Operators Guide 5613 Copier Reference you r docu ment m an a ge m ent pa r tne r
Paper type: OK Prince Eco G100(55kg), Paper Thickness=80 µm // Pages in book=84 // Print scale=81% Gap (when printed at 81% scale) = Pages in book × Paper thickness / 2 = 3.360000 mm Introduction This manual contains detailed instructions on the operation and maintenance of this machine. To get maximum versatility from this machine all operators should carefully read and follow the instructions in this manual. Please keep this manual in a handy place near the machine.
StellaC-EN-CopyF_V4_FM.book Page i Wednesday, July 4, 2001 11:23 AM Safety Information When using your equipment, the following safety precautions should always be followed. Safety During Operation In this manual, the following important symbols are used: R WARNING: Indicates a potentially hazardous situation which, if instructions are not followed, could result in death or serious injury.
StellaC-EN-CopyF_V4_FM.book Page ii Wednesday, July 4, 2001 11:23 AM R CAUTION: • Protect the equipment from dampness or wet weather, such as rain, snow, and so on. • Unplug the power cord from the wall outlet before you move the equipment. While moving the equipment, you should take care that the power cord will not be damaged under the equipment. • When you disconnect the power plug from the wall outlet, always pull the plug (not the cable).
StellaC-EN-CopyF_V4_FM.book Page iii Wednesday, July 4, 2001 11:23 AM Positions of Labels and Hallmarks for RWARNING and RCAUTION This machine has labels and hallmarks for RWARNING,RCAUTION at the positions shown below. For safety, please follow the instructions and handle the machine as indicated. The inside of the machine becomes very hot. Do not touch the inside. Doing so could result in a burn. A B The anti-condensation heater in the inner lower part of the machine becomes very hot. Do not touch it.
StellaC-EN-CopyF_V4_FM.book Page iv Wednesday, July 4, 2001 11:23 AM How to Read this Manual Symbols In this manual, the following symbols are used: R WARNING: This symbol indicates a potentially hazardous situation that might result in death or serious injury when you misuse the machine without following the instructions under this symbol. Be sure to read the instructions, all of which are described in the Safety Information section.
StellaC-EN-CopyF_V4_FM.book Page v Wednesday, July 4, 2001 11:23 AM Machine Types This machine has two models. Type 2 machine is installed with the fax unit as a standard.
StellaC-EN-CopyF_V4_FM.
StellaC-EN-CopyF_V4_FM.book Page vii Wednesday, July 4, 2001 11:23 AM TABLE OF CONTENTS Guide to Components ................................................................................ 1 Options ........................................................................................................ 3 Control Panel .............................................................................................. 4 Panel Display ................................................................................
StellaC-EN-CopyF_V4_FM.book Page viii Wednesday, July 4, 2001 11:23 AM Other Functions........................................................................................ 31 User Codes .................................................................................................. 31 Auto Start ..................................................................................................... 31 Preset Reduce/Enlarge ............................................................................
StellaC-EN-CopyF_V4_FM.book Page ix Wednesday, July 4, 2001 11:23 AM 6. Specifications Mainframe.................................................................................................. 65 Document Feeder (ADF) (Option for Type 1) ......................................... 68 Paper Tray Unit (Option) ......................................................................... 69 32MB Copier Memory Unit (Option)........................................................ 70 INDEX...........................
StellaC-EN-CopyF_V4_FM.
StellaC-EN-CopyF_V4_FM.book Page 1 Wednesday, July 4, 2001 11:23 AM Guide to Components 1. Exposure glass cover 5. Ventilation hole Lower the exposure glass cover over the original placed on the exposure glass for copying. Prevents overheating. Do not obstruct the ventilation hole by placing or leaning an object near it. If the machine overheats, a fault might occur. 2. Document feeder (ADF) (Option for Type 1) Originals will be fed automatically. 3.
StellaC-EN-CopyF_V4_FM.book Page 2 Wednesday, July 4, 2001 11:23 AM 8. On indicator 11. Front cover This indicator lights up when the operation switch is turned on, and goes off when the switch is turned off. Open to access the inside of the machine. 9. Operation switch 2 12. Paper tray Place paper here. See p.42 “h Loading Paper”. Press this switch to turn the power on (the On indicator lights up). To turn the power off, press this switch again (the On indicator goes off). 13.
StellaC-EN-CopyF_V4_FM.book Page 3 Wednesday, July 4, 2001 11:23 AM Options 1. Document feeder (ADF) (Option for Type 1) 2. Paper tray unit Holds 500 sheets of paper. Originals will be fed automatically. Other options: • 32MB copier memory unit Increases memory capacity.
StellaC-EN-CopyF_V4_FM.book Page 4 Wednesday, July 4, 2001 11:23 AM Control Panel ❖ Copier only ❖ Fax and/or printer installed 1. Indicators for fax mode (Fax in- 6. {Cancel}} key stalled machine only) Press to cancel an operation or return to the previous display. See the Facsimile Reference manual. 2. {Facsimile}} key (Fax installed machine only) Press to use facsimile functions. 3. {Printer}} key (Printer installed machine only) Press to use printer functions. 4.
StellaC-EN-CopyF_V4_FM.book Page 5 Wednesday, July 4, 2001 11:23 AM 11. {Clear/Stop}} key 18. {Select Paper Tray}} key While entering numbers, press to cancel a number you have entered. While copying, press to stop copying. Press to select the paper tray. 19. {Zoom}} key 12. {Clear Modes}} key Changes the reproduction ratio in 1% steps. Press to clear the previously entered copy job settings. 20. {Reduce/Enlarge}} key 13. On indicator Press to make reduced or enlarged copies. See p.
StellaC-EN-CopyF_V4_FM.book Page 6 Wednesday, July 4, 2001 11:23 AM Panel Display The panel display shows the status of the machine, error messages, and function menus. Important ❒ Do not apply a strong shock or force of about 30N (about 3kgf) or more to the panel display. Otherwise, the display might be damaged. Note ❒ The machine is in Copy mode when turned on. This can be changed. See “Settings You Can Change with the User Tools” in the System Settings manual.
StellaC-EN-CopyF_V4_FM.book Page 7 Wednesday, July 4, 2001 11:23 AM 1. Basics Turning On the Power To turn the machine on, press the operation switch. Note ❒ This machine automatically enters Energy Saver mode or turns itself off if you do not use the machine for a while. See “6. Auto Off Timer” in the System Settings manual. - Power switches This machine has two power switches. ❖ Operation switch (right side of the control panel) Press this switch to activate the machine.
StellaC-EN-CopyF_V4_FM.book Page 8 Wednesday, July 4, 2001 11:23 AM Basics Starting the Machine A Press the operation switch to make the On indicator go on. 1 The display panel will come on. Note ❒ If the power is not turned on when the operation switch is pressed, check if the main power switch is on. If off, turn it on. ❒ During the warm-up period (less than 20 seconds), you can use the Auto Start function. See p.31 “Auto Start”.
StellaC-EN-CopyF_V4_FM.book Page 9 Wednesday, July 4, 2001 11:23 AM Changing Modes Changing Modes You can use this machine not only as a copier, but optionally as a fax machine or a printer as well. (Type 2 machine is installed with the fax function as the standard.) Press the {Copy} } key to use copy functions, or press the {Facsimile} } key to use facsimile functions. If the display shows a mode other than copy mode, press the {Copy} } key to switch to copy mode.
StellaC-EN-CopyF_V4_FM.
StellaC-EN-CopyF_V4_FM.book Page 11 Wednesday, July 4, 2001 11:23 AM Originals Original Sizes and Scanning Area/Missing Image Area ❖ Exposure glass 1 ❖ Document feeder (ADF) Limitation ❒ Even if you correctly place originals in the document feeder (ADF) or on the exposure glass, margins (about 4mm, 0.2") on all four sides might not be copied.
StellaC-EN-CopyF_V4_FM.book Page 12 Wednesday, July 4, 2001 11:23 AM Basics Copy Paper Recommended Paper Sizes and Types 1 The following limitations apply to each tray: Paper Tray Paper sizes Paper weight Paper capacity A4L, A5K, 81/2" × 11"L, 51/2" × 81/2"K 60 – 90g/m2, 16 – 24 lb 250 sheets *1 60 – 90g/m2, 16 – 24 lb 500 sheets *1 Note ❒ You can specify the paper size with the user tools. See p.51 “Selecting the Paper Size with the User Tools”.
StellaC-EN-CopyF_V4_FM.book Page 13 Wednesday, July 4, 2001 11:23 AM Copy Paper Important ❒ Use of damp or curled paper may cause a misfeed. If a misfeed occurs, try turning over the paper stack in the paper tray. If there is no improvement, change to copy paper with less curl. 1 Note ❒ Postcards should be fed from the bypass tray. ❒ When printing on envelopes, note the following: • Load envelopes with the copy side face down on the bypass tray. • Check that envelope flaps are securely folded up.
StellaC-EN-CopyF_V4_FM.book Page 14 Wednesday, July 4, 2001 11:23 AM Basics Note ❒ Do not use any of the following kinds of paper or a misfeed might occur. • Bent, folded, or creased paper • Damp paper • Torn paper • Slippery paper • Perforated paper • Rough paper • Thin paper that has low stiffness • Paper with much paper dust on its surface ❒ If you make copies on rough grain paper, the copy image might be blurred. ❒ Do not use envelopes in the following conditions.
StellaC-EN-CopyF_V4_FM.book Page 15 Wednesday, July 4, 2001 11:23 AM Toner Toner Handling Toner 1 R WARNING: • Do not incinerate used toner or toner containers. Toner dust might ignite when exposed to an open flame. Dispose of used toner containers in accordance with local regulations for plastics. R CAUTION: • Keep toner (used or unused) and toner containers out of reach of children.
StellaC-EN-CopyF_V4_FM.
StellaC-EN-CopyF_V4_FM.book Page 17 Wednesday, July 4, 2001 11:23 AM 2. Copying Basic Procedure A Make sure that the machine is in Copy mode. Note ❒ If not, press the {Copy} } key. B If the machine is set for User Code, enter the code with the number keys, and then press the {OK} } key. See p.31 “User Codes”. C Make sure that there are no previous settings remaining. Note ❒ To clear settings, press the {Clear Modes} } key. Note ❒ The maximum copy quantity can be set between 1 and 99 (default: 99).
StellaC-EN-CopyF_V4_FM.book Page 18 Wednesday, July 4, 2001 11:23 AM Copying - Auto Off The machine turns itself off automatically after your job is finished, after a certain period of time. This function is called “Auto Off”. 2 Note ❒ How to exit Auto Off mode: • Turn on the operation switch • Place an original in the document feeder (ADF) • Lift and lower the exposure glass cover ❒ You can change the Auto Off time. See “6. Auto Off Timer” in the System Settings manual.
StellaC-EN-CopyF_V4_FM.book Page 19 Wednesday, July 4, 2001 11:23 AM Placing Originals Placing Originals Limitation ❒ Place originals after correction fluid and ink has completely dried. Not taking this precaution could mark the exposure glass and cause marks to be copied. Placing Originals on the Exposure Glass Note ❒ Basically, the originals should be aligned to the rear left corner. However, some copy functions may produce different results depending on the direction of the originals.
StellaC-EN-CopyF_V4_FM.book Page 20 Wednesday, July 4, 2001 11:23 AM Copying Loading Originals in the Document Feeder (ADF) Note ❒ The original might become dirty if it is written with a pencil or similar tools. ❒ Do not place any foreign objects on the document feeder (ADF) or cover it with your hand. 2 Note ❒ Do not stack originals above the limit mark. ❒ To avoid a multi-sheet feed, shuffle the originals before setting them in the document feeder (ADF).
StellaC-EN-CopyF_V4_FM.book Page 21 Wednesday, July 4, 2001 11:23 AM Placing Originals C Make sure that "Standard Size" is selected, and then press the {OK} } key. Note ❒ If not, press the 0 or 1 key to select it. D Press the 0 or 1 key to select original size, and then press the {OK} } key. E Press the {Select Paper Tray}} key to select your desired tray.
StellaC-EN-CopyF_V4_FM.book Page 22 Wednesday, July 4, 2001 11:23 AM Copying C Press the 0 or 1 key to select "3. Original Size", and then press the {OK} } key. 2 Note ❒ You can also enter this mode by pressing the {R/#} } key. D Press the 0 or 1 key to select "Custom Size", and then press the {OK} } key. E Enter the horizontal size of the original with the number keys, and then press the {OK} } key. F Enter the vertical size of the original with the number keys, and then press the {OK} } key.
StellaC-EN-CopyF_V4_FM.book Page 23 Wednesday, July 4, 2001 11:23 AM Basic Functions Basic Functions Note ❒ You can select functions to be activated when System Reset is turned on, when Energy Saver is turned off, or after the machine is powered on. See p.56 “Settings You Can Change with the User Tools”. ❒ You can change default settings for basic functions. See p.56 “Settings You Can Change with the User Tools”. Adjusting Copy Image Density You can adjust the copy image density to match your originals.
StellaC-EN-CopyF_V4_FM.book Page 24 Wednesday, July 4, 2001 11:23 AM Copying Selecting Copy Paper You can manually select the paper tray for the paper size you wish to use. A Select the paper tray or bypass tray by pressing the {Select Paper Tray} } key.
StellaC-EN-CopyF_V4_FM.book Page 25 Wednesday, July 4, 2001 11:23 AM Sort Sort The optional 32MB copier memory unit is required to use this function. The machine can scan your originals into memory and automatically sort the copies. Limitation ❒ The maximum paper length for the sort function is 356 mm. Sort 2 Copies can be assembled as sets in sequential order. ❖ Sort Note ❒ The maximum tray capacity is as follows. When the number of copies exceeds the tray capacity, remove copies from the tray.
StellaC-EN-CopyF_V4_FM.book Page 26 Wednesday, July 4, 2001 11:23 AM Copying D Enter the number of copy sets with the number keys. Note ❒ The maximum number of sets is 99. You can change the default number with “1. Max. Copy Q'ty” in the copier features. See p.56 “Settings You Can Change with the User Tools”. ❒ To change the number entered, press the { Clear/Stop} } key and enter the new number. 2 E Place your originals.
StellaC-EN-CopyF_V4_FM.book Page 27 Wednesday, July 4, 2001 11:23 AM Copying from the Bypass Tray Copying from the Bypass Tray Use the bypass tray to copy onto OHP transparencies, adhesive labels, translucent paper, postcards, envelopes, and copy paper that cannot be set in the paper tray. B Push up the paper guide release lever. 2 Note ❒ If you do not use standard size copy paper, you should enter vertical and horizontal dimensions.
StellaC-EN-CopyF_V4_FM.book Page 28 Wednesday, July 4, 2001 11:23 AM Copying Note ❒ Set the direction of the copy paper to L. ❒ Swing out the extender to support paper sizes larger than A4L, 81/2" × 14"L. ❒ Fan paper to get air between the sheets and avoid a multi-sheet feed. 2 Reference For details about how to set the copy paper, see p.28 “When copying onto OHP transparencies”, p.29 “When copying onto standard size pap er ”, p.29 “When copying onto custom size copy paper” or p.
StellaC-EN-CopyF_V4_FM.book Page 29 Wednesday, July 4, 2001 11:23 AM Copying from the Bypass Tray F Gently insert the OHP transparencies face down and adjust the paper guide. B Make sure that "Standard Size" is selected, and then press the {OK} } key. 2 Note ❒ If not, press the 0 or 1 key to select it. C Press the 0 or 1 key to select pa- per size, and then press the {OK} } key. Important ❒ The side of OHP transparencies that is copied is fixed.
StellaC-EN-CopyF_V4_FM.book Page 30 Wednesday, July 4, 2001 11:23 AM Copying C Enter the horizontal size of the paper with the number keys, and then press the {OK} } key. 2 Note ❒ To change the number entered, press the {Clear/Stop} } key, and then enter the new number. D Enter the vertical size of the paper When copying onto envelopes Note ❒ Set the direction of the envelope to L Reference For details about envelopes, see p.12 “Copy Paper” A Press the {User Tools/Counter}} key.
StellaC-EN-CopyF_V4_FM.book Page 31 Wednesday, July 4, 2001 11:23 AM Other Functions Other Functions User Codes When user codes are set, operators must enter their user codes before the machine can be operated. The machine keeps count of the number of copies made under each user code. Note ❒ When user codes are set, the machine will prompt you for your user code after the power switch is turned on or Copy Reset Timer comes into effect.
StellaC-EN-CopyF_V4_FM.book Page 32 Wednesday, July 4, 2001 11:23 AM Copying Preset Reduce/Enlarge You can select a preset ratio for copying. 2 Note ❒ You can select one of 5 preset ratios (2 enlargement ratios, 3 reduction ratios). ❖ Inch version Ratio (%) Original → Copy paper size 155 (enlarge area by 2) 51/2" × 81/2"→81/2" × 14" 129 51/2" × 81/2"→81/2" × 11" 100 Full Size 93 A little reduced.
StellaC-EN-CopyF_V4_FM.book Page 33 Wednesday, July 4, 2001 11:23 AM Preset Reduce/Enlarge D Place your originals, and then press the {Start} } key. Note ❒ When the copy paper size and the original size differ, set the original size. See p.
StellaC-EN-CopyF_V4_FM.book Page 34 Wednesday, July 4, 2001 11:23 AM Copying Zoom You can change the reproduction ratio in 1% steps. B Enter the ratio. When using the 0 or 1 key 2 A Enter the desired reproduction ratios with the 0 or 1 key. Note ❒ You can change the reproduction ratio from 50–200%. ❒ You can select a ratio regardless of the size of an original or copy paper. With some ratios, parts of the image might not be copied or margins will appear on copies.
StellaC-EN-CopyF_V4_FM.book Page 35 Wednesday, July 4, 2001 11:23 AM Combine Combine Use this feature to combine two original images onto one page. 1 2 ❖ Portrait (K K) originals 2 1 2 Combine1 ❖ Landscape (L L) originals Limitation ❒ The machine cannot copy originals different in size and direction. Note ❒ A5, 51/2" × 81/2"K copy paper cannot be combined. ❒ The number of originals copied (combined) can be 2. ❒ In this mode, the machine selects the reproduction ratio automatically.
StellaC-EN-CopyF_V4_FM.book Page 36 Wednesday, July 4, 2001 11:23 AM Copying C Select “ ” with the 0 or 1 key, and then press the {OK} } key. Note ❒ You can specify the orientation of originals. See “5. Orig. Orientation” in the Copier Features in p.56 “Settings You Can Change with the User Tools” 2 D Press the {Select Paper Tray}} key to select the copy paper. E Place your originals. Note ❒ Set the direction of the original to L.
StellaC-EN-CopyF_V4_FM.book Page 37 Wednesday, July 4, 2001 11:23 AM Combination Chart Combination Chart The combination chart given below shows which modes can be used together. When you read the chart, please refer to the following table. ✩ means that these modes can be used together. → means that these modes cannot be used together. The mode after you select will be the mode you're working in. × means that these modes cannot be used together.
StellaC-EN-CopyF_V4_FM.
StellaC-EN-CopyF_V4_FM.book Page 39 Wednesday, July 4, 2001 11:23 AM 3. Troubleshooting Machine Operation Problems General Machine's Condition Problem/Cause Action The machine instructs you to wait. The machine is warming up. Wait for the machine to warmup. Reference You can use Auto Start mode during the warm-up period. See p.31 “Auto Start”. You cannot enter the desired copy set number. The number of copies exceeds the maximum copy quantity.
StellaC-EN-CopyF_V4_FM.book Page 40 Wednesday, July 4, 2001 11:23 AM Troubleshooting Cannot Make Clear Copies 3 Problem Cause Copies appear dirty. The image density is too dark. Adjust the image density. See p.23 “Adjusting Copy Image Density”. Action The reverse side of an original image is copied. The image density is too dark. Adjust the image density. See p.23 “Adjusting Copy Image Density”. A shadow appears on copies if you use the pasted originals. The image density is too dark.
StellaC-EN-CopyF_V4_FM.book Page 41 Wednesday, July 4, 2001 11:23 AM Cannot Make Desired Copies Cannot Make Desired Copies Problem Cause Action Misfeeds occur frequently. Copy paper size setting is not correct. Set the proper paper size. See p.48 “Changing the Paper Size” or p.27 “Copying from the Bypass Tray”. You cannot combine several functions. Selected functions cannot be used together. Refer to the combination chart. See p.37 “Combination Chart”.
StellaC-EN-CopyF_V4_FM.book Page 42 Wednesday, July 4, 2001 11:23 AM Troubleshooting h Loading Paper Note ❒ If you want to change the paper size, see p.48 “Changing the Paper Size”. Reference Regarding paper types and sizes that can be used, see p.12 “Copy Paper”. 3 A Make sure that the paper tray is not being used. B Pull out the paper tray until it stops. C Push the metal plate down, and then square the paper and load it in the tray. Note ❒ Shuffle the paper before setting it in the tray.
StellaC-EN-CopyF_V4_FM.book Page 43 Wednesday, July 4, 2001 11:23 AM h Loading Paper Note ❒ Shuffle the paper before loading it in the tray. ❒ If the paper is curled, load the paper up side down. E Readjust the back fence and side fences. Important ❒ When loading small quantities of copy paper, be careful not to squeeze in the side fence too much or paper will not be fed properly. F Push 3 the paper tray in until it stops.
StellaC-EN-CopyF_V4_FM.book Page 44 Wednesday, July 4, 2001 11:23 AM Troubleshooting h Changing the Toner Cartridge When h is displayed, it is time to supply toner. R WARNING: • Do not incinerate used toner or toner containers. Toner dust might ignite when exposed to an open flame. Dispose of used toner containers in accordance with local regulations for plastics. R CAUTION: • Keep toner (used or unused) and toner containers out of reach of children.
StellaC-EN-CopyF_V4_FM.book Page 45 Wednesday, July 4, 2001 11:23 AM h Changing the Toner Cartridge • Press the Toner Cartridge backward to raise its head, and then gently pull out the bottle. • Hold the new bottle horizontally, and then shake it 5 or 6 times. 3 Note ❒ Do not remove the black cap when shaking. • Remove the black cap. Note ❒ Do not remove the inner cap. • Put the Toner Cartridge on the holder, and then press its head forward. • Push the holder in until it clicks.
StellaC-EN-CopyF_V4_FM.book Page 46 Wednesday, July 4, 2001 11:23 AM Troubleshooting h Clearing Misfeeds 3 R CAUTION: • The fusing section of this equipment might be very hot. You should be very careful that you don't touch this section when removing the misfed paper. Important ❒ When clearing misfeeds, do not turn off the power switch. If you do, your copy settings are cleared. ❒ To prevent misfeeds, do not leave any torn scraps of paper within the machine.
StellaC-EN-CopyF_V4_FM.
StellaC-EN-CopyF_V4_FM.book Page 48 Wednesday, July 4, 2001 11:23 AM Troubleshooting Changing the Paper Size Important ❒ Select the paper size with the user tools, or misfeeds might occur. Reference For paper sizes, weight, and capacity that can be loaded in each tray, see p.12 “Copy Paper”. 3 Note ❒ When you load A4L copy paper, place the back fence in the corner pocket on the left. Changing the Paper Size in the Paper Tray A Make sure that the paper tray is not being used.
StellaC-EN-CopyF_V4_FM.book Page 49 Wednesday, July 4, 2001 11:23 AM Changing the Paper Size F Square the paper and load it in the tray. Changing the Paper Size in the Optional Paper tray unit A Make sure that the paper tray is not being used. B Pull out the paper tray until it stops. Note ❒ Remove any remaining copy paper. Important ❒ Do not stack paper over the limit mark. 3 C Adjust the back fence. G Adjust the side and back fences to the new paper size.
StellaC-EN-CopyF_V4_FM.book Page 50 Wednesday, July 4, 2001 11:23 AM Troubleshooting D While pressing the release lever, adjust the side fences. F Adjust the side and back fences to the new paper size. 3 E Push the metal plate down, and then square the paper and load it in the tray. Important ❒ When loading small quantities of copy paper, be careful not to squeeze in the side fence too much or paper will not be fed properly. G Push the paper tray in until it stops.
StellaC-EN-CopyF_V4_FM.book Page 51 Wednesday, July 4, 2001 11:23 AM Changing the Paper Size Selecting the Paper Size with the User Tools A Press the {User Tools/Counter}} key. E If you have selected "3. Bypass" on step D, select "Standard Size" or "Custom Size", and then press the {OK} } key. F Select the desired paper size.
StellaC-EN-CopyF_V4_FM.
StellaC-EN-CopyF_V4_FM.book Page 53 Wednesday, July 4, 2001 11:23 AM 4. User Tools (Copier Features) Accessing the User Tools (Copier Features) This section is for the key operators in charge of this machine. The user tools allow you to change or set the machine's default settings. C Press the 0 or 1 key until de- sired User Tools menu is displayed, and then press the {OK} } key. Preparation Always exit the user tools when you have finished.
StellaC-EN-CopyF_V4_FM.book Page 54 Wednesday, July 4, 2001 11:23 AM User Tools (Copier Features) Exiting the User Tools A Press the {User Tools/Counter}} key. 4 Note ❒ You can exit the User Tools mode by pressing the {Cancel} } key. ❒ If you want to return to the previous mode (copy or facsimile), press the { User Tools/Counter} } key.
StellaC-EN-CopyF_V4_FM.
StellaC-EN-CopyF_V4_FM.book Page 56 Wednesday, July 4, 2001 11:23 AM User Tools (Copier Features) Settings You Can Change with the User Tools Reference For details about how to access the user tools, see p.53 “Accessing the User Tools (Copier Features)”. Copier Features 4 Menu Description 1. Maximum Copy Quantity (1. Max. Copy Q'ty) The maximum copy quantity can be set between 1 and 99. Note ❒ Default: 99 2.
StellaC-EN-CopyF_V4_FM.book Page 57 Wednesday, July 4, 2001 11:23 AM Settings You Can Change with the User Tools Menu Description 3. Set Ratio Select which Reduce, Enlarge or Input Ratio is shown on the panel display with priority when the {Reduce/Enlarge} } key is pressed. Note ❒ Default: • Ratio 1: 65% 81/2" × 11"→51/2" × 81/2" • Ratio 2: 78% 81/2" × 14"→81/2" × 11" • Ratio 3: 93% • Ratio 4: 129% 51/2" × 81/2"→81/2" × 11" • Ratio 5: 155% 51/2" × 81/2"→81/2" × 14" 4.
StellaC-EN-CopyF_V4_FM.book Page 58 Wednesday, July 4, 2001 11:23 AM User Tools (Copier Features) Menu Description 5. Clear all User Codes (5. Clr All User Codes) You can clear all user codes. Note ❒ The number of copies made under the old code is added to that made under the new user code. ❒ The number of copies made under the deleted code is also deleted. 6. Reset All Counters You can reset each user code's counter to 0. 7. Program User Code You can register user codes.
StellaC-EN-CopyF_V4_FM.book Page 59 Wednesday, July 4, 2001 11:23 AM 5. Remarks Do's and Don'ts R CAUTION: • Unplug the power cord from the wall outlet before you move the equipment. While moving the equipment, you should take care that the power cord will not be damaged under the equipment. Important ❒ Make sure the remaining memory space is 100%, before you unplug the power cord. ❒ While the machine is unplugged, you can neither send nor receive a fax.
StellaC-EN-CopyF_V4_FM.book Page 60 Wednesday, July 4, 2001 11:23 AM Remarks Where to Put Your Machine Machine Environment Your machine's location should be carefully chosen because environmental conditions greatly affect its performance. Optimum environmental conditions R CAUTION: • Keep the equipment away from humidity and dust. Otherwise a fire or an electric shock might occur. • Do not place the equipment on an unstable or tilted surface. If it topples over, it could cause injury.
StellaC-EN-CopyF_V4_FM.book Page 61 Wednesday, July 4, 2001 11:23 AM Where to Put Your Machine Power Connection R WARNING: • Only connect the machine to the power source described on the inside front cover of this manual. Connect the power cord directly into a wall outlet and do not use an extension cord. • Do not damage, break or make any modifications to the power cord. Do not place heavy objects on it. Do not pull it hard nor bend it more than necessary.
StellaC-EN-CopyF_V4_FM.book Page 62 Wednesday, July 4, 2001 11:23 AM Remarks Access to Machine Place the machine near the power source, providing clearance as shown. 1. Rear: more than 1cm (0.4") 2. Right: more than 1cm (0.4") 5 3. Front: more than 75cm (29.6") 4. Left: more than 1cm (0.4") Note ❒ For information about required space when options are installed, please contact your service representative.
StellaC-EN-CopyF_V4_FM.book Page 63 Wednesday, July 4, 2001 11:23 AM Maintaining Your Machine Maintaining Your Machine If the exposure glass, exposure glass cover or document feeder (ADF) white sheet is dirty, clean them if you find them dirty. Cleaning the Exposure Glass Cover ❖ Cleaning the machine Wipe the machine with a soft, damp cloth. Then wipe it with a dry cloth to remove the water. Important ❒ Do not use chemical cleaner or organic solvent such as thinner or benzene.
StellaC-EN-CopyF_V4_FM.
StellaC-EN-CopyF_V4_FM.book Page 65 Wednesday, July 4, 2001 11:23 AM 6.
StellaC-EN-CopyF_V4_FM.book Page 66 Wednesday, July 4, 2001 11:23 AM Specifications • Bypass tray (custom size): Vertical: 90 – 216mm, 3.5" – 8.5" Horizontal: 140 – 356mm, 5.5" – 14" • Paper tray unit: A4L, 81/2" × 14"L, 81/2" × 13"L, 81/4" × 14"L, 81/4" × 13"L, 81/2" × 11"L ❖ Copy paper weight: • Paper tray (Standard size): 60 – 90g/m2 (16 – 24 lb.) • Bypass tray: 60 – 157g/m2 (16 – 42 lb.) • Paper tray unit: 60 – 90g/m2 (16 – 24 lb.) ❖ Non-reproduction area: • Leading edge: 3 ± 2mm, 0.14" ± 0.
StellaC-EN-CopyF_V4_FM.book Page 67 Wednesday, July 4, 2001 11:23 AM Mainframe ❖ Power consumption: Mainframe only Full system *1 Warm up About 890W About 890W Stand-by About 90Wh About 100Wh During printing About 480Wh About 480Wh Maximum Less than 1,000W Less than 1,000W *1 Mainframe with the optional document feeder (ADF), paper tray unit. ❖ Dimensions (W × D × H up to exposure glass): • Type 1: 468 × 450 × 371mm (18.43 × 17.72 × 14.61 inch) • Type 2: 468 × 450 × 461mm (18.43 × 17.
StellaC-EN-CopyF_V4_FM.book Page 68 Wednesday, July 4, 2001 11:23 AM Specifications Document Feeder (ADF) (Option for Type 1) ❖ Mode: • ADF mode ❖ Original size: • A4L – A5KL • 81/2" × 14"L – 51/2" × 81/2"KL ❖ Original weight: • 1-sided originals: 52 – 105g/m2 (14 – 28 lb.) ❖ Number of originals to be set: • 30 sheets (80g/m2, 20 lb.) ❖ Maximum power consumption: • less than 50W (power is supplied from the main frame.) ❖ Dimensions (W × D × H): • 110 × 360 × 95mm (4.3 × 14.2 × 3.
StellaC-EN-CopyF_V4_FM.book Page 69 Wednesday, July 4, 2001 11:23 AM Paper Tray Unit (Option) Paper Tray Unit (Option) ❖ Copy paper weight: 60 – 90g/m2 (16 – 24 lb.) ❖ Available paper size: A4L, 81/2" × 14"L, 8 1/2" × 13"L, 81/4" × 14"L, 81/4" × 13"L, 8 1/2" × 11"L ❖ Maximum power consumption: 15W (power is supplied from the main frame.) ❖ Paper capacity: 500 sheets (80g/m2, 20 lb) ❖ Dimensions (W × D × H): 430 × 414 × 140mm (17.0 × 16.3 × 5.6 inch) ❖ Weight: Approx. 6kg (13.3 lb.
StellaC-EN-CopyF_V4_FM.book Page 70 Wednesday, July 4, 2001 11:23 AM Specifications 32MB Copier Memory Unit (Option) ❖ Memory capacity: 32MB ❖ Additional functions: Increased memory capacity ❖ Number of originals that can be stored: about 99 pages ITU-T No.
StellaC-EN-CopyF_V4_FM.
StellaC-EN-CopyF_V4_FM.
StellaC-EN-CopyF_V4_FM.
StellaC-EN-CopyF_V4_FM.
