Datasheet

ManualsBrandsLAPPKABEL ManualsIndustrial Data CablesUNITRONIC BUS Yv L2/FIP Profibus Cable Black

U.I. Lapp

GmbH

DATA SHEET

UNITRONIC BUS PB Yv 1 x 2 x 0,64

DB2170223

valid from: 29.11.2011

Originator: RAWE/PDC

approved: HAPF/PDC

Document: DB2170223 page 1 of 2

PD 0019/2.2_11.10DE

Application

Fieldbus cable for the Siemens field network SIMATIC NET (acc. to DIN 19245 part 3 and EN 50170), for fieldbus system FIP

(Factory Instrumentation Protocol) as well as for high performance data networks with 150 Ohms nominal impedance. The

cable is designed for the system-defined transmission rates of 1.5 Mbit/s, 2.5 Mbit/s and 12 Mbit/s, the transmission

characteristics are conform to the system and guarantee a high operating security during data transmission.

Due to it´s double screening it is suitable for installation in electromagnetically demanding areas. The cable is intended for

permanent installation inside and outside as well as for underground burial. The outer sheath is unaffected by atmospheric

UV-radiation at above-ground installation.

Design

Conductor bare copper wire, nom. 0.64 mm Ø

Insulation skin-foam-skin PE, alternatively foam-skin, core Ø nom. 2.55 mm

Core identification code cores red similar to RAL 3000 and green similar to RAL 6018

Stranding 2 cores together with 2 fillers

Wrapping 1 layer plastic foil

Screening plastic-laminated aluminium foil, side with metal outwards, braid of tinned

copper wires, coverage nom. 85%

Outer sheath PVC, lead free, shore hardness A 77 ± 3, black similar to RAL 9005,

wall thickness nom. 1.8 mm, outer diameter: ca. 9.4 mm

Electrical properties at 20° C

Resistance (loop) max. 110 Ω/km

Insulation resistance min. 5 GΩxkm

Mutual capacitance ca. 28 nF/km

(at 800 Hz)

Inductance ca. 0.83 mH/km

(at 800 Hz)

Characteristic impedance 9.6 kHz: 270 Ω ± 27

38.4 kHz: 185 Ω ± 18.5

3 bis 20 Mhz: 150 Ω ± 15

Line attenuation 9.6 kHz: max. 0.25 dB/100 m

38.4 kHz: max. 0.4 dB/100 m

200 kHz: max. 0.9 dB/100 m

4 MHz: max. 2.2 dB/100 m

16 MHz: max. 4.2 dB/10 0m

Velocity of propagation nom. 81%

Transfer impedance up to 20 MHz max. 10 mΩ/m

Operating peak voltage 225 V (not for power purposes)

Test voltage U

eff.

core/core und

core/screen

1500 V

Summary of content (2 pages)

PAGE 1
U.I. Lapp GmbH DATA SHEET UNITRONIC BUS PB Yv 1 x 2 x 0,64 DB2170223 valid from: 29.11.2011 Application Fieldbus cable for the Siemens field network SIMATIC NET (acc. to DIN 19245 part 3 and EN 50170), for fieldbus system FIP (Factory Instrumentation Protocol) as well as for high performance data networks with 150 Ohms nominal impedance. The cable is designed for the system-defined transmission rates of 1.5 Mbit/s, 2.
PAGE 2
U.I. Lapp GmbH DATA SHEET UNITRONIC BUS PB Yv 1 x 2 x 0,64 DB2170223 valid from: 29.11.2011 Mechanical and thermal properties Minimum bending radius static: 10 x cable Ø Permissible temperature range static: -40˚ C up to +80˚ C General requirements Dangerous and forbidden substances acc. to RoHS directive (2002/95/EG) are not allowed to the manufacturing. Originator: RAWE/PDC approved: HAPF/PDC All rights reserved acc. to DIN ISO 16016. PD 0019/2.2_11.