Data Sheet

ManualsBrandsLAPP ManualsBus CablesBus cable UNITRONIC® BUS 1 x 2 x 0.32 mm² V

U.I. Lapp

GmbH

DATA SHEET

UNITRONIC BUS PB FD P 1 x 2 x 0,64

DB 2170222

valid from: 14.09.2012

Originator: KASC / PDC

Approved: HAPF / PDC

Document: DB2170222EN Page 1 of 2

PD 0019/2.2_11.10EN

Application

Highly flexible data cable for the SIEMENS field-net SINEC L2 DP (acc. to DIN 19245, part 3 and EN 50 170) for fieldbus

system FIP (Factory Instrumentation Protocol) as well as for high performance data networks with 150 Ω nominal

impedance. The cable is designed for the system-defined transmission rates of 1.5 MBit/s, 2.5 MBit/s and 12 MBit/s, the

transmission characteristics are conform to the system and guarantee a high operating security during the data

transmission. The used materials are halogen free.

The cable is intended for high flexible application in power chains, on permanently moving machines and linear robots. Due

to its double screening it is suitable for installation in electromagnetically demanding areas. The PUR-sheath is very resistant

against mineral oils and abrasion.

This cable is suitable for torsion application in wind turbines (WTG). The torsional load is limited to applications, as they

typically occur in the loop of a wind turbine.

Design

Conductor

bare copper, nom. 0

.25 mm

(24 AWG)

Insulation

Skin-Foam-Skin PE, core

∅

nom. 2.55 mm

Core identification code

cores red and green

Stranding

2 cores together with 2 fillers

Wrapping

1 layer non woven tape

Screening

plastic

laminated aluminium foil, side with metal outw

ards, braid of tinned

copper wires, coverage nom. 85%

Outer sheath

PU flame retardant and halogen free, violet similar to RAL 4001,

wall thickness nom. 1.0 mm, outer diameter: max. 8.0 mm

Electrical properties at 20 °C

Resistance (loop)

max. 145

Ω/

Insulation resistance

min. 5 G

Ωxkm

Mutual capacitance

A/A: ca. 32 nF/km

A/S: ca. 49 nF/km

(at 800 Hz)

Inductance

800 Hz: ca. 0.82 mH/km

Characteristic impedance

9,6 kHz: 270

Ω

± 27

38,4 kHz: 185 Ω ± 18

3 bis 20 Mhz: 150 Ω ± 15

Line a

ttenuation

9,6 kHz: max. 0.3 dB/100 m

38,4 kHz: max. 0.4 dB/100 m

4 MHz: max. 2.5 dB/100 m

16 MHz: max. 4.9 dB/100 m

Velocity of propagation

nom. 0,81c

Transfer impedance up to 20 MHz

max. 10 m

Ω/m

Operating peak voltage

220 V (not for power purp

oses)

Test voltage U

eff.

core/core und

core/screen

1500 V

Summary of content (2 pages)

PAGE 1
U.I. Lapp GmbH DATA SHEET UNITRONIC BUS PB FD P 1 x 2 x 0,64 DB 2170222 valid from: 14.09.2012 Application Highly flexible data cable for the SIEMENS field-net SINEC L2 DP (acc. to DIN 19245, part 3 and EN 50 170) for fieldbus system FIP (Factory Instrumentation Protocol) as well as for high performance data networks with 150 Ω nominal impedance. The cable is designed for the system-defined transmission rates of 1.5 MBit/s, 2.
PAGE 2
U.I. Lapp GmbH DATA SHEET UNITRONIC BUS PB FD P 1 x 2 x 0,64 DB 2170222 valid from: 14.09.2012 Mechanical and thermal properties Min. bending radius Permissible temperature range 65 mm moved: -30˚ C up to +70˚ C Torsion movement in WTG TW-0 (5000 cycles at ≥ +5°C) TW-2 (2000 cycles at ≥ -40°C) ± 150 °/m at 1 revolution per minute Flame propagation flame retardant acc. to IEC 60332-1-2 Halogen free acc. to VDE 0472-815 EC-Directives Dangerous and forbidden substances acc.