WARNING: When using electrical products, basic cautions should always be followed, including the following: 1. Read these instructions. 2. Keep these instructions safe. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with a dry cloth. 7. Do not block any of the ventilation openings. Install in accordance with manufacturer’s instructions. 8.
ATTENTION: L’utilisation de tout appareil électrique doit être soumise aux precautions d’usage incluant: 1. Lire ces instructions 2. Gardez ce manuel pour de futures références. 3. Prétez attention aux messages de précautions de ce manuel. 4. Suivez ces instructions. 5. N’utilisez pas cette unité proche de plans d’eau. 6. N’utilisez qu’un tissu sec pour le nettoyage de votre unité. 7.
ACHTUNG: Beim Einsatz von Elektrogeräten müssen u.a. grundlegende Vorsichtsmaßnahmen befolgt werden: 1. Lesen Sie sich diese Anweisungen durch. 2. Bewahren Sie diese Anweisungen auf. 3. Beachten Sie alle Warnungen. 4. Befolgen Sie alle Anweisungen. 5. Setzen Sie dieses Gerät nicht in der Nähe von Wasser ein. 6. Reinigen Sie es nur mit einem trockenen Tuch. 7. Blockieren Sie keine der Lüftungsöffnungen. Führen Sie die Installation gemäß den Anweisungen des Herstellers durch. 8.
CUIDADO: Cuando use productos electrónicos, debe tomar precauciones básicas, incluyendo las siguientes: 1. Lea estas instrucciones. 2. Guarde estas instrucciones. 3. Haga caso de todos los consejos. 4. Siga todas las instrucciones. 5. No usar este aparato cerca del agua. 6. Limpiar solamente con una tela ceca. 7. No blacker ninguna de las salida de ventilación. Instalar de acuerdo a las instrucciones del fabricante. 8.
After unpacking your amplifier check that it is factory fitted with a three pin ‘grounded’ (or earthed) plug. Before plugging into the power supply ensure you are connecting to a grounded earth outlet. If you should wish to change the factory fitted plug yourself, ensure that the wiring convention applicable to the country where the amplifier is to be used is strictly conformed to. As an example in the United Kingdom the cable colour code for connections are as follows.
SPECIFICATIONS AH40 Supply Voltage on all models: Mains Fuse: ~115V ~220V/~230V Output Power Rating Inputs EQ Record Out Headphones DSP Loudspeaker Size (mm) Net Weight (kg) AH80 ~115V, ~220V/~230V 50/60Hz T1A L T3.15A L T500mA L T1.6A L 40W 80W 1 x Balanced Mic(XLR)/Unbalanced Line(Jack) 1 x Stereo Unbalanced Line (2 x Jack) 1 x Line/Hi-Z Instrument (Jack) Aux In (3.
INTRODUCTION The Audiohub range of multi instrument amplifiers is designed to be the centre of your audio world. The portable AH40 and AH80 amplifiers each feature 3 independent channels allowing connection of balanced XLR, line and HiImpedance/Instruments, as well as a dedicated Aux In. The AH40 and AH80 are driven by 40W and 80W output sections respectively. Additionally, the AH80 is equipped with a delay unit with Time and Feedback controls, and an FX send switch on each channel.
AH40 FRONT PANEL 1. CH1 MIC INPUT Balanced XLR input for low impedance microphone signals (200-600 Ohms). 2. CH1 LINE INPUT Unbalanced Jack input socket for connection of all line level signals (keyboard, signal processor, sample, drum machine, etc.). Note that the Mic and Line inputs may be used simultaneously, although it may be difficult to balance input levels, depending on your source. 3. CH1 LEVEL Adjusts the channel level, enabling the user to balance levels across channels. 4.
AH80 FRONT PANEL 1. CH1 MIC INPUT Balanced XLR input for low impedance microphone signals (200-600 Ohms). 2. CH1 LINE INPUT Unbalanced Jack input socket for connection of all line level signals (keyboard, signal processor, sample, drum machine, etc.). Note that the Mic and Line inputs may be used simultaneously, although it may be difficult to balance input levels, depending on your source. 3. CH1 LEVEL Adjusts the channel level, enabling the user to balance levels across channels. 4.
AH40/AH80 REAR PANEL (AH80 SHOWN. AH40 SIMILAR) 18. VOLTAGE SELECT SWITCH This is factory set to the correct voltage for the region the product is supplied to. If necessary it can be reset by removing the mains lead and then loosening (but not removing) the screws securing the cover. The cover can then be pivoted away from the switch which can be moved to select the alternate voltage. DO NOT reconnect the mains lead until the cover is replaced and secured.
BLOCK DIAGRAM Pre Out Mic FX Level 5 Band EQ Headphones Master Volume Line AH80 ONLY Aux In (3.
SAMPLE SETUP MP3 RECORD OUT MIC KEYBOARD BASS
NOTES
1.
