TRANSMITTER.
This light has been pre-programmed at the factory, and it is not
necessary to re-program the transmitter, unless you experience
outside interference.
The Golight® RadioRay® Model 2100/2110 is designed to be used with
the included Perko base socket or an accommodating base socket.
The 2-Speed Searchlight with Directional Flexibility is controlled by a
wireless remote, which gives the operator a full 370° horizontal
rotation and a 135° vertical tilt with fingertip control. The RadioRay®
provides superior light penetration with Cr5 PentaBeam™ technology.
The RadioRay® Includes:
• RadioRay® Searchlight
—Mounted on 12" Stanchion with 12 Volt DC Navigation Lights
• Programmable Wireless Remote (must be kept clean and dry)
• 2 Duracell MN21 or 2 Energizer 23A Batteries
• Raincoat for Remote
• Perko 1047-P00-DP Base Socket
• Lined Nylon Storage Bag
INSTALLATION: NON-EXISTING PERKO MOUNT SOCKET
(See Template on Back of Warranty Card)
1. Locate an appropriate horizontal location on deck or
superstructure for installation of socket.
2. Draw a 6" long reference line through the center of the selected
mounting location, parallel with the centerline of the boat.
3. Cut out the mounting template. Place it on the mounting surface
such that the reference line (step 2) is directly underneath the
reference line on the template.
4. Drill pilot holes through the template to accommodate #8 oval
head mounting screws (not included).
5. Open a 1.25" diameter hole according to template to
accommodate socket.
IMPORTANT: This light has been designed to operate in a 2-pin
socket, regardless of hot/ground orientation. ✱ Existing 3-pin sockets
will require modification. So 1 hot and 1 ground lead to the rear 2
pins. 3-pin sockets are originally wired with the front pin being
1. IMPORTANT: Remove RadioRay® from base socket receptacle.
2. Remove battery cover from remote control.
3. Set the 7 dip switches to a selection of your choice. There are 3
positions on each; positive, negative and neutral. Use a small
screwdriver and select a position for each dip switch. Please note
that the orientation of the +/– switch positions may vary among
different models of wireless remote controls.
4. Insert both MN21 Duracell or Energizer 23A batteries with the
+/– in the same direction. Be sure batteries have adequate charge.
5. Replace battery cover.
a. Depress the on/off button and hold it down. Red LED will light.
b. While holding the on/off button down, reinstall the power
(replace RadioRay® into base socket).
c. Keep your finger on the on/off button for a few seconds and let
off. The process is finished and the light should now be
programmed.
OPERATION OF GOLIGHT® RADIORAY®
1. Using the remote control, turn on the light by depressing the
on/off button.
2. With the 4-way arrows on the remote control, rotate your light
to the desired location. Depending upon conditions, the
wireless remote may be used up to 100 feet from the RadioRay®.
3. The speed of the light rotation can be controlled by depressing
the +/– button one time and by depressing it again to
restore the original speed.
BULB REPLACEMENT
The Golight® RadioRay® utilizes a Philips® H-9 bulb, which may be
purchased through Golight, Inc. — 308.278.3131 or 800.557.0098.
**
American Boat & Yacht Council, 3069 Solomon's Island RD, Edgewater, MD 21037
www.magnalight.com
1-800-369-6671