Congratulations on your purchase of a Lanzar Vibe amplifier. You have purchased a quality product designed and engineered to give you many years of uncompromised musical service. Vibe amplifiers are designed with the latest technology available, incorporating a DC to DC Switching Power Supply, which provides headroom for even the most demanding peaks and dynamic ranges found on modern CD’s and recordings.
F EATURES C ONTROLS AND VIBE232/242/252/262/292 Level High Pass Mode Low Pass Bass Boost R Remote PWR PROT Min Max 40Hz 3kHz Full High Low On 40Hz 350Hz Off L Line Out Line Input I NPUT L EVEL C ONTROLS P OWER Enables the matching of input levels to the output levels from the head unit (or other signal source). Provide instant information on status of amplifier, including short-circuit and thermal overload alerts.
F EATURES C ONTROLS AND VIBE412/422/432 High Pass High Pass Remote Power CH2 CH4 Protect Level CH1 Line out Line input Min Max Bass Boost Off I NPUT L EVEL C ONTROLS Enables the matching of input levels to the output levels from the head unit (or other signal source). B ASS B OOST C ONTROL Increases sound level in lower frequencies by 18dB.
F EATURES AND C ONTROLS VIBE532 CHANNEL 3+4 CHANNEL 1+2 Level Mode High Pass CH4 Level Mode High Pass Bass Boost CHANNEL 5+6 Low Mode Level Pass CH2 CH6 Min Max Full Full On Low Off 40Hz 500HzPass Min Max Band pass High 40Hz 4kHz pass Input Mode High 40Hz 4kHz pass Full Min Max PROT PWR CH1 Low Input Low Input 40Hz 4kHz CH3 High Pass 40Hz 500Hz Band Low Pass Pass Ch4 Ch6 Low Input Remote CH5 I NPUT L EVEL C ONTROLS ˄ALL CHANNELS˅ R EMOTE C ONTRROL Enables the matching of in
S PECIFICATIONS 2 channel amplifie r 2 channel amplifie r Vibe262 2 channel amplifie r Vibe232 RMS at 4 Ohms 2x300W 2x500W 2x750W 2x1050W MAX at 4 Ohms 2x600W 2x1000W 2x1500W 1x2100W At 4 Ohms Bridged 1x1200W 1x2000W 1x3000W 1x4200W RMS at 2 Ohms 2x500W 2x840W 2x1200W 2x1750W Min. Speaker Impedance 2 Ohm 2 Ohm 2 Ohm 2 Ohm T.H.D 0.05% 0.05% 0.05% 0.
channel Vibe292 2amplifie r channel Vibe412 4amplifie r channel Vibe422 4amplifie r Vibe432 2x1250W 4x125W 4x250W 4x500W 4x250W+1x600W 2x2500W 4x250W 4x500W 4x1000W 4x500W+1x1200W 1x5000W 2x500W 2x1000W 2x2000W 2x1000W+1x1200W 2x2100W 4x200W 4x400W 4x850W 4x575W+1x875W 2 Ohm 2 Ohm 2 Ohm 2 Ohm 2 Ohm 0.05% 0.05% 0.05% 0.05% 0.
I NSTALLATION PRECAUTIONS 1. Find a suitable location in the vehicle to mount the amplifier. 2. Make sure there is sufficient air flow around the intended mounting location. 3. Bolt the amplifier to the mouning surface. 4. Connect the power ground terminal to the nearet point on the chassis of the car. Keep this ground wire less than one meter (39”) in length. Use 8 gauge wire. 5. Connect the remote terminal to the remote output of the head unit using 14 gauge wire. 6.
S VIBE232/242/252/262/292 Y ST EM W IRING 2 CHANNEL STEREO CONFIGURATION Level High Pass Mode Bass Boost Low Pass Remote PWR R PROT Min Max 40Hz 3kHz Full High Low On 40Hz 350Hz Off FRONT L Line Out Line Input LEVEL TO OUTPUT FROM MIN HEAD UNIT POWER MAX to REMOTE SUBWOOFER LEVEL CONTROL SPEAKERS REAR + FUSES VIBE232/242 ONLY BATTERY + TO REMOTE OUTPUT FROM HEAD UNIT + 12V REM GND + RIGHT BRIDGED MODE LEFT - + - SPEAKER IMPEDANCE TO LEFT SPEAKER RIGHT + SPEAKER
S Y ST EM W IRING 2 CHANNEL BRIDGED MODE CONFIGURATION Level High Pass VIBE232/242/252/262/292 Mode Low Pass Bass Boost Remote PWR R PROT Min Max 40Hz 3kHz Full High Low On 40Hz 350Hz Off FRONT L Line Out Line Input LEVEL TO OUTPUT FROM HEAD UNIT MIN POWER MAX to REMOTE SUBWOOFER LEVEL CONTROL SPEAKERS REAR + FUSES + 12V VIBE232/242 ONLY TO BATTERY TO REMOTE + OUTPUT FROM HEAD UNIT 8 — V I B E O W N E R ’ S M A N U A L REM GND + RIGHT BRIDGED MODE LEFT - -
S VIBE232/242/252/262/292 Y ST EM W IRING 2 CHANNEL TRI-MODE CONFIGURATION Level High Pass Bass Boost Low Pass High Mode Remote PWR R PROT Min Max 40Hz 3kHz Full High Low On 40Hz 350Hz Off FRONT L Line Out Line Input LEVEL TO MIN OUTPUT FROM HEAD UNIT POWER MAX to REMOTE SUBWOOFER LEVEL CONTROL SPEAKERS REAR + FUSES + 12V REM GND VIBE232/242 ONLY TO BATTERY TO REMOTE FROM HEAD - - + + OUTPUT UNIT + RIGHT BRIDGED MODE LEFT LEFT SPEAKER + + SPEAKER IMPEDANCE 4-8 OH
S W Y ST EM IRING TRIAMP SYSTEM USING THREE 2 CHANNEL AMPLIFIERS VIBE232/242/252/262/292 MASTER AMP FRONT (WOOFERS) Level High Pass Mode Low Pass Bass Boost MASTER AMP RAER Remote POWER SPEAKERS PWR R PROT Min Max 40Hz 3kHz Full High Low On Off 40Hz 350Hz L + Line Out FUSES Line Input + 12V REM GND VIBE232/242 ONLY LEVEL switch in TO OUTRUT FROM HEAD UNIT Low Pass Position Full High Low MIN MAX to REMOTE SUBWOOFER LEVEL CONTROL TO BATTERY High Pass Mode Low Pass Ba
S VIBE412/422/432 W Y ST EM IRING 4 CHANNEL STEREO CONFIGURATION Remote High Pass PWR PROT Level CH1 Line out Line Input Min Max Bass Boost Mode 40Hz 3kHz 40Hz 3kHz Low pass Low pass Full Full 40Hz 350Hz40Hz 350Hz Low Low pass High High pass pass pass Off On Bass Boost Off On FRONT Level Min Max Line Input Line Out CH3 Y ADAPTOR Y ADAPTOR TO Mode CH4 eniL tupnI High Pass CH2 LEVEL OUTPUT FROM HEAD UNIT MIN to REMOTE SUBWOOFER LEVEL CONTROL MAX REAR + CH1 12V REM GND
S W Y ST EM IRING VIBE412/422/432 4 CHANNEL BRIDGED MODE CONFIGURATION Remote High Pass High Pass PWR CH2 CH4 PROT Level CH1 Line out Min Max Line Input Bass Boost Off On Mode 40Hz 3kHz 40Hz 3kHz Low pass Low pass Mode Full Full 40Hz 350Hz40Hz 350Hz Low Low pass High High pass pass pass Y ADAPTOR Off FRONT Level Bass Boost Min Max On Line Input Line Out CH3 RIGHT OUTPUT FROM HEAD UNIT To LEVEL LEFT OUTRUT FROM HEAD UNIT TO MIN MAX to REMOTE SUBWOOFER LEVEL CONTROL REAR
S VIBE412/422/432 W Y ST EM IRING 4 CHANNEL TRI-MODE CONFIGURATION Remote High Pass PWR PROT Level CH1 Line out Line Input Min Max Bass Boost Mode 40Hz 3kHz 40Hz 3kHz Low pass Low pass Full Full 40Hz 350Hz40Hz 350Hz Low Low pass High High pass pass pass Off On Off FRONT Level Bass Boost Min Max On Line Input Line Out CH3 Y ADAPTOR Y ADAPTOR TO Mode CH4 eniL tupnI High Pass CH2 LEVEL OUTPUT FROM HEAD UNIT MIN to REMOTE SUBWOOFER LEVEL CONTROL MAX REAR + CH1 12V REM GN
S W Y ST EM IRING VIBE532 5 CHANNEL STEREO CONFIGURATION Input Mode Swith in Ch 4 position CHANNEL 3+4 CHANNEL 1+2 Level Mode High Pass CH4 Level Mode High Pass CHANNEL 5+6 Low Mode Level Pass Bass Boost Ch4 CH2 Ch6 CH6 Full On Low Off 40Hz 500HzPass Min Max Band pass High 40Hz 4kHz pass Input Mode Min Max Full High 40Hz 4kHz pass Full FRONT Min Max PROT PWR CH1 Low Input Low Input 40Hz 4kHz CH3 High Pass 40Hz 500Hz Band Low Pass Pass Y ADAPTOR Ch4 Ch6 Low Input Remote CH
S VIBE532 W Y ST EM IRING 5 CHANNEL BRIDGED MODE CONFIGURATION Input Mode Swith in Ch 6 position CHANNEL 3+4 CHANNEL 1+2 Level Mode High Pass CH4 Level Mode High Pass CHANNEL 5+6 Low Mode Level Pass Bass Boost Ch4 Ch6 CH2 CH6 Full On Low Off 40Hz 500HzPass Min Max Band pass High 40Hz 4kHz pass Input Mode Min Max Full High 40Hz 4kHz pass Full FRONT Min Max PROT PWR CH1 Low Input Low Input 40Hz 4kHz CH3 High Pass Y ADAPTOR Y ADAPTOR LEFT INPUT Ch4 40Hz 500Hz Band Low Pass Pass
S W Y ST EM IRING VIBE532 5 CHANNEL TRI-MODE CONFIGURATION CHANNEL 3+4 CHANNEL 1+2 Level Mode High Pass CH4 Level Mode High Pass CHANNEL 5+6 Low Mode Level Pass Bass Boost CH2 CH6 Full On Low Off 40Hz 500HzPass Min Max Band pass High 40Hz 4kHz pass Input Mode Min Max Full High 40Hz 4kHz pass Full FRONT Min Max PROT PWR CH1 Low Input Low Input 40Hz 500Hz 40Hz 4kHz MIN OUTPUT FROM Ch6 Low Input Remote LEVEL Y ADAPTOR TO Ch4 Band Low Pass Pass CH3 High Pass HEAD UNIT CH5
TROUBLESHOOTING AMPLIFIER WILL NOT POWER UP . Check for good ground connection. Check that remote DC terminal has at least 3v DC. Check that there is battery power on the + terminal. Check all fuses. Check that Protection LED is not lit. If it is lit, shut off amplifier briefly and then repower it. H IGH HISS OR ENGINE NOISE (ALTERNATOR WHINE) IN SPEAKERS. Disconnect all RCA inputs to the amplifier(s) - if hiss/noise disappears, then plug in the component driving the amplifier and unplug its inputs.
