User Manual

ManualsBrandsLanParte ManualsStabilizersDetachable Wired Control 3-Axis Gimbal for Smartphones

LA3D-S2

DETACHABLE WIRED CONTROL GIMBAL

3-Axis Handheld Gimbal for Smartphone

USER MANUAL

HONGKONG LANPARTE TECHNOLOGY LIMITED

Email:info@lanparte.com

Tel:+86-0769-81889368

Fax:+86-0769-85841828

ADD:NO.39, 2nd Xin’an road

Changan Town, Dongguan, Guangdong, China

www.lanparte.com LA3D-S2 manual

Summary of content (8 pages)

PAGE 1
DETACHABLE WIRED CONTROL GIMBAL USER MANUAL 3-Axis Handheld Gimbal for Smartphone Contact us for further Questions! www.lanparte.com LA3D-S2 manual HONGKONG LANPARTE TECHNOLOGY LIMITED Email:info@lanparte.com Tel:+86-0769-81889368 Fax:+86-0769-85841828 ADD:NO.
PAGE 2
1 Appearance and Design Attention! Make sure to attach smartphone before turning on power.
PAGE 3
2 Item list Serial No. 3 Gimbal Installation Item Name QTY 3.1 Gimbal Installation 3-Axis handheld gimbal head Gimbal handle 18350 Li-ion battery Handle extender Wired control cable(1.5m) Battery charger Micro USB cable (For battery charger) Smartphone clamp Counterweight Turn counter clockwise to open Turn clockwise to lock 3 Align the contacts on the handle and gimbal head and turn clockwise.
PAGE 4
Operation 3.2 Battery Instructions Battery installation: Unscrew the battery compartment cap and install two 18350 batteries; or add the handle extender and install two 18650 batteries (install the positive end first) 4.1 Balance adjustment A. Open the smartphone clamp and insert the smartphone *Please note that the nominal Voltage of the gimbal is 7.4V Each 18350 & 18650 battery is 3.7V. Therefore, the gimbal MUST operate on a maximum of TWO batteries.
PAGE 5
C. Slide the smartphone left to right in the clamp to achieve horizontal balance. For smaller smartphones like the iPhone 6, add the counterweight. For other smartphone and aftermarket lens or mic combinations, use counterweights as necessary. 4.2 Powering on/mode switch A. Before turn on the power, make sure the white line points in the middle position Zero point D. Loosen the silver adjustment screw, then slide the smartphone forwards or backwards until vertical balance is achieved.
PAGE 6
4.3 Portrait vertical mode: 5 Mode Switching Double-tap the POWER button to enter portrait mode. Repeat the double-tap to switch back to landscape mode. Modes Control Button (in Operation mode) How to activate Mode Indicator Direction Control Mode1 Mode button Single-tap Green Push the joystick left and right to adjust the Roll. Mode2 Mode button Double-tap Red Push the joystick left and right to adjust the Roll; up and down to adjust the Pitch (Tilt).
PAGE 7
9 Standby Mode Operating mode and Axis status Mode Axis Pitch(Tilt) Roll Yaw(Pan) Mode1 Following Locked Following Mode2 Locked Locked Following Mode2 Locked Locked Locked 7 Power Display Power Indicator Status Indicator Status 75%-100% Light blinks 4 times, 1 sec/time, repeat after 5 sec 50%-75% Light blinks 3 times, 1 sec/time, repeat after 5 sec 25%-50% Light blinks twice,1 sec/time, repeat after 5 sec Below 25% Light blinks continuously.
PAGE 8
12 Optional Accessories Size of Gimbal Wired control Weight:414.5g (w/o battery) Standard 1/4 -20 thread hole on bottom 11 Parameter Item 6.5V - 12.6V Operating current Standard 120mA Pitch angle ± 70 Roll angle ± 35 Yaw angle ± 310 Battery operating time Operating Temperature Net weight Product Dimension Package Dimension 13 Parameter Operating voltage Standard 2h - 10 ~ 40 414.5g(w/o battery and smartphone) 300.4 * 205.4 * 92.