EPS Installation Guide For EPS1 and EPS2 Ethernet Print Servers
The information in this guide may change without notice. The manufacturer assumes no responsibility for any errors which may appear in this guide. AppleTalk, Chooser, and Macintosh are trademarks of Apple Computer Corporation. LaserJet and Bitronics are trademarks of Hewlett Packard. Centronics is a registered trademark of Centronics Data Computer Corporation. PostScript is a trademark of Adobe Systems, Inc. DEC and LAT are trademarks of Digital Equipment Corporation.
Contents 1: Introduction.......................................................................... 1-1 1.1 How to Use This Manual................................................................. 1-1 2: Installation............................................................................ 2-1 2.1 EPS1/2 Product Description ............................................................ 2-1 2.2 Installing the EPS ............................................................................
Contents 5.4 PCONSOLE Print Queues............................................................... 5-3 5.5 NetWare Host Troubleshooting....................................................... 5-4 6: LAT Configuration ............................................................... 6-1 6.1 Printing Directly to a Port................................................................ 6-1 6.2 LAT Host Troubleshooting.............................................................. 6-2 7: AppleTalk Configuration ....
Contents E: Specifications ......................................................................E-1 E.1 Power Information .......................................................................... E-1 E.2 Environmental Limitations.............................................................. E-1 F: Frequently-used Commands ..............................................F-1 F.1 Conventions..................................................................................... F-1 F.2 Server Commands .........
1: Introduction The Lantronix EPSs (EPS1 and EPS2) are ethernet print servers that provide shared network access to printers for a variety of network protocols and operating systems. The print servers support the TCP/IP, IPX (NetWare), Local Area Transport (LAT), AppleTalk (EtherTalk), and Microsoft LAN Manager protocols. They can queue multiple pending jobs and service those jobs in the order in which they are received from hosts.
How to Use This Manual ❍ Introduction Appendix F, Frequently-used Commands Read chapters 2 through 4 in order, then proceed to the protocol-specific chapter that relates to your network. Refer to Appendix F as needed. The Print Server Reference Manual, located on the CD-ROM and web site, provides additional information about configuring and using your EPS.
2: Installation This chapter describes the various EPS models and shows how to install them into a basic network situation. 2.1 EPS1/2 Product Description The front panel of the EPS has an RJ45 serial connector and either one (EPS1) or two (EPS2) DB25 parallel connectors. The port names are Port_1 (serial), Port_2 (top parallel), and Port_3 (bottom parallel, EPS2 only).
EPS1/2 Product Description Installation The top panel of the EPS has 7 LEDs. Table 2-1 explains their functions during normal operation. Table 2-1: LED Functionality 2-2 LED Function During Normal Operation PWR Lights solid green to indicate that the unit has power. POLARITY Lights solid yellow to indicate that the 10BASE-T cable is swapped. GOOD LINK Lights solid green to indicate a working Ethernet connection (either 10BASE-T or 10BASE2).
Installation Installing the EPS 2.2 Installing the EPS The following diagram shows a properly-installed EPS: 10BASE-T 4 3 2b Serial Printer EPS2 2a Parallel Printers To install the EPS, complete the following steps in order. Refer to the numbers in the figure for help. 1 Set the DIP switches on the bottom of the unit. Their functions are explained in Table 2-2. Table 2-2: DIP Switch Functions Switch Position 1 Position 0 (default) 1 Factory NVR: EPS is restored to factory defaults at power-up.
Installing the EPS 3 Installation Attach the EPS to the network using a 10BASE-T cable, transceiver, or AUI cable. The EPS must have one and only one valid Ethernet connection in order to boot properly. Use switch 4 to set the correct Ethernet connection type. To boot the EPS without attaching it to the network, attach a terminated MAU to the AUI port or connect the 10BASE-T port to a disabled hub port. 4 Attach one end of the power cable to the EPS; plug the other end into an electrical outlet.
3: Getting Started It is important to consider the following points before logging into and configuring the EPS: ◆ You must configure the EPS IP address before any TCP/IP functionality is available. (See Setting the IP Address on page 4-1) You cannot use the ThinWeb Manager until you have configured an IP address. ◆ Changing any server, service, or port setting requires privileged user status. The default privileged password is system. ◆ The login password is required for remote console logins.
Services Getting Started Incoming Telnet is only possible if your EPS has an IP address configured. Incoming Telnet is enabled by default to allow TCP/IP connections. To change this setting, use the Define Server Incoming command described in the Command Reference chapter of the Print Server Reference Manual located on the CD-ROM. Incoming logins do not prompt for a login password, so you may wish to disable them for security reasons.
4: TCP/IP Configuration The EZWebCon configuration software is the easiest way to configure the EPS. The following sections cover IP address configuration and print configuration methods for TCP/ IP hosts. 4.1 Setting the IP Address The EPS IP address must be configured before any TCP/IP functionality is available. Use one of the following methods to set the IP address: EZWebCon; a directed Ping packet; a BOOTP, DHCP, or RARP reply; or commands entered via the command line interface. 4.1.
Setting the IP Address TCP/IP Configuration On a UNIX host, create an entry in the host’s ARP table and substitute the intended IP address and the hardware address of the EPS, then ping the EPS. This process typically requires superuser privileges. Figure 4-1: ARP and Ping on UNIX # arp -s 192.0.1.228 00-80-a3-xx-xx-xx % ping 192.0.1.228 In order for the ARP command to work on Windows, the ARP table on the PC must have at least one IP address defined other than its own.
TCP/IP Configuration LPR Printing 4.1.3 Using a BOOTP, DHCP, or RARP Reply At boot time a host-based DHCP, BOOTP, or RARP server can respond to an EPS request for an available IP address. For information about configuring the DHCP, BOOTP, or RARP server, see your host documentation. 4.1.4 Using the Command Line Interface 1 Connect to the serial port (Port_1) using a console terminal or a terminal emulation program, and press Return. The serial port settings are 9600 baud, 8 bits, 1 stop bit, no parity.
LPR Printing TCP/IP Configuration ◆ The EPS cannot print multiple copies of the print job when using the “-#n” lpr option. ◆ If two print queues on the host refer to two services on the same EPS, they must use separate spooling directories. ◆ No special purpose input or output filters can be used when printing via LPR. If this functionality is necessary, use the named pipe interface program in the RTEL print queue configuration software. 4.2.1 LPR on Windows NT 3.5.
TCP/IP Configuration 4 Select the Add Port button and click Next. 5 Select LPR Port. Note: 6 LPR Printing If LPR Port is not an option, open the Network Control Panel and add “Microsoft TCP/IP Printing” to the List of services. Enter the name or IP address of your EPS on the first line, and enter the name of your EPS print service on the second line.
LPR Printing TCP/IP Configuration 7 Select the manufacturer and printer type. 8 Enter the queue name. 9 If applicable, choose Shared and select the type of operating system that the printer will be working with. (First confirm that the print queue is working.
TCP/IP Configuration LPR Printing 10 Test the printer by choosing Yes and clicking Finish. 4.2.2 LPR on Windows 95/98 To enable LPR printing on Windows 95/98, you must download and install the LPR for Windows 95/98 application from the Lantronix FTP site (ftp.lantronix.com). 1 On the FTP home page, click on pub. 2 Click on lpr_win32. 3 Download the file ltxlpr.exe. 4 Install the file ltxlpr.exe. Once installation is complete, a readme file will open automatically.
LPR Printing 2 TCP/IP Configuration Add the host print queue to the /etc/printcap file. The punctuation shown in Figure 4-7 is required, and no extra spaces should be added. Figure 4-7: Adding /etc/printcap Entry eps_prt|Printer on LAB EPS:\ :rm=EPS_xxxxxx:\ :rp=EPS_xxxxxx_TEXT:\ :sd=/usr/spool/lpd/eps_prt: This will create a host queue named eps_prt.
TCP/IP Configuration LPR Printing To add a print queue: 1 From the main window, choose Print Spooling. 2 Choose Manage Print Server and Manage Print Queues. 3 Choose Add a print queue. 4 From the dialog box that appears, choose remote. 5 From the next dialog box, choose Remote Printing. 6 The Add a Standard Remote Print Queue dialog box will appear. Enter the following information.
LPR Printing 5 TCP/IP Configuration The Add Remote Printer window will appear. SAM will prompt you for: ❍ The printer name (the name of the print queue), ❍ The remote system name (the EPS name), ❍ The remote printer name (the EPS service), ❍ The remote cancel model, and ❍ The remote status model. 4.2.6 LPR on SCO UNIX Hosts LPR is supported in SCO V3.2 release 4 with TCP/IP Version 1.2 and greater. To configure a print queue using LPR, issue the mkdev rlp command.
TCP/IP Configuration 2 LPR Printing Answer the questions that follow. Figure 4-11: Configuring Remote Printer Remote Printing Configuration Enter information for remote printers or local printers accepting remote printing requests Please enter the printer name (q to quit): backupprinter Is printer backupprinter a remote printer or a local printer? (r/l) r Please enter the name of the remote host that backupprinter is attached to: EPS_xxxxxx The backupprinter is connected to host EPS_xxxxxx.
Unix Host Troubleshooting TCP/IP Configuration To recreate the RTEL source files: 1 Copy the file RTEL_SRC.TAR in binary mode from the distribution CD-ROM to the UNIX host. 2 Untar the archive. 3 See the README files in the created directories that describe the contents of the RTEL distribution and man pages that describe the actual software functionality. 4.
5: NetWare Configuration The EZWebCon configuration software is the easiest way to configure the EPS. The following sections cover print configuration methods for NetWare hosts. Note: The EPS needs an IP address before you can use EZWebCon. See Setting the IP Address on page 4-1 for instructions. This chapter explains creating NDS print queues with NetWare Administrator and with the PCONSOLE Quick Setup option. To create NDS print queues, you must be running NetWare version 4.x with NDS capabilities.
NetWare Administrator Quick Setup Print Queues NetWare Configuration 5.2.2 Configure your EPS 1 License NDS on your EPS using the string obtained from Lantronix. Figure 5-1: Licensing NDS Local>> DEFINE PROTOCOL NETWARE DSLICENSE licensestring 2 Define the directory service tree in which the EPS is located.
NetWare Configuration PCONSOLE Print Queues To create a print queue with the Quick Setup option: 1 Start the NetWare Administrator. 2 In the Directory Tree windows, select the context in which to install the printer. 3 From the Menu Bar, select Tools: Print Services Quick Setup. 4 In the Print Server Name field, enter the name of your EPS (viewable by entering the Show Server command at the Local> prompt).
NetWare Host Troubleshooting NetWare Configuration 5.5 NetWare Host Troubleshooting Table 5-1: NetWare Host Troubleshooting (Bindery Mode) Area to Check Explanation The print server names in PCONSOLE match the EPS name and its service name Use PCONSOLE to check. The EPS NetWare access table Use the Show Protocols NetWare Access command. Scanning too many file servers can cause a delay between jobs. Configure the access list to only scan for jobs on the file servers of interest.
NetWare Configuration NetWare Host Troubleshooting Table 5-3: NDS Errors from the File Server Code Meaning Remedy 0xfffffda7 Object could not be found in the given context Check the EPS server name, DScontext, and DStree to ensure the printer server is set up correctly with PCONSOLE. 0xfffffda5 Requested attribute could not be found Use PCONSOLE to ensure that the EPS has associated printers and the printers have associated queues.
6: LAT Configuration The EZWebCon configuration software is the easiest way to configure the EPS. The following sections cover print configuration methods for LAT hosts. Note: The EPS needs an IP address before you can use EZWebCon. See Setting the IP Address on page 4-1 for instructions. LAT print queues can be created by printing to a port or printing to a service. Printing directly to a port requires no EPS configuration. Note: Printing directly to a port is the easiest method for printing to the EPS.
LAT Host Troubleshooting LAT Configuration 6.2 LAT Host Troubleshooting By default, the LAT error message codes on the host are not translated into text error messages. If a LAT job fails and appears in the queue with an eight-digit hex result code, the code can be translated by issuing the following commands: Figure 6-4: Translating LAT Error Codes $ SHOW QUEUE/FULL/ALL queue_name (note the error code nnnnnnnn) $ SET MESSAGE SYS$MESSAGE:NETWRKMSG.
7: AppleTalk Configuration The EZWebCon configuration software is the easiest way to configure the EPS. The following sections cover print configuration methods for AppleTalk hosts. Note: The EPS needs an IP address before you can use EZWebCon. See Setting the IP Address on page 4-1 for instructions. Note: Macintoshes that do not support EtherTalk will need either an Ethernet card or a LocalTalk-to-EtherTalk router to use the EPS. 7.
AppleTalk Host Troubleshooting AppleTalk Configuration 7.4 AppleTalk Host Troubleshooting Table 7-1: AppleTalk Host Troubleshooting Area to Check Explanation The printer is available to be selected in the Chooser Make sure the printer is in the right zone. Bidirectional communication Lock the printer in PostScript mode and issue the Test Service PostScript Count n command. This sends a job to the printer and waits for the response.
8: DLC Configuration for LAN Manager The EZWebCon configuration software is the easiest way to configure the EPS. This chapter explains DLC/Digital Network Port configuration for Windows NT 4.x hosts. Note: The Server needs an IP address before you can use EZWebCon. See Setting the IP Address on page 4-1 for instructions. Printing using an LPD client is the preferred method for sending print jobs to the EPS. Windows 95 does not support DLC printing (see Chapter 4 for more information). 8.
DLC Configuration 7 Select Job-based. 8 Select the manufacturer and printer type. 9 Enter the queue name. DLC Configuration for LAN Manager 10 If applicable, choose Shared and select the operating system the printer will be working with. (First confirm that the print queue is working.) 11 Test the printer.
A: Contact Information If you are experiencing an error that is not listed in Appendix B: or if you are unable to fix the error, contact your dealer or Lantronix Technical Support at 800-422-7044 (US) or 949453-3990. Technical Support is also available via Internet email at support@lantronix.com. A.
B: Troubleshooting This Appendix discusses how to diagnose and fix errors quickly yourself without having to contact a dealer or Lantronix. It will help to connect a terminal to the serial port while diagnosing an error to view any summary messages that are displayed. When troubleshooting, always ensure that the physical connections (power cable, network cable, and serial cable) are secure.
Power-up Troubleshooting Troubleshooting Problem situations and error messages are listed in Table B-2. If you cannot find an explanation for your problem, try to match it to one of the other errors. If you cannot remedy the problem, contact your dealer or Lantronix Technical Support. Table B-2: Power-up Problems and Error Messages Problem/Message Error Remedy The EPS is The unit or its power supply is connected to a power damaged. source, but there is no LED activity.
Troubleshooting DHCP Troubleshooting Table B-2: Power-up Problems and Error Messages, cont. Problem/Message Error Remedy The terminal shows a The EPS is not connected Boot> prompt rather properly to the Ethernet. than a Local> prompt. The EPS Ethernet address is invalid. Ensure that the EPS is firmly connected to a functional and properly-terminated network node. The EPS passes power-up diagnostics, but attempts to download new Flash ROM code from a network host.
BOOTP Troubleshooting Troubleshooting B.3 BOOTP Troubleshooting If the BOOTP request is failing and you have configured your host to respond to the request, check these areas: Table B-4: BOOTP Troubleshooting Area to Check Explanation BOOTP is in your system’s /etc/services file BOOTP must be an uncommented line in /etc/services. The EPS is in the loadhost’s /etc/hosts file The EPS must be in this file for the host to answer a BOOTP or TFTP request.
Troubleshooting Printing Problems B.5 Printing Problems Table B-6: General Printing Problems Area to Check Explanation Physical connections To test a non-PostScript printer, use the Test Port EPS Count 100 command. This command will send 100 lines of test data out the parallel port so you can see if the printer is receiving data.
Entering Commands at the Boot Prompt Troubleshooting Table B-7: PostScript Troubleshooting, cont. Area to Check Explanation Service Characteristics Issue the Show Service Characteristics command. If the service rating is zero, the parallel port is in use. Verify that the PostScript characteristic and appropriate protocols have been enabled on the service. Port Counters If PostScript jobs appear to print but nothing comes out of the printer, verify the amount of data sent from the host.
Troubleshooting Entering Commands at the Boot Prompt A series of commands called Boot Configuration Program (BCP) commands can be entered at the Boot> prompt to configure the EPS. These commands are a subset of the entire EPS command set. For example, a typical TCP/IP configuration might use the following commands: Figure B-1: BCP Command Examples Boot> Set IPADDRESS 192.0.1.229 Boot> Set SOFTWARE /tftpboot/EPS.SYS Boot> Set LOADHOST 192.0.1.188 Boot> Set SECONDARY 192.0.1.
Entering Commands at the Boot Prompt Set Hardware xx-xx-xx Troubleshooting Specifies the last three numbers of the server’s Ethernet address. The first three numbers will be supplied automatically. The Ethernet address should have been set at the factory. Setting an incorrect address could cause serious network problems. Set IPAddress ip_address Specifies this server’s IP address. Uses the standard numeric format. Set Loadhost ip_address Specifies the host to attempt to load the file from.
C: Pinouts C.1 Ethernet Connector Figure C-1: RJ45 Ethernet Connector 12345678 1 2 3 6 TX+ TXRX+ RX- C.2 Parallel Connectors Lantronix uses standard Centronics parallel connectors. For optimum performance of your EPS, Lantronix recommends the use of high quality parallel cables. Choose one of the following: ◆ A Lantronix parallel port cable, part number #500-011 (6 feet). ◆ Any other brand of IEEE Std. 1284-1994 compliant cable.
D: Updating Software D.1 Obtaining Software Current software files (EPS.SYS) are available on the distribution CD. You can obtain software updates and release notes for the EPS from the Lantronix World Wide Web site (www.lantronix.com), or by using anonymous FTP through the Internet (ftp.lantronix.com). D.1.1 Via the Web The latest version of EPS.SYS can be downloaded from the Lantronix Web site. At the time of this writing, the exact location of the files on the re-designed site was unkown.
Reloading Software Updating Software D.2 Reloading Software The EPS stores software in Flash ROM to control the initialization process, operation, and command processing. The contents of Flash ROM can be updated by downloading a new version of the operational software via NetWare, TCP/IP, or MOP. Regardless of which protocol is used to update Flash ROM, the following points are important: ◆ The Flash ROM software file name, EPS.SYS, should not be changed.
Updating Software Reloading Software To manually configure the EPS IP parameters for software reload, use the following commands. Figure D-2: Configuring TCP/IP Reload Local> SET PRIVILEGED Password> SYSTEM (not echoed) Local>> DEFINE SERVER IPADDRESS nnn.nnn.nnn.nnn Local>> DEFINE SERVER SOFTWARE “/tftpboot/EPS.SYS” Local>> DEFINE SERVER LOADHOST nnn.nnn.nnn.
Troubleshooting Flash ROM Updates Updating Software D.3 Troubleshooting Flash ROM Updates Many of the problems that occur when updating the Flash ROM can be solved by completing the following steps: Table D-1: Flash ROM Troubleshooting Protocol Area to Check NetWare Ensure the file is in the login directory. Since the EPS cannot actually log into the file server, it has very limited access to the server directories. TFTP Check the file and directory permissions.
E: Specifications E.1 Power Information E.1.1 Power Requirements Voltage: 110 V AC US, 220 V AC International Frequency: 47-63 Hz Operating Current: 0.8 Amp (maximum) Power Consumption: 25 Watts Fuse Rating 1.6A, 250 Volts E.1.2 Power Supply Cord Cord type: 3 conductors, 1.0 mm2 minimum conductor size (approximately 18 AWG) Rated for: 250 Volts AC, 10 Amps Length: 3.0 meters E.2 Environmental Limitations E.2.
Environmental Limitations Specifications E.2.2 Altitude Operating maximum: 2.4 km (8,000 ft) Storage maximum: 9.1 km (30,000 ft) If operating the EPS above 2.4 km (8000 ft.), decrease the operating temperature rating by 1° F for each 1000 ft. E.2.
F: Frequently-used Commands This appendix lists some of the most frequently-used commands of the Ethernet Print Server command set. More information about the command set, including additional options, can be found in the Print Server Reference Manual located on the CD-ROM. F.1 Conventions Please note the following before continuing: ◆ Commands are divided into Server (general), Port, and Protocol sections. Within each section, commands are listed alphabetically.
Server Commands Frequently-used Commands F.2 Server Commands Table F-1: Frequently-used Server Commands Command Option(s) Description CONNECT option servicename Makes a connection to a LAT service. LOCAL num Makes a connection to the specified local port. RLOGIN host Makes an Rlogin connection to the specified host (text name or numeric IP address). TCP host Makes a raw TCP connection to the specified host (text name or numeric IP address).
Frequently-used Commands Server Commands Table F-1: Frequently-used Server Commands, cont. Command Option(s) Description DEFINE SERVER NETWARE LOADHOST server Specifies the NetWare host from which the EPS requests its run-time code. Enter a file server name of up to 11 characters. DEFINE SERVER PRIVILEGED PASSWORD Sets a new password that will be required for privileged user status. You will be prompted for the new password (up to 6 alphanumeric characters, case-insensitive).
Server Commands Frequently-used Commands Table F-1: Frequently-used Server Commands, cont. Command Option(s) Description DEFINE SERVICE “name” option DLC {EN/DIS} Specifies which service will handle print requests from DLC hosts. DLC can be enabled on one service per EPS. BANNER {EN/DIS} When Enabled, causes the EPS to print a banner page before jobs. BINARY {EN/DIS} When Enabled, the EPS will not process data passed through the service.
Frequently-used Commands Port Commands Table F-1: Frequently-used Server Commands, cont. Command Option(s) Description LOGOUT option Logs out the current port (the port that issued the command). PORT num Logs out the specified port. LOCAL Removes the definitions of all local services. “service” Removes the definition of the specified service. PURGE SERVICE option SET PRIVILEGED Enters privileged mode, provided the user enters the proper privileged password when prompted.
Port Commands Frequently-used Commands Table F-2: Port Commands, cont. Command Option(s) Description DEFINE PORT n BITRONICS {EN/DIS} When Enabled, ensures bidirectional functioning of the parallel port. The attached printer must also support Bitronics mode. DEFINE PORT n CHARACTER size Toggles the port between 7-bit and 8-bit characters (the default). Enter either 7 or 8. DEFINE PORT n DSRLOGOUT {EN/DIS} When Enabled, the port will be logged out automatically whenever DSR is deasserted.
Frequently-used Commands Protocol Commands F.4 Protocol Commands In the following table, PROTO is an abbreviation for the optional keyword PROTOCOL. Table F-3: Protocol Commands Command Option(s) Description DEFINE PROTO APPLETALK option {EN/DIS} Enables or Disables the AppleTalk protocol for the EPS. ZONE newzone Places the EPS in a zone other than the default. {EN/DIS} Enables or Disables the TCP/IP protocol for the EPS. GATEWAY ipaddr See DEFINE SERVER GATEWAY ipaddr.
Protocol Commands Frequently-used Commands Table F-3: Protocol Commands, cont. Command Option(s) Description DEFINE PROTO NETWARE ENCAPSULATION option {EN/DIS} NATIVE Configures the EPS to use the “native mode” frame format. ETHER_II Configures the EPS to use Ethernet v2 frame format. 802_2 Configures the EPS to use 802.2 frame format with NetWare SAPs. SNAP Configures the EPS to use 802.2 frame format with SNAP SAPs.
Warranty Statement Lantronix warrants for a period of FIVE years from the date of shipment that each EPS1 and EPS2 Ethernet Print Server supplied shall be free from defects in material and workmanship. During this period, if the customer experiences difficulties with a product and is unable to resolve the problem by phone with Lantronix Technical Support, a Return Material Authorization (RMA) will be issued.
Declaration of Conformity (according to ISO/IEC Guide 22 and EN 45014) Manufacturer’s Name & Address: Lantronix 15353 Barranca Parkway, Irvine, CA 92618 USA Declares that the product: Product Name: Model Name/Number: Print Server EPS1 EPS2 Conforms to the following standards or other normative documents: Safety: Electromagnetic Emissions: Electromagetic Immunity: EN60950:1988+A1, A2 EN55022: 1998 (CISPR 22, Class A: 1993, A1: 1995, A2: 1996) IEC 1000-3-2/A14: 2000 IEC 1000-3-3: 1994 EN55024: 1998 Info
Index Symbols /etc/hosts 4-2 Numerics 10BASE-T 2-1, 2-4 A Access list, NetWare 5-2 ACT LED B-1 AppleTalk 3-2, 7-1–7-2 Chooser 7-1 Configuration 7-1 Router 7-1 Troubleshooting 7-2 Zones 7-1, 7-2 Application port, LAT 6-1 ARP table 4-2 AUI 2-1, 2-4 B Back panel 2-1 Banner 4-3, 4-11 BCP (Boot Configuration Program) B-7 Bindery 5-1 Bitmap graphics troubleshooting B-6 Bitronics 3-2, 7-1 Boot prompt B-1, B-6 BOOT sequence 2-4 BOOTP 4-1, 4-3, 5-5, D-2 Troubleshooting B-4 Bottom label 2-1 C Cables C-1 Centroni
F Index 1 F Factory defaults B-7 Filters, input/output 4-4 Flash B-1, D-2 Troubleshooting D-4 Updates B-2, D-2 Flash ROM B-3 Reloading B-7 Flush NVR B-7 Front panel 2-1 FTP 3-1, D-1 H Hardware address 4-2, B-4, B-8 I Incoming logins 3-1 Installation 2-3 Introduction 1-1 IP address 3-1, 4-1, 4-7, 5-1, 6-1, 71, 8-1, B-1, B-4 Configuring 4-1, B-8 Configuring via BOOTP 4-3 Configuring via command line 4-3 Configuring via DHCP 4-3 Configuring via Ping 4-1 Configuring via RARP 4-3 IPX (NetWare) 5-1–5-4 J Ja
Index N Named pipe interface 4-4 Nameserver 4-2 NDPS 5-1 NDS 5-1 Directory service context 5-2 Directory service tree 5-2 License 5-1, 5-2 NetWare 3-2, 5-1–5-4 Access list 5-2 Administrator 5-1, 5-2 Bindery 5-1 NDS 5-1, 5-2 PCONSOLE 5-3 Reloading software D-3 Troubleshooting 5-4 NVRAM B-7 O OK LED 2-2 P Parallel port 2-1, C-1 Service 3-2 Passwords Login 3-1, 3-2 Privileged 3-1, F-1 PCONSOLE 5-1, 5-3 Ping 4-1 Pinouts C-1 Ports Parallel 2-1, C-1 Serial 2-1 PostScript 7-1 Troubleshooting B-5 Power Connector
S Index TCP/IP D-2 Remote console logins 3-1 Remote printer 3-2 Remote queue 3-2 Reset/Test button 2-4 Restoring defaults B-7 RJ45 2-1, C-1 RTEL 4-3, 4-4, 4-11 T TCP/IP 3-2, 4-1–4-12, 8-1, B-1 Reloading software D-2 Telnet 3-2, 4-2, 4-12 Test page 2-4 Test/Reset button 2-4 TFTP D-2 Top panel 2-2 Troubleshooting B-1–B-8 AppleTalk 7-2 Bitmap graphics B-6 BOOTP B-4 DHCP B-3 Flash (software) updates D-4 LAT 6-2 NetWare 5-4 PostScript B-5 Power-up B-1, B-2 Printing B-5 RARP B-4 Unix 4-12 S SAM 4-9 Serial LED
