TM EDS-MD User Guide EDS-MD4 EDS-MD8 EDS-MD16 Part Number 900-591 Revision D November 2011
Copyright & Trademark © 2011 Lantronix. All rights reserved. No part of the contents of this book may be transmitted or reproduced in any form or by any means without the written permission of Lantronix. Printed in the United States of America. Ethernet is a trademark of XEROX Corporation. Windows is a trademark of Microsoft Corporation. Linux is a registered trademark of Linus Torvalds. Warranty For details on the Lantronix warranty replacement policy, please go to our web site at www.lantronix.
Table of Contents Copyright & Trademark ______________________________________________________ 2 Warranty _________________________________________________________________ 2 Contacts _________________________________________________________________ 2 Disclaimer ________________________________________________________________ 2 Revision History ___________________________________________________________ 2 List of Figures ____________________________________________________________ 12 List of Tables _________
3: Installation of EDS-MD4/8/16 Device Servers 23 Package Contents _________________________________________________________ 23 User-Supplied Items _______________________________________________________ 23 Identifying Hardware Components ____________________________________________ 23 Serial Ports ___________________________________________________________ 24 Ethernet Port _________________________________________________________ 24 LEDs ________________________________________________________________ 24
To Configure Tunnel Packing Mode Settings _________________________________ 38 Using Web Manager ________________________________________________ 38 Using the CLI ______________________________________________________ 39 Using XML ________________________________________________________ 39 Accept Mode __________________________________________________________ 39 To Configure Tunnel Accept Mode Settings __________________________________ 40 Using Web Manager ________________________________________________ 4
8: Terminal and Host Settings 49 Terminal Settings _________________________________________________________ 49 To Configure the Terminal Network Connection _______________________________ 50 Using Web Manager ________________________________________________ 50 Using the CLI ______________________________________________________ 50 Using XML ________________________________________________________ 50 To Configure the Terminal Line Connection __________________________________ 50 Using Web Manager ________
To Configure RSS Settings ______________________________________________ 56 Using Web Manager ________________________________________________ 56 Using the CLI ______________________________________________________ 57 Using XML ________________________________________________________ 57 Real Time Clock (RTC) Settings ______________________________________________ 57 To Configure RTC Settings ______________________________________________ 57 Using Web Manager ________________________________________________
Using XML ________________________________________________________ 65 File Modification _______________________________________________________ 66 File Transfer __________________________________________________________ 66 To Transfer or Modify Filesystem Files ______________________________________ 67 Using Web Manager ________________________________________________ 67 Using the CLI ______________________________________________________ 67 Using XML ________________________________________________________
Using the CLI ______________________________________________________ 71 Using XML ________________________________________________________ 71 Traceroute ___________________________________________________________ 71 To Perform a Traceroute ________________________________________________ 71 Using Web Manager ________________________________________________ 71 Using the CLI ______________________________________________________ 71 Using XML ________________________________________________________ 71 Log ____
Using the CLI ______________________________________________________ 76 Using XML ________________________________________________________ 76 Telnet Settings ________________________________________________________ 77 To Configure Telnet Settings _____________________________________________ 77 Using Web Manager ________________________________________________ 77 Using the CLI ______________________________________________________ 77 Using XML ________________________________________________________ 77 SSH
Using Web Manager ________________________________________________ 82 Using the CLI ______________________________________________________ 82 Using XML ________________________________________________________ 83 Virtual IP (VIP) Counters ____________________________________________________ 83 To View VIP Counters __________________________________________________ 83 Using Web Manager ________________________________________________ 83 Using the CLI ______________________________________________________ 83 U
List of Figures Figure 2-1 EDS-MD Product Label ___________________________________________________ 22 Figure 3-1 Front View of the EDS-MD16 ______________________________________________ 24 Figure 3-2 Back View of the EDS-MD4, EDS-MD8 and EDS-MD16 _________________________ 24 Figure 5-1 Components of the Web Manager Page ______________________________________ 32 Figure 17-2 Windows Scientific Calculator _____________________________________________ 88 Figure 17-3 Hexadecimal Values in the Scientific Calcul
List of Tables Table 3-3 System LEDs on the Top of EDS-MD ________________________________________ 24 Table 3-4 Serial Indicator LEDs on the Top of EDS-MD __________________________________ 25 Table 3-5 RJ45 LEDs on the Back Panel (Ethernet Indicators).
Table 11-8 Query Port Settings _____________________________________________________ 69 Table 11-9 Ping Settings __________________________________________________________ 71 Table 11-10 Traceroute Settings ____________________________________________________ 71 Table 11-11 Log Settings __________________________________________________________ 72 Table 11-12 System Settings _______________________________________________________ 74 Table 12-1 Email Configuration ____________________________________________
1: Using This Guide Purpose and Audience This guide provides the information needed to configure, use, and update the EDS-MD4, EDSMD8 and EDS-MD16. It is intended for system integrators who are installing this product into their designs. Note: EDS-MD device servers (which include models EDS-MD4, EDS-MD8 and EDSMD16) are commonly referred to as either EDS-MD4/8/16 or as EDS-MD when mentioned within a description equally applicable to any of the three models.
1: Using This Guide Safety Information This section describes the safety precautions that should be followed when installing and operating the EDS-MD. Warning: This equipment is not suitable for use in the presence of a flammable anaesthetic mixture including air, oxygen or nitrous oxide. Cover Warning: Note: Do not remove the cover of the EDS-MD. There are no user-serviceable parts inside. Opening or removing the cover may expose you to dangerous voltage that could cause fire or electric shock.
1: Using This Guide Battery A Lithium battery cell inside the unit maintains the unit's date and time when the device is powered off. Do not attempt to replace it. The battery is serviceable only by Lantronix. Caution: Attention: DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY REPLACED. REPLACE ONLY WITH THE SAME OR EQUIVALENT TYPE RECOMMENDED BY THE MANUFACTURER. DISPOSE OF USED BATTERIES ACCORDING TO THE MANUFACTURER'S INSTRUCTIONS.
1: Using This Guide Equipment Classifications Classification according to the type of protection against electric shock: Class I Equipment Classification according to the degree of protection against electric shock: No Applied Parts Classification according to the degree of protection against ingress of water: IP20 Classification according to the mode of operation: Continuous Operation Environmental Conditions for Transportation and Storage An ambient temperature range of -30°C to +80°C
1: Using This Guide Additional Documentation Visit the Lantronix Web site at www.lantronix.com/support/documentation for the latest documentation and the following additional documentation. Document Description EDS-MD Command Reference Instructions for accessing Command Mode (the command line interface) using a Telnet connection, SSH connection or through the serial port. Detailed information about the commands. Also provides details for XML configuration and status.
2: Introduction The EDS-MD4, EDS-MD8 and EDS-MD16 Ethernet Device Servers are complete networkenabling solutions. This device server allows system integrators and administrators to go to market quickly and easily with Ethernet networking and web server capabilities. EDS-MD models are available in 4, 8 and 16 port configurations.
2: Introduction Troubleshooting Capabilities The EDS-MD4/8/16 offers a comprehensive diagnostic toolset that lets you troubleshoot problems quickly and easily. Available from the CLI or Web Manager, the diagnostic tools let you: View memory and IP socket information. Perform ping and traceroute operations. Conduct forward or reverse DNS lookup operations. View all processes currently running on the EDS-MD, including CPU utilization. View system log messages.
2: Introduction Port Numbers Every TCP connection and every UDP datagram is defined by a destination and source IP address, and a destination and source port number. For example, a Telnet server commonly uses TCP port number 23.
3: Installation of EDS-MD4/8/16 Device Servers This chapter describes how to install the EDS-MD4, EDS-MD8 and EDS-MD16 device servers.
3: Installation of EDS-MD4/8/16 Device Servers Figure 3-1 Front View of the EDS-MD16 Note: EDS-MD4 has 4 RJ45 Serial Ports and EDS-MD8 has 8 RJ45 Serial Ports. Figure 3-2 Back View of the EDS-MD4, EDS-MD8 and EDS-MD16 USB Port RJ45 Ethernet Ports Note: Ethernet ports 2 and 3 will become operational with a future firmware update. Power Connector Serial Ports In the front of the device, the EDS-MD4 has 4 serial ports, the EDS-MD8 has 8 serial ports, and the EDS-MD16 has 16 serial ports.
3: Installation of EDS-MD4/8/16 Device Servers Table 3-4 Serial Indicator LEDs on the Top of EDS-MD LED Description Green Indicates there is a tunnel connection to or from the EDS-MD. Red Not supported. Off There is no tunnel connection on the serial line. Note: Number of Serial LEDs correspond with the EDS-MD model number. For instance, EDS-MD4 has 4 LEDs, EDS-MD8 has 8 LEDs, and EDS-MD16 has 16 LEDs. Table 3-5 RJ45 LEDs on the Back Panel (Ethernet Indicators).
3: Installation of EDS-MD4/8/16 Device Servers Technical Specification Category Description NETWORK INTERFACE Ethernet Ports 3 RJ45 10Base-T/100Base-TX/1000Base-T Ethernet ports Auto sensing Automatic MDI/MDI-X crossover Full duplex IEEE 802.3x flow control Half-duplex back pressure flow control Left LED Indicator See Table 3-5. Right LED Indicator See Table 3-5. Isolation from internal circuit 1.5 KVAC Isolation from adjacent port 1.5 KVAC USB INTERFACE USB Ports 2 of USB-A Host, USB 2.
3: Installation of EDS-MD4/8/16 Device Servers Category (continued) Description PHYSICALS Dimensions L x W x H = 8.25 x 7.5 x 2.4 in. (21 x 19 x 6 cm) Weight 16-port = 2.0 lbs (0.9 Kg) 8-port = 1.8 lbs (0.82 Kg) 4-port = 1.75 lbs (0.
4: Using DeviceInstaller This chapter covers the steps for locating a EDS-MD4/8/16 unit and viewing its properties and device details. DeviceInstaller is a free utility program provided by Lantronix that discovers, configures, upgrades and manages Lantronix Device Servers. Notes: For instructions on using DeviceInstaller to configure the IP address and related settings or for more advanced features, see the DeviceInstaller Online Help. Auto IP generates a random IP address in the range of 169.254.0.
4: Using DeviceInstaller Current Settings (continued) Description Group Configurable field. Enter a group to categorize the EDS-MD. Doubleclick the field, type in the value, and press Enter to complete. This group name is local to this PC and is not visible on other PCs or laptops using DeviceInstaller. Comments Configurable field. Enter comments for the EDS-MD. Double-click the field, type in the value, and press Enter to complete.
5: Configuration Using Web Manager This chapter describes how to configure the EDS-MD4, EDS-MD8 and EDS-MD16 using Web Manager, the Lantronix browser-based configuration tool. The unit’s configuration is stored in nonvolatile memory and is retained without power. All changes take effect immediately, unless otherwise noted.
5: Configuration Using Web Manager Device Status Page The Device Status page is the first page that appears after you log into the Web Manager. It also appears when you click Status in the Main Menu.
5: Configuration Using Web Manager Web Manager Page Components The layout of a typical Web Manager page is below. Figure 5-1 Components of the Web Manager Page Items to configure Links to subpages Logout button Header Menu Bar Footer Configuration and/or Status Area Information and Help Area The menu bar always appears at the left side of the page, regardless of the page shown. The menu bar lists the names of the pages available in the Web Manager. To bring up a page, click it in the menu bar.
5: Configuration Using Web Manager The information or help area shows information or instructions associated with the page. A Logout link is available at the upper right corner of every web page. In Chrome or Safari, it is necessary to close out of the browser to completely logout. If necessary, reopen the browser to log back in. The footer appears at the very bottom of the page. It contains copyright information and a link to the Lantronix home page.
5: Configuration Using Web Manager Web Manager Page (continued) Description See Page Syslog Lets you specify the severity of events to log and the server and ports to which the syslog should be sent. 53 System Lets you reboot device, restore factory defaults, upload new firmware, and change the device long and short names. 74 Terminal Lets you change current settings for a terminal. 49 Tunnel Lets you change the current configuration settings for a tunnel.
6: Line and Tunnel Settings The EDS-MD4, EDS-MD8 and EDS-MD16 contains four, eight or sixteen Lines, depending on the specific model. All lines use standard RS232 serial ports. RS232/RS485 All lines can be configured to operate in the following modes: RS232 All serial settings such as Baud Rate, Parity, Data Bits, etc, apply to these Lines. Line Settings The Line Settings allow configuration of the serial Lines (ports). Some settings may be specific to only certain Lines.
6: Line and Tunnel Settings Table 6-2 Line Command Mode Settings Line Command Mode Settings Mode Description Set the Command Mode state of the Line. When in Command Mode, a CLI session operates exclusively on the Line. Choices are: Always User Serial String Disabled Note: In order to enable Command Mode on the Line, Tunneling on the Line must be Disabled (both Connect and Accept modes). Also, custom baud rates are not supported in Command Mode.
6: Line and Tunnel Settings Using the CLI To view Line statistics: enable -> line 1, show statistics Using XML Include in your file: Tunnel Settings Tunneling allows serial devices to communicate over a network, without “being aware” of the devices which establish the network connection between them. Tunneling parameters are configured using the Tunnel menu and submenus.The Tunnel settings allow you to configure how the Serial-Network tunneling operates.
6: Line and Tunnel Settings Using the CLI To enter Tunnel 1 command level: enable -> tunnel 1 -> serial Using XML Include in your file: Packing Mode With Packing, data from the serial Line is not sent over the network immediately. Instead, data is queued and sent in segments, when either the timeout or byte threshold is reached. Packing applies to both Accept and Connect Modes.
6: Line and Tunnel Settings Using the CLI To enter the Tunnel 1 Packing command level: enable -> tunnel 1 -> packing Using XML Include in your file: Accept Mode In Accept Mode, the EDS-MD4/8/16 listens (waits) for incoming connections from the network. A remove node on the network initiates the connection. The configurable local port is the port the remote device connects to for this connection. There is no remote port or address.
6: Line and Tunnel Settings Tunnel Accept Mode Settings (continued) Flush Serial Description Set whether the serial Line data buffer is flushed upon a new network connection. Choices are: Block Serial Set whether Block Serial is enabled for debugging purposes. Choices are: Block Network Enabled = if Enabled, incoming characters from the Serial Line will not be forwarded to the network.
6: Line and Tunnel Settings Connect Mode In Connect Mode, theEDS-MD4/8/16 continues to attempt an outgoing connection on the network, until established. If the connection attempt fails or the connection drops, then it retries after a timeout. The remote node on the network must listen for the Connect Mode’s connection. For Connect Mode to function, it must be enabled, have a remote station (node) configured, and a remote port configured (TCP or UDP). When established, Connect Mode is always on.
6: Line and Tunnel Settings Tunnel Connect Mode Settings (continued) Block Serial Description Set whether Block Serial is enabled for debugging purposes. Choices are: Block Network Enabled = If Enabled, incoming characters from the Serial Line will not be forwarded to the network. Instead, they will be buffered and will eventually flow off the Serial Line if hardware or software flow control is configured.
6: Line and Tunnel Settings Tunnel Disconnect Mode Settings Description Modem Control Set whether Modem Control enables disconnect when the Modem Control pin is not asserted on the Serial Line. Choices are: Enabled Disabled (default) Timeout Enter the number of milliseconds a tunnel may be idle before disconnection. The value of zero disables the idle timeout. Flush Serial Data Set whether to flush the Serial Line when the Tunnel is disconnected.
6: Line and Tunnel Settings Tunnel Modem Emulation Settings Response Type Description Select a representation for the Modem Response Codes sent out on the Serial Line. Choices are: Error Unknown Commands Set whether the Error Unknown Commands is enabled (ATU0) and ERROR is returned on the Serial Line for unrecognized AT commands. OTherwise (ATU1) OK is returned for unrecognized AT commands.
6: Line and Tunnel Settings Using the CLI To view Tunnel 1 statistics: enable -> tunnel 1, show statistics Using XML Include in your file: EDS-MD User Guide 45
7: Network Settings The Network Settings show the status of the Ethernet interface/link and let you configure the settings on the device. Interface settings are related to the configuration of the IP and related protocols. Link settings are related to the physical link connection, which carries the IP traffic. The EDS-MD4, EDS-MD8 and EDS-MD16 contains one network interface. The Ethernet interface is also called interface 1 or eth0. Notes: Some settings require a reboot to take effect.
7: Network Settings Network Interface Settings (continued) Description Hostname Enter the hostname for the interface. It must begin with a letter or number, continue with a sequence of letters, numbers, or hyphens, and end with a letter or number. Note: This setting will take effect immediately, but will not register the hostname with a DNS server until the next reboot. Domain Enter the domain name suffix for the interface.
7: Network Settings Network Link Settings Physical link parameters can be configured for an Ethernet (eth0) Network Interface (see Table 7-2). Table 7-2 Network 1 (eth0) Link Settings Network 1 Ethernet (eth0) Link Settings Description Speed Select the Ethernet link speed. (Default is Auto) Duplex Auto = Auto-negotiation of Link Speed 10 = Force 10 Mbps 100 = Force 100 Mbps Select t he Ethernet link duplex mode.
8: Terminal and Host Settings Predefined connections are available via telnet, ssh, or a serial port. A user can choose one of the presented options and the device automatically makes the predefined connection. Either the Telnet, SSH, or serial port connection can present the CLI or the Login Connect Menu. By default, the CLI is presented when the device is accessed. When configured to present the Login Connect Menu, the hosts configured via the Host selections, and named serial lines are presented.
8: Terminal and Host Settings To Configure the Terminal Network Connection Using Web Manager To configure the Terminal on Network, click Terminal on the menu and select Network -> Configuration.
8: Terminal and Host Settings Host Settings (continued) Description SSH Username Enter a username to select a pre-configured Username/Password/ Key (configured on the SSH: Client Users), or leave it blank to be prompted for a username and password at connect time. Note: This field appears if you selected SSH as the protocol. Remote Address Enter an IP address for the host to which the device will connect. Remote Port Enter the port on the host to which the device will connect.
9: Services Settings DNS Settings This section describes the active run-time settings for the domain name system (DNS) protocol. The primary and secondary DNS addresses come from the active interface. The static addresses from the Network Interface configuration settings may be overridden by DHCP. Note: The blue text in the XML command strings of this chapter are to be replaced with a user-specified name.
9: Services Settings FTP Settings The FTP protocol can be used to upload and download user files, and upgrade the EDS-MD4/8/16 firmware. A configurable option is provided to enable or disable access via this protocol. Table 9-2 FTP Settings FTP Settings Description State Select to enable or disable the FTP server: Enabled (default) Disabled To Configure FTP Settings Using Web Manager To configure FTP, click FTP in the menu.
9: Services Settings Syslog Settings (continued) Severity Log Level Description Specify the minimum level of system message the EDS-MD should log. This setting applies to all syslog facilities. The drop-down list in the Web Manager is in descending order of severity (e.g., Emergency is more severe than Alert.) To View or Configure Syslog Settings: Using Web Manager To configure the Syslog, click Syslog in the menu.
9: Services Settings HTTP Settings (continued) Description Max Timeout Enter the maximum time for the HTTP server to wait when receiving a request. This prevents Denial-of-Service (DoS) attacks. The default is 10 seconds. Max Bytes Enter the maximum number of bytes the HTTP server accepts when receiving a request. The default is 40 KB (this prevents DoS attacks).
9: Services Settings HTTP Authentication Settings Description Auth Type Select the authentication type: None = no authentication is necessary. Basic = encodes passwords using Base64. Digest = encodes passwords using MD5. SSL = can only be accessed over SSL (no password is required). SSL/Basic = is accessible only over SSL and encodes passwords using Base64. SSL/Digest = is accessible only over SSL and encodes passwords using MD5.
9: Services Settings Using the CLI To enter the RSS command level: enable -> config -> rss Using XML Include in your file: Real Time Clock (RTC) Settings The current date and time displayed on the EDS-MD can be modified. Table 9-7 RTC Settings RTC Settings Description Time Zone Select the time zone corresponding to the location of the EDS-MD.
10: Security Settings The EDS-MD4, EDS-MD8 and EDS-MD16 device supports Secure Shell (SSH) and Secure Sockets Layer (SSL). SSH is a network protocol for securely accessing a remote device. SSH provides a secure, encrypted communication channel between two hosts over a network. It provides authentication and message integrity services. Secure Sockets Layer (SSL) is a protocol that manages data transmission security over the Internet.
10: Security Settings RSS Settings (continued) Description Public Key Enter the path and name of the existing public key you want to upload. In WebManager, you can also Browse to the public key to be uploaded. Key Type Select a key type to use for the new key: Bit Size RSA DSA Select a bit length for the new key: 512 768 1024 Note: SSH Keys from other programs may be converted to the required EDS-MD format. Use Open SSH to perform the conversion.
10: Security Settings Table 10-3 SSH Server Authorized Users RSS Settings Description Username Enter a new username or edit an existing one. Password Enter a new password or edit an existing one. Public RSA Key Enter the path and name of the existing public RSA key you want to use with this user. In WebManager, you can also Browse to the public RSA key to be uploaded. If authentication is successful with the key, no password is required.
10: Security Settings RSS Settings (continued) Bit Size Description Select the bit length of the new key: 512 768 1024 Using a larger Bit Size takes more time to generate the key. Approximate times are: 1 second for a 512 bit RSA key 1 second for a 768 bit RSA key 1 second for a 1024 bit RSA key 2 seconds for a 512 bit DSA key 2 seconds for a 768 bit DSA key 20 seconds for a 1024 bit DSA key Note: Some SSH clients require RSA host keys to be at least 1024 bits long.
10: Security Settings Certificate and Key Generation The EDS-MD4, EDS-MD8 and EDS-MD16 can generate self signed certificates and their corresponding keys. This can be done for both the rsa and dsa certificate formats. Certificates can be identified on the EDS-MD4/8/16 by a name provided at generation time.
10: Security Settings Using XML Not applicable. Certificate Upload Settings SSL certificates identify the EDS-MD4/8/16 to peers. Certificate and key pairs can be uploaded to the EDS-MD4/8/16 through either the CLI or XML import mechanisms. Certificates can be identified on the EDS-MD4/8/16 by a name provided at upload time. Table 10-6 Upload Certificate Settings Upload Certificate Settings Description New Certificate SSL certificate to be uploaded. RSA or DSA certificates are allowed.
10: Security Settings Trusted Authorities One or more authority certificates are needed to verify a peer's identity. These certificates do not require a private key. Table 10-7 Trusted Authority Settings Trusted Authorities Settings Description Authority SSL authority certificate. RSA or DSA certificates are allowed. The format of the authority certificate can be PEM or PKCS7. PEM files must start with “-----BEGIN CERTIFICATE-----” and end with “----END CERTIFICATE-----”.
11: Maintenance and Diagnostics Settings Filesystem Settings Use the file system to list, view, add, remove, and transfer files. The EDS-MD4/8/16 uses an EXT3 flash file system to store files. This is a journalled file system, which means that changes to the file system are recorded before the actual changes themselves are made. In the event of power loss, the use of journaling can usually recover from changes that had been started but not completed. Some file systems may contain a 'lost+found' directory.
11: Maintenance and Diagnostics Settings File Modification The EDS-MD4/8/16 allows for the creation and removal of files on its filesystem. Table 11-2 File Modification Settings File Modification Commands Description rm Removes the specified file from the file system. touch Creates the specified file as an empty file. cp Creates a copy of a file. mkdir Creates a directory on the file system. rmdir Removes a directory from the file system. format Format the file system and remove all data.
11: Maintenance and Diagnostics Settings To Transfer or Modify Filesystem Files Using Web Manager To create a new file or directory, upload an existing file, copy or move a file, click Filesystem in the menu and select Browse. Using the CLI To enter the Filesystem command level: enable -> filesystem Using XML Not applicable. IP Network Stack Settings There are various low level network stack specific items that are available for configuration.
11: Maintenance and Diagnostics Settings Table 11-5 ICMP Network Stack Settings Protocol Stack ICMP Settings Description State The State selection is used to turn on/off processing of ICMP messages. This includes both incoming and outgoing messages. Choose Enabled or Disabled. To Configure ICMP Network Stack Settings Using Web Manager To configure ICMP protocol settings, click Protocol Stack in the menu and select ICMP.
11: Maintenance and Diagnostics Settings Table 11-7 SMTP Network Stack Settings Protocol Stack SMTP Settings Description Relay Address Address of all outbound email messages through a mail server. Can contain either a hostname or an IP address. Relay Port Port utilized for the delivery of outbound email messages. To Configure SMTP Network Stack Settings Using Web Manager To configure SMTP protocol settings, click Protocol Stack in the menu and select SMTP.
11: Maintenance and Diagnostics Settings Using XML Include in your file: and Diagnostics The EDS-MD4/8/16 has several tools for diagnostics and statistics. Various options allow for the configuration or viewing of IP socket information, ping, traceroute, memory, and processes. Hardware To View Hardware Information Using Web Manager To view hardware information, click Diagnostics in the menu and select Hardware.
11: Maintenance and Diagnostics Settings Table 11-9 Ping Settings Diagnostics: Ping Settings Description Host Enter the IP address or host name for the EDS-MD to ping. Count Enter the number of ping packets EDS-MD should attempt to send to the Host. The default is 5. Timeout Enter the time, in seconds, for the EDS-MD to wait for a response from the host before timing out. The default is 5 seconds.
11: Maintenance and Diagnostics Settings Log Table 11-11 Log Settings Diagnostics: Log Output Description Select a diagnostic log output type: Max Length Disable - Turn off the loggin feature. Filesystem - Directs logging to /log.txt. Line (1, 2, 3 and 4) - Directs logging to the selected serial line. Set the maximum length of the log.txt file. Note: This setting becomes available when Filesystem is selected.
11: Maintenance and Diagnostics Settings Processes The EDS-MD4/8/16 Processes information shows all the processes currently running on the system. It shows the Process ID (PID), Parent Process ID (PPID), user, CPU percentage, percentage of total CPU cycles, and process command line information. To View Process Information Using Web Manager To view process information, click Diagnostics in the menu and select Processes.
11: Maintenance and Diagnostics Settings System Settings The EDS-MD4/8/16 System settings allow for rebooting the device, restoring factory defaults, uploading new firmware and updating a system’s short and long name. Note: Anytime you reboot the unit, this operation will take some time to complete. Please wait a minimum of 5 seconds after rebooting the unit before attempting to make any subsequent connections. Table 11-12 System Settings System Settings Description Reboot Device Reboots the device.
12: Advanced Settings Email Settings View and configure email alerts relating to events occurring within the system. Table 12-1 Email Configuration Email – Configuration Settings Description To Enter the email address to which the email alerts will be sent. Multiple addresses are separated by semicolon (;). Required field if an email is to be sent. CC Enter the email address to which the email alerts will be copied. Multiple addresses are separated by semicolon (;).
12: Advanced Settings Using the CLI To enter Email command level: enable -> email 1 Using XML Include in your file: Command Line Interface Settings The Command Line Interface settings allow you to control how users connect to and interact with the EDS-MD4/8/16's command line. It is possible to configure access via the Telnet and SSH protocols, in addition to general CLI options.
12: Advanced Settings Telnet Settings The telnet settings control CLI access to the EDS-MD4/8/16 over the Telnet protocol. Table 12-3 Telnet Settings Telnet Settings Description Telnet State Enable or Disable CLI access via telnet Telnet Port Enter an alternative Telnet Port to override the default used by the CLI server. Blank the field to restore the default. Telnet Max Sessions Specify the maximum number of concurrent Telnet sessions that will be allowed.
12: Advanced Settings To Configure SSH Settings Using Web Manager To configure SSH settings, click CLI in the menu and select Configuration. Using the CLI To enter the SSH command level: enable -> config -> cli -> ssh Using XML Include in your file: and XML Settings The EDS-MD4/8/16 allows for the configuration of units using an XML configuration record (XCR).
12: Advanced Settings XML Export Configuration Settings (continued) Description Groups to Export Check the configuration groups that are to be exported to the XML configuration record. The group list should be comma delimited and encased in double quotes. The list of available groups can be viewed with the “xcr list” command. To Export Configuration in XML Format Using Web Manager To export configuration format, click XML in the menu and select Export Configuration.
12: Advanced Settings Using XML Not applicable. XML: Import Configuration Here you can import a system configuration from an XML file. The XML data can be imported from a file on the file system or pasted into a CLI session. The groups to import can be specified at the command line, the default is all groups. Import Configuration from External File This import option requires entering the path and file name of the external XCR file you want to import.
13: Updating Firmware Obtaining Firmware Obtain the most up-to-date firmware and release notes for the unit from the Lantronix Web site (www.lantronix.com/support/downloads/) or by using anonymous FTP (ftp://ftp.lantronix.com/). Loading New Firmware Firmware may be updated by sending the file to the EDS-MD4/8/16 over an FTP connection. The destination file name on the EDS-MD4, EDS-MD8 or EDS-MD16 must be "firmware.rom". The device will reboot upon successful completion of the firmware upgrade.
14: VIP Settings Virtual IP (VIP) Configuration Configuring Connect Mode tunnels to use VIP is a simple matter of configuring a tunnel as is normally done, but also enabling VIP in the Tunnel Host settings, and using a VIP Name for the address. VIP Accept Mode tunnels do not require special configuration. If VIP access is enabled (in VIP configuration), then VIP Accept Mode requests from a ManageLinx device will be accepted.
14: VIP Settings Using XML Include in your file: Virtual IP (VIP) Counters Table 14-2 VIP Counters VIP Counters Description Data Bytes Total bytes in the TCP packets (not the UDP packets) UDP Packet Queue The number of packets queued for transmission. UDP Packets The number of packets transmitted. Note: UDP counts are packet based, and do not record the number of data bytes. To View VIP Counters Using Web Manager Click VIP on the menu and select Counters.
15: Branding the EDS-MD4/8/16 This chapter describes how to brand your EDS-MD4, EDS-MD8 or EDS-MD16 by using Web Manager and Command Line Interface (CLI). It contains the following sections on customization: Web Manager Customization Short and Long Name Customization Web Manager Customization Customize the Web Manager's appearance by modifying index.html, style.css, and the product logo. The style (fonts, colors, and spacing) of the Web Manager is controlled with style.css.
15: Branding the EDS-MD4/8/16 Short and Long Name Customization You can customize the short and long names in your EDS-MD4/8/16. The names display in the CLI show command and in the System web page in the Current Configuration table. The short name is used for the show command. Both names display in the CLI Product Type field. Table 15-1 Short and Long Name Settings Name Settings Description Short Name Enter a short name for the system name. A maximum of 32 characters are allowed.
Appendix A: Technical Support If you are unable to resolve an issue using the information in this documentation, please contact Technical Support: Technical Support US Check our online knowledge base or send a question to Technical Support at http://www.lantronix.com/support. Technical Support Europe, Middle East, Africa Phone: +33 13 930 4172 Email: eu_techsupp@lantronix.com or eu_support@lantronix.com Firmware downloads, FAQs, and the most up-to-date documentation are available at http://www.lantronix.
Appendix B: Binary to Hexadecimal Conversions Many of the unit's configuration procedures require you to assemble a series of options (represented as bits) into a complete command (represented as a byte). The resulting binary value must be converted to a hexadecimal representation. Use this chapter to learn to convert binary values to hexadecimals or to look up hexadecimal values in the tables of configuration options.
Figure 17-2 Windows Scientific Calculator 4. Click Hex. The hexadecimal value appears.
Appendix C: Compliance (According to ISO/IEC Guide 22 and EN 45014) Manufacturer's Name & Address: Lantronix 167 Technology Drive, Irvine, CA 92618 USA Product Name Model: EDS-MD4, EDS-MD8 and EDS-MD16 Port Device Servers Conform to the following standards or other normative documents: Table 18-1 Applicable Medical Standards Emissions Immunity EN 60601-1-2: 2007 EN 60601-1-2: 2007 CISPR 11:2003+A1:2004+A2:2006 EN 61000-4-2: 2009 EN 61000-3-2: 2006 + A1: 2009 + A2: 2009 EN 61000-4-3: 2006 + A1: 2008
Table 18-3 Regulatory Compliance Standard Description United States: UL 60950-1: 2nd edition Standard for Safety for Information Technology Equipment – Safety – Part 1: General Requirements United States: UL 60601-1: 1st edition Standard for Safety for Medical Electrical Equipment, Part 1: General Requirements for Safety Canada: CAN/CSA-C22.2 No. 60950-1-07 2nd edition Standard for Safety for Information Technology Equipment – Safety – Part 1: General Requirements Canada: CAN/CSA C22.2 No. 601.
Figure 18-4 Suppliers Declaration of Conformity EDS-MD User Guide 91
RoHS Notice All Lantronix products in the following families are China RoHS-compliant and free of the following hazardous substances and elements: Lead (Pb) Cadmium (Cd) Product Family Name UDS1100 and 2100 EDS MSS100 IntelliBox XPress DR & XPress-DR+ SecureBox 1101 & 2101 WiBox UBox MatchPort SLC XPort WiPort SLB SLP SCS SLS DSC PremierWave Micro125 Mercury (Hg) Hexavalent Chromium (Cr (VI)) Polybrominated biphenyls (PBB) Polybrominated diphenyl ethers (PBDE) Toxic or hazardous Substances
Appendix D: Lantronix Cables, Adapters and Serial Port Pinouts Lantronix cables and adapters for use with EDS-MD4, EDS-MD8 and EDS-MD16 are listed here according to part number and application. Cables and Adapters Table 19-1 Lantronix Cables and Adapters Lantronix P/N Description Applications 500-153 RJ45-to DB9F Connects the RJ45 RS232 serial ports of EDS-MD to a DB9M DTE interface of a PC or serial device to check that serial ports in the EDSMD are functioning properly. 200.
Adapters and Serial Port Pinouts Figure 19-2 RJ45 Receptacle to DB25M DTE Adapter (PN 200.2066A) Figure 19-3 RJ45 Receptacle to DB25M DCE Adapter (PN 200.
Figure 19-4 RJ45 Receptacle to DB25F DTE Adapter (PN 200.2067A ) Figure 19-5 RJ45 Receptacle to DB25F DCE Adapter (PN 200.
Figure 19-6 RJ45 Receptacle to DB9M DTE Adapter (PN 200.2069A) Figure 19-7 RJ45 Receptacle to DB9M DCE Adapter (PN 200.
Figure 19-8 RJ45 Receptacle to DB9F DTE Adapter (PN 200.2070A) Figure 19-9 RJ45 Receptacle to DB9F DCE Adapter (PN 200.
Figure 19-10 RJ45 to RJ45 Adapter (ADP010104-01) Note: The cable ends of the ADP010104-01 are an RJ45 socket on one end and a RJ45 plug on the other instead of RJ45 sockets on both ends.
