LX120H USER MANUAL
IMPORTANT SAFETY INSTRUCTIONS WARNING: When using electric products, basic cautions should always be followed, including the following. 1. Read all safety and operating instructions before using this product 2. The product should be powered by a three pin `grounded (or earthed) plug connected to a power socket with a grounded earth outlet. 3. All safety and operating instructions should be retained for future reference 4. Obey all cautions in the Operating instructions and on the back of the unit 5.
Page 3 /12
Laney OPERATING INSTRUCTIONS BEFORE SWITCHING ON After unpacking your amplifier check that it is factory fitted with a three pin 'grounded' (or earthed) plug. Before plugging into the power supply ensure you are connecting to a grounded earth outlet. If you should wish to change the factory fitted plug yourself, ensure that the wiring convention applicable to the country where the amplifier is to be used is strictly conformed to.
Laney OPERATING INSTRUCTIONS Dear Player, Thank you very much for purchasing your new Laney product and becoming part of the worldwide Laney family. Each and every Laney unit is designed and built with the utmost attention to care and detail, so I trust yours will give you many years of enjoyment. Laney products have a heritage which stretches back to 1967 when I first began building valve amplifiers in my parent’s garage.
Laney OPERATING INSTRUCTIONS 19 20 18 10 17 16 15 14 13 12 11 7 9 8 6 5 4 3 2 1 FRONT PANEL CONTROLS 1 This socket should be used for connecting your instrument to the amplifier. Only use a good quality screened cable. 2 Controls the volume level of the clean channel. 3 Controls the amount of bass or bottom end present on the clean channel. 4 Controls the amount of mid present on the clean channel. 5 Controls the amount of treble present on the clean channel.
Laney OPERATING INSTRUCTIONS 12 Controls the amount of mid present on the drive channel. 13 Controls the amount of treble present on the drive channel. 14 Controls the amount of signal returned from the onboard effects processor. The onboard digital effects have been custom designed by Laney to complement the LX120H with a choice of Delays, 15 Flange, Rotary, Octave Down, Chorus, Reverb and combinations of these.
Laney 25 OPERATING INSTRUCTIONS 24 23 21 22 21 Power inlet socket. Connect to your power source. Make sure the specified voltage is correct for your country! 22 This drawer contains the main safety fuse for the unit. USE ONLY THE CORRECT SIZE AND RATING OF FUSE AS SPECIFIED ON THE PANEL The mains fuse ratings are detailed in the specs section at the rear of this manual 23 Displays the model number, power requirements and serial number of the unit. 24 Connect your loudspeaker cabinets here.
Laney OPERATING INSTRUCTIONS QUICK START SETTINGS - Suggestions only, experiment! LX120H 1 EFFECTS Dly+Ch Off Rev+Ch 2 1 2 Octave 1 Rev LINE OUT FOOTSWITCH CD/LINE IN DRIVE EFFECT CLEAN OUT 1 2 Chorus 2 Rotary Flange 1 0 POWER DRIVE EQUALISATION 1 Delay 2 3 4 XTS LEVEL TREBLE MID BASS ON MASTER CRUNCH TREBLE MID BASS VOLUME INPUT BASS VOLUME INPUT BASS VOLUME INPUT BASS VOLUME INPUT CLEAN SETTINGS LX120H 1 EFFECTS Dly+Ch Off Rev+Ch 2 1 2 Octave 1 Rev LINE OUT FOOTSWITCH
Laney OPERATING INSTRUCTIONS SAMPLE SYSTEM General Notes Amplifier connection: In order to avoid damage, it is advisable to establish and follow a pattern for turning on and off your equipment. With all system parts connected, turn on source equipment, tape decks, cd players, mixers, effects processors etc. BEFORE turning on your guitar amplifier. Many products have large transient surges at turn on and off which can cause damage to your speakers.
Laney SPECIFICATIONS Supply Voltage Mains Fuse Power Consumption Output Power Rating Features Footswitchable Digital Effects EQ Input Impedance Size Unit Weight Packing Weight OPERATING INSTRUCTIONS ~100V, ~120V, ~220V, ~230V, ~240V 50/60Hz Factory Option ~220V>~240V = T1A L.
BLOCK DIAGRAM LINE OUT INPUT CD IN CLEAN EQ SECTION EQ SECTION FX SEND XTS FX RETURN POWER AMP REVERB / EFFECTS This loop is a series type so all of your signal will go through your FX unit. DRIVE LOUDSPEAKERS FOOTSWITCH Laney POWER TO THE MUSIC METAL BLUES JAZZ ROCK AMPICONS ARE HERE TO HELP! @ In the interest of continued product development, Laney Reserves the right to amend product specification without prior notification.
